Wednesday, August 27, 2014
Jeep Cherokee Parking Brake Lever Removal
The brake lever sits in the center console of the Jeep Cherokee. The emergency brake cable runs under the Jeep and attaches from the bottom side, joining the two rear cables with the single front cable. While failure of the lever assembly is not common, the ratcheting gears inside the handle and the locking mechanism can fail. Those parts cannot be serviced individually. You have to replace the entire assembly to fix a problem with the lever or the components inside it.
Instructions
- 1
Raise the front of your Cherokee off the ground with a jack. Position a set of jack stands under the frame to support the Jeep. Slide under the Jeep and locate the parking brake equalizer, which is directly under the parking brake lever.
2Remove the nut from the tension rod with a wrench. Slide the equalizer off the tension rod. Remove the front cable from the tension rod and lay it aside. Slide out from under the Jeep. Open the passengers door so you can access the center console and the brake lever.
3Open the center console. Locate the two screws at the top edge of the trim panel that extends from the top of the console to the front of the brake lever cutout. Remove the screws with a Phillips screwdriver.
4Pull the brake handle up then lift the rear of the trim panel up several inches. Slide the trim panel back to release it from the front of the center console and lift it off the brake lever.
5Locate the electrical connector on the brake lever switch near the bottom of the brake handle assemble. It is on the drivers side near the back of the assembly. Pull the connector off the switch and set the connector aside.
6Remove the two retaining bolts from the brake handle assembly with a socket and ratchet. Lift the assembly out of the console and remove it from the Jeep.
Sunday, May 11, 2014
How to Install a Jeep Power Tech 2 4L Oil Pump
Chrysler has used the PowerTech brand for a variety of unrelated engines. One type of PowerTech engine is a four-cylinder 2.4-liter engine that appeared in the Jeep Liberty from 2002 to 2005. The oil pump on this vehicle circulates oil throughout the engine to provide lubrication for its moving parts. The Jeep PowerTech 2.4-liter engine has its oil pump on the crankshaft sprocket in front of the engine.
Instructions
- 1
Remove the cable from the negative terminal of the battery with a socket wrench. Disconnect the rear cover of the timing belt and loosen the timing belt tensioner. Detach the timing belt.
2Disconnect the mounting bolts for the oil pan with a socket wrench. Remove the oil pan from the engine.
3Remove the crankshaft sprocket with Special Tool 6793 and Special Tool C-4685-C2. Disconnect the crankshaft key with a socket wrench and detach the oil pick-up tube from the oil pump. Remove the oil pump and the crankshaft seal from the crankshaft sprocket. Discard the crankshaft seal.
4Clean the mounting surfaces for the new oil pump with a shop rag and apply gasket sealer to the mounting surfaces. Install the O-ring into the discharge passage of the oil pump. Fill the oil pump with engine oil to prime it.
5Align the rotor flats of the oil pump with the crankshaft flats. Install the oil pump to the block with a new crankshaft seal. Connect the crankshaft key with a socket wrench. Install the crankshaft sprocket with Special Tool 6792 to set the sprocket to the original depth.
6Connect the oil pump pick-up tube to the oil pump. Mount the oil pan and fasten the mounting bolts with a socket wrench. Install the timing belt and connect the rear cover for the timing belt with a socket wrench.
Saturday, May 3, 2014
Jeep Commander Electrical Problems
Electrical problems in Jeep Commander vehicles have led to recalls by Chrysler and the National Highway Traffic Safety Administration (NHTSA) in 2008, 2009 and 2010. Registered vehicle owners should have received notification from the manufacturer with instructions on where to bring the recalled Jeeps for free repair.
WIN Module Defect
On May 6, 2010, Chrysler recalled 40,131 vehicles, including 2010 model year Jeep Commanders, for a Wireless Ignition Node (WIN) module exhibiting a binding condition of the solenoid latch. It is possible to remove the key from the modules ignition switch before the shifter goes into "park" mode, which may allow the vehicle to roll away and cause a crash.
