Showing posts with label transmission. Show all posts
Showing posts with label transmission. Show all posts

Thursday, May 15, 2014

Geo Metro Transmission Problems

Geo Metro Transmission Problems

The Geo Metro enjoyed popularity since its release in 1989. Geo Metro was released with as a coupe, convertible and sedan with three trim levels. Its fuel efficiency earned it the title Most Fuel Efficient car in America. Some Geo Metros had some issues with the transmission.

Recalls

    General Motors issued a recall on the 1997 Geo Metro. The recall went out to owners on September 21, 1998. The 1997 Geo Metros equipped with an automatic transmission contained a faulty neutral safety switch. The shift level appeared to be in park but could be moved without having the key inserted or the shifter being moved. This created a dangerous potential for the vehicle to roll back if parked on an inclined surface. Dealers replaced the shifter assembly to fix the issue.

Signs and Symptoms

    Transmission problems manifest in different ways. Low transmission fluid due to a transmission leak is one symptom of a transmission problem. A Geo Metro with low transmission fluid shifts into drive slowly. During driving, gear slippage and rough shifting or failure for the transmission to age are all symptoms of a transmission issue. The check engine light may illuminate if a transmission fault code generates. Using a code retrieval tool, the specific code can be pulled from the vehicles computer. This code will correspond to an error and is useful for a mechanic in transmission diagnosis and repair.

Prevention/Solution

    Check the transmission fluid level. Take notice of the fluid color. Brown and burnt-smelling fluid indicates a fluid change is needed. Fluid change intervals correspond to how much a car is driven. More frequently driven vehicles require transmission fluid changes more often. At the first sign of transmission trouble have the engine serviced to avoid further damage and more costly repair.

Read More.. >

Chevy Transmission Problems

Chevy Transmission Problems

Chevrolet transmission problems led General Motors to recall 276,729 automobiles in 2009, according to the National Highway Traffic Safety Administration (NHTSA). The recall affected 2009 model year Chevy Colbat, HHR, Malibu and Traverse vehicles.

Safety Defect

    These 2009 Chevrolets were recalled for failing to comply with Federal safety standards. Per the NHTSA, there is a safety risk that the transmission shift cable adjustment clip might not be fully engaged. This could result in a serious problem if the driver shifts to "Park," and removes the ignition key, but the transmission gear isnt really in "Park" mode.

Risk

    The driver might not be able to restart the car, and theres a risk that the car could roll away after the driver has left the vehicle not knowing the transmission gear is not in park, according to the NHTSA. The latter could result in personal injury or property damage.

Remedy

    Registered vehicle owners should have received notification of the recall by mail around March 24, 2009. Mailed notifications contained information on where and when to bring the recalled vehicles. Authorized dealers were instructed to inspect the affected vehicles to ensure that the shift cable adjustment clips fully engage and make repairs at no charge.

Read More.. >

Friday, May 2, 2014

What Causes a Lock Up Torque Converter in the Transmission

Theres nothing wrong with a locked-up torque converter; as a matter of fact, lock-up torque converters have been making automatic transmissions more efficient for decades. Youll only encounter brief periods during your driving cycle where converter lock-up is not beneficial.

Converter Operation

    Torque converters are fluid couplers. A turbine fan attached to the outer case (which is bolted to the engine) pushes transmission fluid through a matching turbine on the transmission input shaft. The engine doesnt push enough fluid when idling to engage the transmission turbine. As rpm rises, that fluid will begin to push against and spin the transmission-side turbine, engaging it and moving the car.

The Problem

    Because there was no direct connection between the engine and transmission, a non-lock-up converter will always get worse fuel mileage than a manual transmission, which uses a clutch.

Lock-Up Function

    A lock-up converter uses a clutch pack very similar to those inside the transmission itself to lock the converter case to the transmission input shaft. At about 25 mph, the computer sends a signal to an electronic actuator inside the transmission to engage the clutch pack and lock the drive line together.

Read More.. >

Tuesday, April 29, 2014

What Is a Quick Fix for a Slipping Transmission

What Is a Quick Fix for a Slipping Transmission?

When a transmission is working properly, gears shift smoothly to drive, reverse or park a vehicle. However, sometimes problems occur resulting in a transmission slipping.

