Showing posts with label do. Show all posts
Showing posts with label do. Show all posts

Saturday, May 17, 2014

How do I Install Tie Rod Ends on a 96 Honda Accord

How do I Install Tie Rod Ends on a 96 Honda Accord?

Your 1996 Honda Accords tie-rod ends are the steering components that attach the steering linkage and linkage parts to the steering knuckles with a hardened steel ball stud. A tie-rod end can be replaced alone, but many automotive parts manufacturers recommend replacing the entire tie-rod as a whole and often sell these components fully assembled. You may want to purchase just the tie-rod ends, if available, if you are looking to conduct this repair method. This procedure does not require special tools and can be done at home with little automotive experience or knowledge.

Instructions

Removing the Tie-Rod Ends

    1

    Unscrew the lug nuts on your Accord slightly, then raise your Accord and support it with jack stands.

    2

    Remove the lug nuts and take the front wheels off.

    3

    Loosen the jam nut using one open-end box wrench while holding onto the tie-rod end with another. When the thread is exposed, mark it with some correction fluid to erence the new tie-rods position.

    4

    Take out the cotter pin on the tie-rod end stud and loosen the nut, but dont remove it.

    5

    Pry the tie-rod end from the steering knuckle arm using a two-jaw puller. Now remove the nut and separate the tie-rod end from the steering knuckle arm.

    6

    Separate the tie-rod end from the tie-rod by unscrewing it.

Installing the New Tie-Rod End

    7

    Screw on the tie-rod end up to the marked point on the tie-rod; you may need your open-end wrench. Place the tie-rod stud into the steering knuckle arm.

    8

    Screw on the nut to the tie-rod end stud and torque it to 32 foot-lbs with your torque wrench. Install the new cotter pin.

    9

    Repeat all steps in each section for the other side of your Accord.

    10

    Install the wheels and screw on the lug nuts finger tight. Lower your Accord and torque the lug nuts to 80 foot-lbs.

Read More.. >

Wednesday, May 14, 2014

How do I Install 2001 883 Harley Sportster Push Rods

How do I Install 2001 883 Harley Sportster Push Rods?

Pushrods, on the exterior of the cylinders on the right side of the engine, are part of an old-fashioned connection between the cam shaft and the exhaust and intake valves on your 2001, 883 cubic centimeter, V-twin Harley engine. Pushrods are specific to 883 and 1200 Sportster engines and Big Twins, but their operation, installation and removal is identical in all 2001 Harley V-Twin engines. Adjustable pushrods can conveniently be adjusted without having to first partially disassemble the top end of the engine. The initial top end job needed to install replacement pushrods is not for novices as clearances are tight, and many tools and some skill are required.

Instructions

    1

    Close the petcock. Put the motorcycle in fifth gear.

    2

    Loosen the fender tab screw with an Allen wrench. Remove the seat.

    3

    Loosen the battery cable from the negative terminal with an open end wrench. Disconnect the cable.

    4

    Raise the motorcycle on a motorcycle jack until the rear tire clears the ground. Ensure the bike is stable.

    5

    Remove the front and rear spark plugs with a spark plug socket and a socket wrench.

    6

    Rotate the engine by rotating the rear wheel. Rotate the engine until the front piston, as viewed through the spark plug hole, is at the top of its stroke and both front lifters are at their lowest point in the compression cycle.

    7

    Remove the front rocker box cover by loosening the rocker cover bolts with a rocker cover wrench. Remove the metal D-ring. Remove the gasket and discard.

    8

    Insert a small, flat head screwdriver blade into the cast loop of the spring cap retainer at the top of the rear pushrod cover for the front cylinder.

    9

    Rotate the screwdriver bottom toward the outboard side while pushing down. Remove the spring cap cover. Repeat the procedure for the other front cylinder pushrod.

    10

    Collapse the upper and lower push rod covers.

    11

    Alternately loosen each of the four rocker arm support plate bolts in 1/4 turn increments until all four bolts are loose. Remove the rocker arm support plate assembly.

    12

    Remove the push rod covers from the cylinder head and lifter cover bores. Remove the three O-rings from the push rod covers and discard.

    13

    Remove the pushrods by hand.

    14

    Assemble the new pushrod covers. Insert the pushrod cover adapters in the cover retainers.