Airbag Wiring Defect
On April 7, 2009, Chrysler recalled 4,314 vehicles, including certain 2009 Commanders, because a wiring defect may cause the drivers side airbag not to work properly. During manufacturing, the wiring was inadvertently reversed on the steering column control module driver airbag squib connector.
Front Control Module Defect
On February 5, 2008, Chrysler recalled 1,338 Jeeps, including 2008 Commanders, for a manufacturing defect in the front control module that could cause the engine to stall while driving or not to start. The electrical problem may cause the windshield wipers to stop working properly.
Saturday, April 5, 2014
How to Install Weatherstripping on a Jeep Cherokee
You can install weatherstripping on your Jeep Cherokee in your garage with a few supplies that can be purchased at an auto parts store. Replacing the weatherstripping on a Jeep Cherokee improves the seal formed between the door frame and the closed vehicle door. Weatherstripping prevents air and moisture from entering the Jeep and ruining the interior. You will know its time to install new weatherstripping when the old weatherstripping becomes cracked, loses its shape and wont seal the door properly.
Instructions
- 1
Find the clips that secure the weatherstripping to the Jeep. Remove them with needle-nose pliers. Place the clips in a cup and set aside.
2Pull the old weatherstripping off of the Jeep with your hands. Each piece of weatherstripping will slide right off the door frame channel.
3Wipe degrease agent with a rag onto the door frame weatherstripping channel. This will remove all the grease and dirt.
4Slide new weatherstripping onto the channel on the door frame.
5Reattach the clips to the weatherstripping, pushing them over the top of the stripping and attaching them to the Jeeps door frame. You will hear them snap into place when properly attached.
Friday, April 4, 2014
Jeep Wrangler Transmission Problems
On November 3, 2009, Chrysler LLC and the National Highway Traffic Safety Administration (NHTSA) announced a recall of 88,461 Jeep Wrangler vehicles for transmission problems that could potentially cause a fire.
Defect
According to Chrysler and the NHTSA, certain model year 2007-2008 Jeep Wranglers manufactured from June 2006 through July 2008 and equipped with automatic transmissions were erroneously not equipped with a temperature warning system.
Risk
A fire may result if fluid boils over and comes into contact with the hot engine, per the NHTSA. This could cause personal injury to consumers and/or damage to property.
Remedy
Dealers must inspect and install a "hot oil" message in the instrument cluster and warning chime indicating an elevated transmission fluid condition, according to the NHTSA.
Notification
Chrysler mailed notification to registered vehicle owners with instructions to bring the affected Jeep Wranglers to authorized dealers for repair in February 2010. Concerned drivers who did not receive notification may contact Chrysler or NHTSA to determine whether their Jeep Wranglers might be subject to these transmission problems.
Friday, March 7, 2014
My Jeep Wont Crank
Cranking means that a vehicles engine will turn over and eventually start. The term comes from the cranking amps that are described on batteries. These numbers will vary by battery and vehicle. If your Jeep is not starting, there are a few potential reasons that you can examine and troubleshoot yourself. Some problems will require a professional in order to do the work correctly.
Instructions
- 1
Lift the hood of the Jeep. Sometimes, the Jeep will not crank because the battery leads and cables are dirty or corroded. You may notice a creamy green and white coloration on the battery that looks like baking soda. This is actually blocking the battery from sending power to the starter. Remove the cables and polish the battery with the wire brush. Tighten them with the wrench. Try starting the Jeep.
2Jump-start the jeep with another car and your jumper cables. Remember to place red on red and black on black when you are placing the cables. Turn the key. If the engine is whirring but still not turning over, you may need a new battery.
3Take the battery out by removing the two nuts on the top of the battery. Your local auto parts store can check the battery and give you a print out stating if you need a new battery. If you need a battery replace it and install it in the Jeep. Try starting the Jeep. If it is not starting you may have another problem.
4Listen for a whirring sound. If you are getting a whirring sound you may have a grounding problem somewhere on the vehicle. Check the wire leads around the alternator. The alternator is located near the battery on the top left of the engine as you are looking at it from the front bumper. It will have a pulley and a belt around it. If there are no loose wires or frayed wires, then you may have a bad alternator that is not transferring power back to the battery.