Cause

    One of the main causes of a slipping transmission is leaking fluid. Transmission fluid can leak from places such as the driveshaft seals, the torque converter or the pan gasket of the transmission. If the fluid gets really low, the transmission could fail to work altogether.

Check

    A dipstick that indicates low transmission fluid levels could mean fluid is leaking. You need the engine idling with the vehicle in park as you make this check. If there is still no leak to be seen, it may be a leak in the transmission fluid cooler in your radiator.

Fix

    If a leak is not the reason your transmission fluid levels are low, adding back the proper amount is a quick fix for a slipping transmission. The full mark on the dipstick is what should be used to avoid overfilling. Too much transmission fluid added can negatively affect the way a transmission functions.

Read More.. >

Wednesday, April 23, 2014

What Is a VW IRS Transmission

What Is a VW IRS Transmission?

A VW IRS, or Volkswagen independent rear suspension, transmission is a special type of transmission that can be found in several models of Volkswagen automobiles, particularly the Volkswagen Beetle.

History

    The IRS, or independent rear suspension, transmission system was first introduced to the automobile industry in 1968, coming included with the semi-automatic Volkswagen Beetle. In 1969, all Beetles in the United States were fitted with the IRS, and in 1971, other countries followed suit. In the years since then, the IRS has been become an automobile industry standard.

Function

    An IRS is a type of automobile suspension system that allows two rear wheels that are on the same axle to shift position vertically without affecting each others position. The wheels spin in unison with each other, but raising one wheel doesnt lower the other as it would if the wheels were linked.

Benefits

    One of the most important benefits of this type of transmission is that it provides a much safer, smoother ride and better handling. Because the IRS is set up so that the vertical movement of one wheel does not affect the vertical movement of the other, bumps in the road do not cause both wheels to shift.

Read More.. >

Friday, April 4, 2014

Jeep Wrangler Transmission Problems

Jeep Wrangler Transmission Problems

On November 3, 2009, Chrysler LLC and the National Highway Traffic Safety Administration (NHTSA) announced a recall of 88,461 Jeep Wrangler vehicles for transmission problems that could potentially cause a fire.

Defect

    According to Chrysler and the NHTSA, certain model year 2007-2008 Jeep Wranglers manufactured from June 2006 through July 2008 and equipped with automatic transmissions were erroneously not equipped with a temperature warning system.

Risk

    A fire may result if fluid boils over and comes into contact with the hot engine, per the NHTSA. This could cause personal injury to consumers and/or damage to property.

Remedy

    Dealers must inspect and install a "hot oil" message in the instrument cluster and warning chime indicating an elevated transmission fluid condition, according to the NHTSA.

Notification

    Chrysler mailed notification to registered vehicle owners with instructions to bring the affected Jeep Wranglers to authorized dealers for repair in February 2010. Concerned drivers who did not receive notification may contact Chrysler or NHTSA to determine whether their Jeep Wranglers might be subject to these transmission problems.

Read More.. >

Thursday, April 3, 2014

How to Remove the Manual Transmission in a 93 Ford Ranger

Removing the manual transmission from your 1993 Ford Ranger is not a difficult task with the proper preparation, the right tools and a competent helper. The Ranger is identical to the Mazda pick-up so you will need both standard and metric tools because the parts are of mixed origin. You should also have plenty of shop towels or rags to clean up any spills. A handy option to have is an inexpensive transmission plug that can be purchased. You can use a rag instead. Choose a work area that is flat, solid and free from obstructions. Safety first.

Instructions

    1

    Remove the negative battery cable. Put the transmission in neutral. Drain the transmission. Use the floor jack to raise the vehicle high enough to work underneath. Support the truck on jack stands. Test the stability by trying to shake the vehicle. If there is any movement, re-set the stands. Release the emergency brake.

    2

    Locate the factory paint mark at the rear of the driveshaft and corresponding mark on the front of the differential. If you cannot see the marks, make your own using a scribe or some indelible method. These will help you reinstall the shaft and maintain its balance. Remove the nuts securing the rear of the shaft and slide the front spline out of the transmission. Use the plug or a rag to prevent leakage.

    3

    If you have 4WD, remove the transfer case. If you have a V-6, take out the exhaust. Disconnect the hydraulic clutch line, the speedometer cable and the electrical connectors. Label all connections for later installation. Remove the starter. Place the floor jack with a block of wood to protect the oil pan under the engine. Put a little upward pressure on the engine to provide support.