    15

    Insert the new pushrods in the cylinder head and lifter cover bores. Install the new cover O-rings included with the new pushrods.

    16

    Replace the rocker arm support plate into the rocker housing. Loosely install the four rocker arm support plate bolts.

    17

    Tighten the four rocker arm support plate bolts in a cross pattern by tightening each bolt 1/4 turn at a time. Final tighten the bolts to 18 to 22 foot pounds of torque with a torque wrench and a "dog bone" torque adapter.

    18

    Install a new rocker box cover gasket. Replace the D-ring.

    19

    Replace the rocker box cover. Tighten the rocker box cover bolts in a cross pattern to 20 foot pounds of torque with a torque wrench.

    20

    Extend the adjusting screws to remove lash in the pushrods.

    21

    Compress the hydraulic unit in the exhaust lifter four complete turns and tighten the lock nut.

    22

    Adjust slack in the pushrod with your fingers after waiting five minutes. Repeat all procedures for the rear cylinder.

    23

    Replace the spark plugs and tighten them with a spark plug socket and socket wrench.

    24

    Lower and remove the motorcycle jack. Shift the motorcycle into neutral.

    25

    Start the motorcycle and check for leaks.

Read More.. >

Sunday, April 20, 2014

How do I Replace a Timing Belt on a 2000 Hyundai Elantra

The Hyundai Elantra is a series of compact cars that Hyundai has manufactured since 1990. The 2000 model represents the last year of the second generation Hyundai, which had a 4-cylinder, 2.0-liter engine as its standard engine. This engine uses a timing belt to synchronize the movement of the camshaft and crankshaft as opposed to a timing chain. The timing belt in a 2000 Hyundai requires replacement approximately every 60,000 miles.

Instructions

    1

    Disconnect any components necessary to access the cover of the timing belt. Remove the timing belt cover with a socket wrench.

    2

    Turn the crankshaft clockwise to position the No. 1 piston at the top dead center position as indicated by the timing marks on the crankshaft. Disconnect the tensioner for the timing belt and the idler pulley with a socket wrench. Remove the timing belt from the camshaft sprocket and the crankshaft sprocket.

    3

    Turn the camshaft sprocket clockwise to align its timing marks and ensure the timing marks for the crankshaft timing are still aligned. Connect the tensioner for the timing belt with a socket wrench, but do not tighten the pulley bolt for the tensioner. Install the idler pulley and tighten its mounting bolt to between 32 and 41 foot-pounds.

    4

    Place the timing belt over the sprocket of the camshaft, then over the sprocket of the crankshaft. Turn the timing belt tensioner counterclockwise to place tension on the timing belt. Apply 5 pounds of force to the middle of the longest span of the timing belt. The deflection of the timing belt will be between 0.16 inches and 0.24 inches when the timing belt is at the correct tension.

    5

    Tighten the pulley bolt for the timing belt tensioner to between 32 and 41 foot-pounds with a torque wrench. Turn the crankshaft sprocket clockwise by one turn to align the timing marks on the crankshaft sprocket. Adjust the timing belt tension as required.

    6

    Replace the cover for the timing belt. Install any additional components that you removed in step one to access the timing belt.

Read More.. >

Thursday, April 17, 2014

How Do I Replace a 2003 Expedition Side View Mirror Assembly

How Do I Replace a 2003 Expedition Side View Mirror Assembly?

The 2003 Ford Expedition features both a left and right side view mirror. These mirrors are important for backing up the large SUV and for keeping a caul eye on traffic behind the vehicle. Because of its larger size, the Expedition is a hard vehicle to back up while looking out the back window, and it takes a certain amount of skill to be able to do so.

Instructions

    1

    Open the door on the Expedition with the mirror that needs to be replaced.

    2

    Lower the window all the way down then turn the ignition off and remove the key.

    3

    Remove the outer screw located on the rear side of the door panel with a flat head screwdriver.

    4

    Remove the two retaining bolts located at the bottom of the door panel with a 7 mm socket wrench.

    5

    Pry off the door handle cover with a pry tool.

    6

    Remove the window control module cover with the pry tool and disconnect the wire harness connections under the cover.

    7

    Pry off the panel under the door pull bar with the pry tool then remove the two screws under the panel. Use the T-27 Torx head screwdriver to remove the screws.