5Listen for a clicking sound. Lack of a whirring sound, along with the presence of clicking sound, means that you have a bad starter solenoid. This will require a professional mechanic to replace.
Wednesday, March 5, 2014
How Often Should You Service a Jeep Compass
Like most vehicles, it is suggested that the Jeep Compass be serviced every 3,000 miles. The Jeep indicator message on the dashboard lights up at 2,500 miles to warn the driver that the car will soon need service.
Identification
Jeep provides owner manuals to all Jeep owners. The manual suggests vehicles be serviced every 3,000 miles if the vehicle is falls under any of the following categories: Day or night temperatures are below 0 C, stop-and-go driving, extensive engine idling, driving in dusty conditions, short trips of less than 10 miles, trailer towing, taxi, police, or delivery service (commercial service), off-road or desert operation, and/or heavy loading.
Resetting Indicator
Because the message indicator illuminates to warn the driver to schedule service, it must be reset once the vehicle is serviced. If the service is pormed by the owner, it must be reset manually so the driver can be reminded of future maintenance needs.
Considerations
Service at 3,000 miles is only a suggestion. To ensure safety, service your vehicle according to your driving habits.
Monday, February 17, 2014
How to Replace Jeep Liberty Tail Lights
The tail lights on the Jeep Liberty are enclosed in a plastic assembly with the bulbs mounted inside. To access the bulbs, you must first remove the assembly from the Jeep, but you can remove it in a few minutes with basic hand tools. The bulbs used in the tail light are standard 3057 bulbs, available at any auto parts store. These bulbs have a dual filament so they operate both the brake and tail lights.
Instructions
- 1
Open the lift gate of your Jeep and locate the retaining screws along the inner edge of the tail light assembly. Remove the screws with a socket and ratchet and set them aside.
2Separate the tail light assembly from the rear of the Jeep and locate the electrical connector on the rear of the assembly. Depress the locking tab and pull the connector away from the tail light back plate.
3Remove the two screws that hold the back plate to the tail light assembly with a Phillips head screwdriver then separate the back plate from the tail light. Grasp the bulb and pull it straight out of the back plate. Discard it.
4Install a new 3057 bulb into the back plate, pushing it in until it seats firmly in the socket. Install the back plate on the rear of the tail light assembly then install the two retaining screws and tighten them with the Phillips head screwdriver.
5Position the tail light assembly on the rear of the Jeep, install the retaining screws and tighten them with a socket and ratchet. Do not over-tighten these screws or you will crack the plastic assembly. Close the lift gate and test the light by turning on the head light switch.
Thursday, January 30, 2014
Jeep Steering Problems
Steering problems in Jeeps have led to multiple recalls by Chrysler. Jeep Grand Cherokee, Commander, Liberty and Wrangler vehicles were recalled in 2008 and 2009. According to the National Highway Traffic Safety Administration (NHTSA), registered vehicle owners should have been notified by mail about these recalls.
Steering Capability Loss
On April 7, 2009, Chrysler recalled 43,489 2002 and 2003 Jeep Liberty vehicles because the front suspension upper control arm ball joint might not be properly lubricated and might corrode. This could lead to a loss of steering capability, according to the NHTSA.
Steering Intermediate Shaft
On May 5, 2008, Chrysler recalled 1,585 Jeep Wranglers with the model years of 2007 and 2008 because some of these Jeeps might have been manufactured with insufficient clearance between the steering intermediate shaft and the rear brake tubes. Per the NHTSA, prolonged brake tube contact could wear a hole in the tube and lead to partial brake system loss.
Steering Column Wiring
On April 7, 2009, Chrysler recalled 4,314 Jeeps vehicles including Grand Cherokee, Commander and Wrangler 2009 models due to reversed wiring in steering column. The wiring problem could keep the drivers side air bag from working in a crash.
Friday, January 17, 2014
How to Change the Exhaust on a Jeep
Historically, the Jeep is known to have been one of the first off-road vehicles on the front lines of many wars. The technology that made this vehicle a star player on the battlefield makes it desirable for adventurous drivers today. The Jeep 4.0-liter engine and exhaust package can deliver speeds fit for modern highways, but it can also deliver the torque to drive through rough terrain. If this legendary drive train has a weakness in design and material it would have to be the 4.0-liter factory header and exhaust package. Numerous owner complaints of leaky headers and manifolds should alert you that when purchasing a used Jeep you should consider these tips on how to change the exhaust on a Jeep.