    4

    Place the transmission jack under the transmission and put a slight amount of pressure to support the unit. Disconnect the bolts from the bell housing to the engine. Remove the rear transmission mount. Remove the cross member. Simultaneously release pressure on the transmission jack as you withdraw the assembly toward the rear. Work slowly to free the transmission and gain enough clearance for the input shaft to clear the clutch pressure plate.

Read More.. >

Saturday, March 8, 2014

How to Identify a Borg Warner Transmission

How to Identify a Borg Warner Transmission

Borg Warner started manufacturing the T5 transmission in 1982. Since its inception, the transmission has been placed into various vehicles, including Ford and General Motors models. The five-speed transmissions fall into two categories: world class and non-world class. The T5 is credited as the only American-made manual transmission to be in production for more than 20 years. The Borg Warner T-10 also is a popular transmission, and both have identifying marks.

Instructions

Finding the Identifiers

    1

    Locate the identification tag number. A quick way to confirm that your transmission is a Borg Warner and what vehicle it was designed for, is to locate the identification number stamped into the "metal tag bolted onto the tail housing," according to 5speeds.com. Once you have the identification number you can access one of the two Web listed in the Resources section of this article to find out more information about the transmission. This listing can tell you what transmission you have and what vehicle it was originally designed for.

    2

    Look at the forward shaft bearing/support. Borg Warner transmissions usually a sticker saying Timken with a part number or a yellow and black sticker that says "use Dexron II only," according to British V8 Newsletter. These stickers are most commonly found on Borg Warner transmissions.

    3

    Count the number of bolts on the transmission cover. On the Borg Warner T10 transmission there are nine bolts attaching the side cover. This is only found on the T10.

    4

    Look numbers on transmission housing. You may not need the entire number stamped on the metal tag to determine whether or not you have a Borg Warner transmission. Knowing what numbers mean Borg Warner might save you a trip to the computer. For example, on a Borg Warner T10, the identifiers T-10 and/or 13-04 should be imprinted on the transmission housing. On a T5, the identifier should begin with 13-52. The casing number on a Borg Warner T19 is 1309and the T18 casing number is 1301. Both the T18 and T19 are "top loaded heavy-duty 4-speed transmissions with [a] cast iron case and shift cover," according to motivegear.com.

Read More.. >

Friday, March 7, 2014

Transmission Codes for Chevy Blazers

If your Chevy Blazer is not working correctly, you can use General Motors trouble code numbers to help diagnose the problem. The code numbers are read via a scan tool plugged into the vehicle diagnostic connector under the instrument panel. According to AA1Car, for some code numbers the same number may be used for different faults on different model years or models. After youve figured out the code, further testing must be done before repairs are made, AA1Car warns.

P1500 and P1600 Codes

    P1521 is defined as transmission engaged at high throttle angle. P1527 is transmission range/pressure switch comparison. P1623 is transmission temp pull-up resistor.

P1700 Codes

    P1700 is transmission MIL request. P1701 is transmission MIL request circuit. P1740 is transmission torque reduction request circuit. P1760 is transmission control module supply voltage interrupted. P1792 is ECM to transmission control module engine coolant signal.

P1800 Codes

    P1800 is ECM to transmission control module engine coolant signal. P1812 is transmission over temperature condition. P1815 is transmission range switch-start in wrong range. P1819 is transmission range switch out of range, possible no start. P1820 is transmission range switch A voltage low. P1822 is transmission range switch B voltage high. P1823 is transmission range switch P voltage low. P1825 is transmission range switch A, B, C and P signals invalid. P1826 is transmission range switch C voltage high. P1845 is transmission gear ratio output circuit. P1868 is transmission fluid life. P1870 is transmission component slipping.

Read More.. >

Wednesday, March 5, 2014

How to Remove the Gear Shift on a Manual Transmission Ford F 150

How to Remove the Gear Shift on a Manual Transmission Ford F-150

A Ford F-150s gear shift is simple to remove. It is also a repair procedure that doesnt require disabling the F-150s airbag system, unlike many of the components located in the dashboard. There are two major reasons why you might consider doing this. If youre revamping and customizing the F-150s interior, the shift lever boot, the lever and the knob likely have aftermarket options to consider. On a more pragmatic level, you will need to remove the gear shifter entirely if you are going to access and work on the manual transmission.