    8

    Pry around the bottom and side of the door panel with the pry tool. When the retaining snaps are all unseated, reach behind the door panel and disconnect any remaining wire harness connections. Remove the door panel.

    9

    Disconnect the side view mirror wire harness.

    10

    Remove the three retaining bolts located on the door frame opposite the side view mirror with an 11 mm socket wrench. Be caul not to allow the mirror to fall and scratch the door when removing the last retaining bolt.

    11

    Feed the wire harness out through the access hole of the door frame and remove the old mirror.

    12

    Install the new mirror by reversing Steps 9 through 11.

    13

    Reinstall the door panel by reversing Steps 3 through 8.

Read More.. >

Tuesday, April 1, 2014

How do I Troubleshoot a Defroster on a 79 Oldsmobile

How do I Troubleshoot a Defroster on a 79 Oldsmobile?

You can troubleshoot the defroster in a 1979 Oldsmobile yourself without the headache of finding a mechanic and having to make a decision about repairs on the spot. There is a possibility you might need a voltmeter to troubleshoot your vehicle. This can be purchased at any auto parts store.

Instructions

    1

    Check the cars coolant level. The warm air from a car defroster comes from the engines coolant. A low engine coolant level could be causing a lack of heat from the defroster. Also check that the heater core is not plugged. The coolant flows through the heater core to warm the defroster.

    2

    Check to see if the vacuum hose is detached or damaged. If it is, this can keep the doors from working and cause a lack of control in air direction. Ducts are responsible for moving the heater core air into the passenger cabin of the car. Vacuum-powered doors are responsible for the direction of air flow inside the ducts in most vehicles. Check the cabin air filter, too. If the cabin air filter is full of debris, this can also lead to a reduced flow of air.

    3

    Use the car manual as a guide to find the fuse box and also to learn the proper positioning for the blower fuse. Check inside the fuse box to assess the blower fuse. Use the voltmeter to make sure the blower is grounded and can receive power if the fuse is undamaged.

Read More.. >

Sunday, March 23, 2014

How Do I Replace an O2 Sensor in a 1998 Chevy Blazer

How Do I Replace an O2 Sensor in a 1998 Chevy Blazer?

The 1998 Chevy Blazer has three oxygen (O2) sensors. Two are located up on the front Y-pipe bolted to the V-6 engines manifold. These two sensors detect the fuel-to-air mix in the exhaust and transmit that information to the powertrain control module (PCM). From there, the PCM makes adjustments to achieve the lowest emissions possible while still running properly. The last O2 sensor is located after the catalytic converter. This sensors job is to monitor the efficiency of the catalytic converter.

Instructions

    1

    Apply the parking brake to lock the rear wheels.

    2

    Open the hood to the 1998 Chevy Blazer to allow some light down into the engine compartment. This will be helpful when under the vehicle to replace the front oxygen sensor(s). If you are replacing the rear sensor, opening the hood is not necessary.

    3

    Lift one front side of the Blazer up high enough to rest it on a jack stand and then lift the other side and rest that side on a jack stand.

    4

    Put on the safety glasses and crawl underneath the Blazer to locate the oxygen sensor(s) being replaced. One is located on the left-side Y-pipe up near the manifold connection, the other is on the right-side Y-pipe near the manifold and the rear sensor is located in the catalytic converter pipe just behind the shell of the converter.

    5

    Unlock the wire harness plug from the O2 sensor plug. Use the small screwdriver to press inward and release the lock while pulling the O2 sensor plug and wire away from the wire harness plug.

    6

    Spray penetrating oil around the threaded connection of the O2 sensor where it screws into the O2 sensor port of the exhaust piping. Allow the oil a few minutes to soak in.

    7

    Thread the O2 sensor wire through the closed end of the 22 mm wrench and then place the closed end of the wrench onto the sensors hex-head. Turn the wrench to the left (counterclockwise) to remove it from the port. Remove the sensor.

    8

    Inspect the threads of the replacement sensor. Most will come with a light coating of special anti-seize compound already on the threads. Some O2 sensor manufacturers will provide a small tube inside the box. If applying the compound, be sure to avoid getting the compound on the thimble-tip of the sensor. Only place a small amount on the threads of the sensor.