Instructions

    1

    Remove the shift boots four retaining screws located at each corner of the boot. You will have to lift up the corner to get at the screws.

    2

    Pull the boot directly upward to expose a nut and bolt on the lever. You do not need to remove the boot completely from the lever. So you can leave the shift knob alone.

    3

    Unscrew the nut with a socket wrench. Then push the threaded side of the bolt through the lever. Grab the bolt by its other side and pull it out of the shift lever.

    4

    Remove the lever from the square mounting boot beneath it.

Read More.. >

Friday, February 7, 2014

Rebuilt Vs Remanufactured Transmission

Rebuilt Vs. Remanufactured Transmission

Rebuilt and remanufactured transmissions are readily available options for most vehicles. However, these terms mean something different, and knowing the differences can make a decision between the two easier.

Rebuilt

    A rebuilt transmission usually is one that has been taken apart, and those components that were damaged or not functioning properly have been replaced. Usually, this is the less expensive of the two options. In this case only damaged or faulty components are replaced. All other components are used again.

Remanufactured

    A remanufactured transmission is one where all vital components have been replaced, and only the cast parts, such as the outer shell, have been reused. These typically are more expensive, since more work has been done to the transmission. Also they tend to be more reliable, as they are nearly new.

The Warranty

    Often, the same warranty will be offered with both types of transmission, although that for the remanufactured unit may be slightly longer. This is because typically if anything that is the fault of the rebuilder or remanufacturing company is going to malfunction, it will do so relatively early in the warranty. However, the longer the warranty, the longer you do not have to worry about replacement cost.

Read More.. >

Monday, February 3, 2014

Tips for Rebuilding a 4L60E Transmission

Tips for Rebuilding a 4L60E Transmission

The 4L60E transmission is an electronically-controlled version of the 700R4 four-speed overdrive transmission. The engine control module controls and shifts the transmission for precise control of the shift points and lockup torque converter. Manufacturers used the transmission in light- and medium-duty rear-wheel drive and four-wheel drive vehicles, such as trucks and sport utility vehicles, and in full-size rear-wheel drive passenger cars such as the Caprice and Impala.

Proper Workbench

    The 4L60E transmission has numerous parts internal to the case assembly. Professional transmission re-builders use a very large worktable with plenty of room to keep the parts in order, clean and organized. The worktables have ledges to prevent losing small parts and components and a screened drain to capture transmission fluid. Lay out the internal components of the 4L60E during disassembly in order on an adequately sized workbench to keep the components organized.

Clean Workspace

    Clean the worktable prior to use. Transmission re-builders worktables are stainless steel and easy to clean. Dirt and grit picked up during the rebuilding process significantly reduce the life of a transmission. In a pinch, secure wood strips around the outside edge of the table to create a ledge to retain small parts. Drape a plastic drop as a resourcecloth over the table to provide a clean surface and catch excess transmission fluid.

Visual Aids

    Obtain an exploded view diagram of the 4L60E from the transmission parts supplier. Suppliers keep diagrams on hand to identify the exact parts customers are attempting to purchase. The diagram indicates the order and placement of the components. Experienced technicians use the diagram while rebuilding to jog their memory and speed the assembly process. Often overlooked as a resource, cell phones can be invaluable during the rebuilding process. Take numerous pictures with a cell phone during the disassembly process as a erence to help during re-assembly of the 4L60E.

Additional Componets to Consider Replacing

    The 4L60E transmission has several known weak points that are prone to failure. Upgrade the sun-reaction shell with a hardened steel sun shell to prevent it from shearing at the splines. Upgrade the 2-4 servo to increase the holding power of the band, preventing slipping and burning of the band. Install a rev-kit or new springs in the 3-4 clutch pack to prevent engagement at high rpm that will burn and damage the new clutch pack.

High Horsepower Modifications

    With proper modifications, the 4L60E transmission will easily handle 600 foot-pounds or more of torque from highly-modified powerful engines. Upgrade the input shaft and output shafts from mild steel to hardened steel shafts. Replace the stock three-gear planetary gear sets with four- or five-gear planetary sets. Use racing clutches, bands and steels. Use synthetic transmission fluid to handle extreme heat and stress and extend the life of the transmission under abusive conditions.