    9

    Thread the sensor into the port by hand to avoid crossing the threads of the sensor. Tighten the sensor with the wrench after threading the wire through the closed end again. Only tighten the sensor snugly. Over-tightening the sensor risks stripping the threads of the sensor and/or possibly damaging the threads to the sensor port.

    10

    Connect the replacement sensor wire plug to the wire harness plug before crawling out from under the Blazer with the tools and old sensor(s) and lowering the vehicle.

Read More.. >

Tuesday, March 18, 2014

What Does a Ballast Resistor Do

What Does a Ballast Resistor Do?

The process of starting a car involves more than simply turning the key to fire up your engine. Between the battery and the starter, a ballast resistor helps regulate the voltage.

Definition

    WordNet Search defines a ballast resistor, most commonly found in an automobile ignition system, as a device "inserted into a circuit to compensate for changes, [such] as those arising from temperature fluctuations."

Function

    A ballast resistor helps regulate voltage flowing in an electrical system to avoid overloads or battery drainage.

Use in Automobiles

    As the starter motor begins to crank the engine, it causes a significant drain on the battery. The ballast resistor allows the ignition system to operate at a lower voltage until the engine starts. After ignition, the alternator begins to recharge the battery, restoring the regular voltage. The ballast resistor then functions to regulate the voltage going to the ignition system to avoid additional wear on the system.

Additional uses

    Low-voltage lighting systems, such as florescent, LED and neon lights, frequently contain ballast resistors.

Read More.. >

Tuesday, January 28, 2014

How Do I Replace an Oxygen Sensor in a 1985 Chevy S 10 Blazer

How Do I Replace an Oxygen Sensor in a 1985 Chevy S-10 Blazer?

The single oxygen sensor on the 1985 Chevy S-10 Blazer is a more primitive design than todays O2 sensors. Its erred to as a non-heated single (one) wired sensor. While it functions similarly to todays sensors, it demands that the engine is up to operating temperature, including the engine coolant, before it begins to monitor the fuel-to-air ratio. Todays sensors have multiple wires with built-in heaters that heat them up quickly to begin monitoring the emissions more readily. This lessens the amount of pollutants allowed into the air while the vehicle is warming up.

Instructions

    1

    Apply the parking brake of the 1985 Chevy S-10 Blazer and then open the hood. Access to the oxygen sensor is on the lower side of the engine, but youll have more adequate lighting with the hood opened.

    2

    Hoist one front quarter of the Blazer up with a jack placed under the frame rail and then lower the jack and Blazer onto a jack stand. Repeat for the other front quarter to elevate the front end completely.

    3

    Put on the safety glasses and crawl underneath the Blazer with the remaining items.

    4

    Follow the front exhaust pipe to where it connects to the manifold on the drivers side to locate the oxygen sensor.

    5

    Follow the wire coming off the end of the oxygen sensor to the wire harness plug mating connection to the oxygen sensor plug. Lift up the release tab of the wire harness plug and then pull the oxygen sensor plug out.

    6

    Put the oxygen sensor socket onto the ratchet and then align the wire of the sensor into the slit on the side of the socket.

    7

    Place the socket fully onto the hex-head of the sensor and then turn the ratchet counterclockwise to remove it from the sensor exhaust port. Remove the sensor.

    8

    Inspect the replacement oxygen sensor threads. If there is no anti-seize compound on the threads, apply a thin coating of electrically conductive anti-seize compound to the threads, being caul not to get the compound on the head of the sensor.

    9

    Hand-thread the replacement sensor into the oxygen sensor exhaust port as far as it will go.

    10

    Tighten the sensor snugly with the ratchet and oxygen sensor socket (placing the sensor wire into the socket slit), but do not over-tighten it. The threads of the sensors are made of much softer metal than the exhaust system to prevent damaging the mating threads of the system. Because of this, its easy to strip the threads of the sensors.

    11

    Connect the sensor wire plug to the mating plug of the wire harness until the lock clicks into place.

    12

    Lower the Blazer and close the hood.

Read More.. >

Tuesday, January 14, 2014

How do I Reset the Airbag in a 1998 Infiniti I30

How do I Reset the Airbag in a 1998 Infiniti I30?

When your Infiniti I30s diagnostic system detects a malfunction with the vehicle, it issues an error code. The SRS, or Supplemental Restraint System, light illuminates as a result of an error code related to the airbag system. You can disconnect the battery to reset the light but this resets the entire computer, so thats not the best option. Or you can obtain an OBD II scanner from an auto parts store to reset the computer and shut off the SRS light. This is the preferred way and takes just a few minutes of your time. Only reset the airbag after it has been inspected and, if necessary, repaired by a qualified mechanic.

Instructions

    1

    Locate the OBD port under the dashboard near the steering column.

    2

    Plug the OBD-II scanner into the OBD port, then power on the scanner.

    3

    Put the key into the ignition and turn it to the "On" position.

    4

    Wait for the error code to display on the face of the scanner. Select the "Erase" or "Clear" codes command. Wait while the scanner clears the code and returns to the main menu.

    5

    Unplug the scanner and start the engine. Verify that the SRS light has shut off of the instrument panel. The airbag is now reset.

Read More.. >

Friday, January 10, 2014

Do Exhaust Insulating Wraps Work

Do Exhaust Insulating Wraps Work?

Exhaust "headers" are replacement manifolds designed to increase your engines performance. In racing or performance applications both automotive and motorcycle, they are often wrapped with a heat shielding substance. There are a few simple reasons to wrap your exhaust.

Under Hood Temperatures

    In automotive applications, exhaust wraparound headers helps reduce under hood temperatures allowing for cooler air intake. Cooler air intake produces higher horsepower, as cooler air contains more oxygen, which aids the burning process in the cylinder. Exhaust wraps under the hood can reduce temperatures significantly.

Velocity

    Theoretically, exhaust wrap helps contain exhaust heat, making the exhaust gases move more rapidly away from the engine and towards the tail pipe. This increased exhaust velocity increases potential horsepower by evacuating the cylinder more quickly and allowing the piston to move upward with less resistance.

Scavenging

    The velocity also helps with scavenging, or the removal of combustion waste or exhaust from the cylinder more completely. This results in a cleaner, faster burn of the fuel air mix on the next piston stroke. The increased scavenging results in more efficient combustion and potential horsepower.

Read More.. >

Tuesday, December 3, 2013

How to Do a Transmission Flush on an Odyssey

The Honda Odyssey transmission fluid changes color over time due to worn clutch material contaminating the fluid. It is not open to the atmosphere and is not affected by the engine. Any contamination in the transmission is strictly due to internal wear, which is normal. The Odyssey does not have a traditional filter or oil pan on the transmission. It has a large magnetic drain plug, which attracts all metal shavings that must be cleaned before flushing.

Instructions

    1

    Drive the vehicle to a reputable service facility. Instruct the service writer to drain the transmission, and remove and clean all the metal particles off the magnetic drain plug. When this is clean, refill the transmission.

    2

    Instruct the service writer to perform a power flush on the transmission. The reasoning behind this is that it does little good to perform a power flush as long as the magnetic plug is covered with metallic chips. The transmission only gets a flush when the fluid turns from red to brown, which takes a long time. Draining and filling the transmission with fluid does no good, since the majority of fluid is in the torque converter and pump. As soon as the vehicle starts up, the fluid will be dark again. Flushing the transmission involves removing the transmission lines from the radiator and connecting them to a large power flushing machine. The mechanic starts the engine, and the machine forces new fluid into the transmission and pulls the contaminated fluid out until the fluid flows red. This usually requires the machine to dispense about 13 to 18 quarts of new transmission fluid.

    3

    Request the service writer to add a clutch-modifier fluid to the transmission fluid after the flush is complete. This adheres to the clutch discs and creates a rougher surface for better clutch engagement. Now the transmission will shift better and faster. The biggest benefit is that it extends the life of the transmission by at least 40 percent.

Read More.. >

Thursday, November 28, 2013

How Do I Change an Oxygen Sensor on a 1997 Hyundai Accent GL

The 1997 Hyundai Accent oxygen sensor threads into the exhaust manifold beneath the heat deflector under the car. The O2 sensor regulates the fuel consumption of the engine based upon the oxygen saturation of the exhaust. If the gas mileage in your car has inexplicably decreased substantially and the check engine light is on, you may have a failing O2 sensor. Buy a replacement sensor at an auto parts store or Hyundai dealership.