Modifying Shift Quality

    The springs of the accumulators under the valve body of the 4L60 E control the crispness of the shifts. The servos control shift quality by purposefully slowing the buildup of fluid pressure in the clutch servos. The clutches slip, creating a smooth transition into the next gear. Softer springs result in softer shifts. Stiffer springs result in crisper shifts. Install the servo piston and spring in the upside-down position to lock them out completely, for the harshest and crispest shift possible.

Read More.. >

Sunday, January 26, 2014

Automatic Transmission Flush Procedures

Purchasing a brand new transmission could set you back as much as $2,000. Anything that can be done to keep your transmission operating smoothly is highly recommended. A transmission flush is one such task, and having information regarding this topic can be beneficial to vehicle owners.

Procedures

    A transmission flush is the process of replacing old transmission fluid with fresh fluid. Fluid flush machines can be used for this and are known to make the process simple and quick, taking only about 10 minutes or so to complete. The car is put in park and the engine left idling as the old fluid is swapped out for the new.

Significance

    Worn out fluid is harmful to transmissions, often resulting in them failing altogether. Old fluid becomes oxidized and fails to lubricate the transmission as well as it did when it was new. Control valves also stick due to old dirty fluid. A transmission flush eliminates all these harmful effects caused by old fluid.

Time Frame

    Flushing a transmission on a regular basis can increase the life of the transmission. It is recommended to have your transmission flushed about every 40,000 miles or so.

Read More.. >

Friday, December 6, 2013

The Purpose of a Transmission Mount

The Purpose of a Transmission Mount

A transmission mount provides support for the transmission. A transmission mount and a motor mount are essentially identical, but one supports the transmission and the other the engine. Both are often referred to as a motor mount.

Protecting Transmission

    The primary purpose of a transmission mount is to hold the transmission in place and reduce its movements. A transmission that moves too much can cause damage, especially in the linkages between the transmission and the engine and drive shaft. Transmission movements can also damage lines and hoses running from or near the transmission.

Noise and Vibration

    Another purpose of the transmission mount is to reduce the amount of noise and vibration in the vehicle. This is done to make the vehicle drive as smoothly and quietly as possible both for the comfort of the driver and passengers as well as to reduce wear on the vehicle body and suspension.

Design

    Most transmission mounts are simple devices made of two metal plates and a block of rubber. One plate attaches to the transmission and the other to the vehicles body. The rubber block is held between the plates and dampens the transmissions movements. Some transmission mounts are hydraulic, using a hydraulic fluid in place of the rubber.

Read More.. >

Tuesday, December 3, 2013

How to Do a Transmission Flush on an Odyssey

The Honda Odyssey transmission fluid changes color over time due to worn clutch material contaminating the fluid. It is not open to the atmosphere and is not affected by the engine. Any contamination in the transmission is strictly due to internal wear, which is normal. The Odyssey does not have a traditional filter or oil pan on the transmission. It has a large magnetic drain plug, which attracts all metal shavings that must be cleaned before flushing.

Instructions

    1

    Drive the vehicle to a reputable service facility. Instruct the service writer to drain the transmission, and remove and clean all the metal particles off the magnetic drain plug. When this is clean, refill the transmission.

    2

    Instruct the service writer to perform a power flush on the transmission. The reasoning behind this is that it does little good to perform a power flush as long as the magnetic plug is covered with metallic chips. The transmission only gets a flush when the fluid turns from red to brown, which takes a long time. Draining and filling the transmission with fluid does no good, since the majority of fluid is in the torque converter and pump. As soon as the vehicle starts up, the fluid will be dark again. Flushing the transmission involves removing the transmission lines from the radiator and connecting them to a large power flushing machine. The mechanic starts the engine, and the machine forces new fluid into the transmission and pulls the contaminated fluid out until the fluid flows red. This usually requires the machine to dispense about 13 to 18 quarts of new transmission fluid.

    3

    Request the service writer to add a clutch-modifier fluid to the transmission fluid after the flush is complete. This adheres to the clutch discs and creates a rougher surface for better clutch engagement. Now the transmission will shift better and faster. The biggest benefit is that it extends the life of the transmission by at least 40 percent.