Instructions

    1

    Raise the Accent with a jack. Rest the car on a set of jack stands.

    2

    Disconnect the wiring harness from the O2 sensor just beneath the exhaust manifold heat deflector.

    3

    Remove the bolts on the outer edge of the heat deflector with a socket and ratchet. Set the heat deflector and bolts aside in a safe location. Remove the O2 sensor with an O2 sensor socket and ratchet.

    4

    Install the new sensor by hand to avoid cross threading it. Tighten the sensor with an oxygen sensor socket and ratchet. Reconnect the wiring harness on the O2 sensor by pressing it into place.

    5

    Replace the heat deflector. Secure the deflector with the bolts and tighten the bolts with a socket and ratchet.

    6

    Raise the car slightly with a jack and remove the jack stands. Lower the car to the ground.

Read More.. >

Tuesday, November 26, 2013

How Do I Change a Knock Sensor in a Ford 5 4L

How Do I Change a Knock Sensor in a Ford 5.4L?

A knock sensor is a piezometric crystal that advances or retards the engine based on load. Knock sensors are typically located on the intake side of the Ford 5.4-liter engine. All knock sensors connect to an electrical wiring harness and links to the vehicles On Board Computer (OBC). A knock sensors fails like a light bulb fails -- it simply wears out. When a knock sensor does fail, the OBC will automatically retard the engine to minimal fuel efficiency and put the engine in limp mode. The check engine light is a symptom of knock sensor failure.

Instructions

    1

    Disconnect the negative terminal from the vehicles battery using the 10- to 12-mm box wrench to prevent short-circuiting while changing out the knock sensor.

    2

    Disconnect the electrical wiring harness from the knock sensor by pulling it apart manually or using long-handled needle-nose pliers. This action is similar to pulling a plug out of an electrical wall socket.

    3

    Remove the knock sensor by attaching the wobble or swivel bit to the end of the 3/8-inch extension and fastening it to the socket that fits. Insert the socket over the knock sensor. You need the wobble or swivel bit at the end of the extension to access the sensor due to the configuration of the intake manifold.

    4

    Connect the ratchet to the end of the 3/8-inch extension that is attached to the wobble or swivel bit and the socket. Use the ratchet to loosen the sensor from the engine block by turning it gently to the left. Remove the defective sensor from the socket and place the defective sensor on the work bench.

    5

    Add a dab of white lithium grease to the male end of the electrical connections of the new knock sensor to prevent corrosion build up and to make insertion easier.

    6

    Use the socket with the extension to manually screw the new knock sensor to the engine block to avoid cross-threading. Cross-threading occurs when the threads of the sensor do not match up with the threads of the engine block.

    7

    Reattach the electrical harness to the sensor and reconnect the negative terminal of the battery.

Read More.. >

Friday, November 15, 2013

How Do I Read 1995 Ford F150 Check Engine Codes

How Do I Read 1995 Ford F150 Check Engine Codes?

The Ford F-150s made in 1995 have check engine lights that come on when the computer system in the truck senses trouble. Sensors send information to the power train control of the truck when the information does not match up to what the trucks known limits are. The trucks computer generates a code and displays the check engine light. Each code refers to a specific issue that can be pinpointed once you have retrieved the code from the trucks onboard diagnostic system.

Instructions

    1

    Remove the cover off the diagnostic port of the Ford, located under the dashboard on the left-hand side.

    2

    Plug in the OBD scanner into the link of the diagnostic port. Code scanners can be found at your local auto-parts store. You can also ask a local auto-parts store if they can plug in a store-owned scanner for you to check the codes.

    3

    Run the self-test with the code scanner. Read the manufacturers instructions to find out how your particular scanner runs the self-test.

    4

    Write down the codes as the scanner reports them. There may be several codes--allow the scanner to run through the entire test.

    5

    Move through the codes as they appear, but do not delete them.

    6

    Remove the data cable and replace the cover over the port when complete.

Read More.. >

Saturday, November 9, 2013

How Do Automatic Wiper Activated Headlamps Work

Automatic wiper-activated headlamps in vehicles are helpful when driving in rainy conditions. This feature allows the vehicles headlamps to automatically turn on in the daytime when the wipers are activated.

Function

    Automatic wiper-activated headlamps are connected to the vehicles wiper system, turning on when the vehicle is in gear and the windshield wipers are activated. The headlamps can be turned on and off manually like regular headlamps; however, if the headlamps are off, activating the wipers will immediately turn them on.

Features

    The mechanism that triggers the headlamps works with a relay circuit that connects the vehicles headlight circuit and wiper circuit, both of which work to turn on the low-beam headlamps when the windshield wipers are activated. The relay circuit includes a delay circuit that allows for the continuous operation of the headlamps and an interlocking safety mechanism to prevent the low and high beams from operating simultaneously.

Manual

    Normal or manual headlight operation will automatically be triggered when the vehicle is placed in the Park or Neutral positions, or if the windshield wiper blades are turned off.

Read More.. >

Saturday, October 19, 2013

How Do I Reset an Airbag in a 2001 Mazda B3000

How Do I Reset an Airbag in a 2001 Mazda B3000?

The Supplemental Restraint System (SRS) or airbag light on a 2001 Mazda B3000 is designed to alert the driver to malfunctions in the airbag system. The light may illuminate on the instrument panel for reasons unrelated to the airbag, or it may illuminate because of a real problem that needs to be addressed. If you have recently replaced the vehicles battery or installed a new stereo, theres a good chance that the airbag just needs to be reset. Perform the following steps to shut off the light. If the light turns itself back on, then you should take it to a qualified mechanic to have the airbag system examined.

Instructions

    1

    Insert the key into the ignition and turn it to the "ACC" position then turn it off again. Do this 10 times quickly but do not start the engine. If this procedure does not reset the SRS light, proceed to Step 2.

    2

    Locate the fuse panel cover on the drivers side dashboard. Open the panel by pulling down on the cover from the top by hand. Locate the SRS fuse by referring to the fuse diagram. Pull the fuse out with the fuse puller and examine it to see if it has blown. If it has, replace it. This should reset the light. If not, proceed to Step 3.

    3

    Pop the hood on your Mazda B3000 and loosen the bolt on the negative cable clamp with a pair of pliers. Slip the clamp off the negative battery terminal, taking care not to let it touch anything. Wait about 10 minutes then reconnect it to the terminal and tighten the bolt. Close the hood and start the engine. Examine the instrument panel to verify that the SRS light has shut off.

Read More.. >

Friday, October 18, 2013

How Do I Replace a 2000 Hyundai Sonata GLS Oxygen Sensor

The oxygen sensors in the 2000 Hyundai Sonata GLS are threaded into the exhaust manifold and the exhaust pipe near the catalytic converter. When an oxygen sensor malfunctions, your car will burn a significant amount of additional fuel. To save the unnecessary fuel expense and possible long-term engine damage, you should replace the sensors as soon as possible. Buy sensors for your Sonata from an auto-parts store or Hyundai dealer.

Instructions

    1

    Raise the Sonata with a jack. Rest the car on jack stands for stability.

    2

    Locate the oxygen sensor either on the manifold or near the catalytic converter, depending on which one you need to change. Pull the wiring connection apart. Remove the oxygen sensor using a wrench.

    3

    Coat the threads of the sensor with anti-seize. Select an anti-seize compound designed for electrical components. Insert the new sensor by hand. Torque it to 40 foot-pounds with your torque wrench.

    4

    Push the two ends of the wiring harness together. The connector will click when it is attached. Repeat the replacement process on the second oxygen sensor if necessary. Lift the car slightly and pull the jack stands out of place. Lower the car to the ground.

Read More.. >

Sunday, October 13, 2013

How do I Determine Which Fuel Pump Is Needed for a 99 Chevrolet Silverado V6

How do I Determine Which Fuel Pump Is Needed for a 99 Chevrolet Silverado V6?

General Motors engineered the fuel system of the 1999 Chevrolet Silverado V6 4.3L with and without an evaporative emissions system monitoring system. Chevrolet designed the fuel pump as an integrated module assembly, combining the fuel pump and fuel level sensor together as a single unit. Delphi manufactures fuel pumps for General Motors. 1999 Chevrolet Silverados equipped with the evaporative emissions monitoring system also have a pressure sensor built into the fuel pump module assembly. The engine computer applies vacuum to the fuel tank and monitors the sensor to verify the tank holds the vacuum. If the tank leaks, pressure drops and the check engine light will turn on.