Read More.. >

Monday, December 2, 2013

How to Stop a Leak in a Manual Transmission

How to Stop a Leak in a Manual Transmission

Transmission leaks may lead to serious problems for your automobile. Manual transmissions are not forgiving of low fluid levels, and will malfunction within a short time when the fluid levels drop too low. The major causes of transmission leaks are loose nuts and a loose transmission pan or dried out gasket seals. Stop-leak transmission fluids may be useful for your manual transmission, as they condition and repair leaky seals. However, manual transmission fluid leaks are more often caused by loose fittings.

Instructions

Prevent Leaks Through Routine Maintenance

    1

    Prevent transmission fluid leaks through routine maintenance of your automobile engine. Follow the instructions in your automobile manual. Manufacturers of most engines recommend transmission fluid changes every 30,000 miles.

    2

    Drive your automobile for approximately a mile or around the block to warm up the transmission fluid.

    3

    Elevate your vehicle with a jack or put it on a ramp. Make certain the vehicle is secure before working under it.

    4

    Using your wrench or ratchet, remove the outer plug -- if applicable -- and then remove the transmission fluid drain plug. Drain the fluid into a plastic or metal container.

    5

    Clean the drain plug with a clean cloth. The transmission drain plug is magnetic so that it captures small bits of metal as the transmission gears wear. Wipe the plug thoroughly and replace after all fluid has drained out. Tighten the plug.

    6

    Pump new fluid into the transmission through the fill plug. This plug is usually located on the side of the transmission. Use the amount of fluid recommended by your automobile owners manual.

Stop Leaks

    7

    Notice the signs of transmission oil leaks: oil on the driveway, sluggish transmission, low fluid levels as determined by checking with a dip stick.

    8

    Perform routine maintenance when a transmission fluid leak is evident. Drain the fluid from the transmission, according to the previous steps.

    9

    Loosen oil pan bolts with a wrench and remove the pan. Clean the pan with soap and water and wipe dry.

    10

    Spread gasket sealant around the gasket ridge of the oil pan. Make certain sealant is around each bolt hole.

    11

    Press the gasket into place in the sealant on the drain pan. Put bolts through the holes to keep the bolt holes open. Let cure for 30 minutes. Replace the pan. Make certain bolts are tight.

Read More.. >

Sunday, November 10, 2013

Isuzu Rodeo Transmission Problems

Isuzu Rodeo Transmission Problems

Japanese automaker Isuzu Motors Ltd. had the Rodeo pick-up truck built and sold in the United States from 1991 to 2004. Never the most reliable vehicles on the market, the earlier versions of the Isuzu Rodeo has a common problem concerning the transmission.

Problem


    Some Isuzu Rodeos may experience failure of the force motor. This component is essential to the shifting components of the transmission; its malfunction may thus cause the transmission to have problems with shifting gears.

Affected Models and Transmissions

    The earlier models of the Isuzu Rodeo -- specifically, of the 1991 to 1995 model years -- suffer from this problem. Also, the force motor failure is restricted to the vehicles alternative four-speed automatic transmission, the 4L30-E from General Motors. The standard three-speed manual gearbox is not afflicted by this issue.

Cost of Repair

    As of December 2010, customers would need to pay about $189 for parts and $208 for labor to get the force motor fixed. The aforementioned prices are estimates based on an $65 hourly rate, excluding diagnostic time and tax.

Read More.. >

Wednesday, October 16, 2013

How Much Does a Transmission for a 1989 Toyota Camry Cost

The cost of a transmission for any vehicle is high, and the Toyota Camry is no exception. Make sure to survey your options before deciding to replace it. Transmission prices vary greatly from area to area.

Rebuilt Transmission

    A rebuilt or remanufactured transmission can be purchased in the range of $1,300 to $1,600 and possibly higher. The price increases steeply with longer warranties; for example, a five-year warranty can add $1,500 to the cost of the transmission.

Used Transmission

    A salvaged or used transmission could be a more economical option. The prices vary depending on original car source, age of the transmission and location. However, the price can be lower than the price of a rebuilt transmission -- even as low as $500.

Transmission Repair

    The cost of repairing a transmission is high, but the price depends on how much work needs to be done. The cost of an internal problem is high no matter how small the problem; taking apart and reassembling a transmission is expensive. The repair can cost anywhere from $1,800 to $3,600. Before you go that route, request diagnostics to determine more about the damage and ultimate price of the repair.

Read More.. >