Instructions

    1

    Park the vehicle on a flat surface such as a driveway. Set the parking brake and remove the keys from the ignition.

    2

    Chock the front tire of the 99 Silverado with wheel chocks to prevent the vehicle from rolling.

    3

    Lift the left rear drivers side tire of the 99 Chevy with the floor jack. Place a jack stand under the axle tube for safety.

    4

    Remove the plastic lug nut covers by hand using a 3/4 inch impact socket.

    5

    Remove the lug nuts using the 1/2 inch drive impact wrench and a 13/16 inch socket. Remove the left rear tire.

    6

    Lean into the wheel well toward the front of the bed. Shine the flashlight onto the top of the fuel tank. Extend the inspection mirror to inspect the top of the fuel pump module assembly.

    The fuel pump module assembly is round where it inserts into the tank, and has three fuel lines attached to it. The fuel pump module assembly also has a square four-wire harness plugged into it to provide power to the fuel pump and to measure the fuel level.

    7

    Look for a small black sensor with a wide flat three-wire harness plugged into it. Also inspect the four-wire fuel pump harness for a tag with three prominent letters printed on it.

    Vehicles equipped with evaporative emissions monitoring have the black sensor, two wiring harnesses plugged into the fuel pump module assembly and have a code on the four-wire fuel pump harness labeled "TCF." Delphis aftermarket part number for this fuel pump module assembly is FG0053.

    Vehicles without evaporative emissions system monitoring do not have the black sensor, only have one wiring harness plugged into the fuel pump module assembly and have a code labeled on the four-wire fuel pump harness labeled "TCU." Delphis aftermarket part number for this fuel pump module assembly is FG0271.

Read More.. >

Thursday, October 3, 2013

How do I Lower 1995 Harley 883 Sportster

You can lower your 1995 Harley 883 Sportster on either the front or the back end. Lowering the front requires you to disassemble your forks and install shorter fork springs. Most Sportster riders do not shorten the fork springs for various reasons, including compromised handling. Lowering the rear end of your motorcycle is a simple job that wont affect the safety of the bike. You can get that slammed-in-the-weeds look for your Sportster by replacing your stock, 13-1/2-inch shocks with shorter ones.

Instructions

    1

    Remove your right and left saddlebags. If you have throw-over saddlebags, remove the seat by unscrewing the Allen bolt that secures your seat to the rear fender. You will probably not have to remove your saddlebag supports. If you have bolt-on saddlebags, immobilize the nut inside your fender with a box wrench, then loosen the nut on the outside of the fender with a socket wrench.

    2

    Raise the bike on a motorcycle jack until the rear wheel is completely off the ground. Make sure your motorcycle is stable.

    3

    Remove the lower shock mounting bolt and the washer nut on one side of your Sportster. Set them aside for reuse. Remove the upper bolt, washer and cover and set aside for reuse. Remove the shock absorber. Repeat on the other side.

    4

    Install the new shorter shocks, one side at a time. Put thread locker on the lower shock mounting bolt and reinstall. Reinstall the upper shock mounting bolt, using thread locker. Repeat for the opposite side.

    5

    Lower the bike carefully and support on the jiffy stand. Reinstall the saddlebags and the seat.

Read More.. >

Monday, September 30, 2013

Do Saturns Have Catalytic Converters

Do Saturns Have Catalytic Converters?

A catalytic converter, or catalyst, is responsible for reducing the amount of pollutants that emit into the atmosphere while a vehicle is being driven. Saturn vehicles do have catalytic converters.

Types

    Some cars have an oxidation catalyst that reduces carbon monoxide and hydrocarbons, also known as a two-way catalyst. Some Saturn catalysts control the emission of nitrogen as well, known as three-way catalysts.

Emission Check

    Catalysts can become clogged and therefore must be serviced. Many auto shops can perform inspections to see if your Saturn has a plugged catalyst; there are also emission inspection facilities for diagnosis and/or repair.

Replacement

    Although catalysts dont often break from normal use of your car, replacing one is not such a detailed process. If you do it yourself, be sure to acquire the correct catalyst for your Saturn and new flange gaskets, nuts and bolts and anti-seize compound to coat them with.

Read More.. >