Instructions
- 1
Drive the vehicle onto two automotive ramps and park it so that both front tires are sitting in the middle of the top of each vehicle ramp. Engage the parking brake and place blocks behind the rear wheels before beginning to work. Raise the hood and disconnect the positive cable from the battery and secure it away from its positive post.
2Use a screwdriver to loosen the air tube from the throttle body. Pull the tube free and move it away from the work area. Disconnect the two vacuum tubes that exit the valve cover and keep them with the air tube assembly. Pliers and/or a screwdriver work well together to pull these hoses free.
3Loosen and remove the bolts securing the fuel rail and fuel line. Many bolts in the Jeep are metric, as are these fuel rail bolts. Once the bolts are removed you can adjust the position of the fuel line and rail to a place that is out of the way of the exhaust manifold.
4Disconnect the cables that enter and exit the intake manifold near the throttle body. These cables include the throttle cable and tans pressure cable. Models with cruise control include a cable for that too. Move all the disconnected equipment to the far side of the engine bay. Tie back with plastic tie straps to keep from falling into your work space.
5Remove the protective cover inside the front wheel well that is nearest the exhaust manifold. Without this protector, the wheel well allows access to the header pipe and fasteners. From here you will remove the oxygen sensors that are inserted into the manifold and header pipe. Move the sensors to the far side of the engine bay and continue.
6Disconnect the header pipe from the manifold. Move to the back of the catalytic converter and separate the catalytic converter and header pipe from the rest of the exhaust at the back of the Jeep. Pull the rest of the exhaust out of place by pulling the exhaust hangers free from the old exhaust, then use your reciprocating saw to cut portions of the exhaust apart for easier removal. Never cut or damage the old exhaust hangers as they will be used to hang the new cat-back exhaust.
7Soak the exhaust manifold bolts for at least 20 minutes with penetrating oil. Begin to work the exhaust manifold bolts loose. Loosen the ones that come free easily and then continue to work the hard-to-remove ones with extra oil until they are all free. With all the bolts removed, begin tapping the manifold with a hammer until it breaks free from the engine. Pull the manifold out of the engine bay and clean the surface of the engine where the new manifold will go.
8Install the new exhaust manifold with the gasket sitting between the engine and the manifold. Tighten all the bolts securely using a torque wrench set to 35 foot-pounds of pressure. Apply anti-seize compound on the manifold studs to allow for easy removal in the future. Once the new manifold is installed you can begin to reconnect the header pipe, oxygen sensors, throttle cable, transmission pressure cable, and air tube to their original locations using care to tighten each fitting correctly.
9Hang and connect a new cat-back exhaust system using the original exhaust hangers and the flange that lets it connect to the existing catalytic converter. Run the new tail pipe and position the new muffler in place. Hang the parts using the factory exhaust hangers and tighten together with provided exhaust straps, then secure the exhaust pipe to the catalytic converter flange. With all the pieces together you have changed the exhaust on a Jeep and can expect improved performance and sound from a high-quality exhaust manifold and cat-back exhaust upgrade.
10Connect the positive cable to the battery and close the hood. Drive the vehicle off the automotive ramps and test drive the new exhaust system you have installed. Expect to tighten fittings and fasteners again after the test drive to seat all these nuts and bolts securely.
Monday, December 23, 2013
How to Change Jeep Liberty Oxygen Sensors
The modern car or truck has lots of sensors to tell the vehicles computer how the engine is running, and tune accordingly. One of these is the oxygen or O2 sensor, which detects the amount of oxygen in the vehicles exhaust system and adjusts the fuel/air ration at the heads accordingly. If these sensors go out, youll see a "check engine" light on your dash until theyre replaced, and your Jeep Liberty will run sluggishly. This isnt a fun job, but it can be done in about an hour with the right tools.
Instructions
- 1
Lift up the vehicle using the jack and place it on jack stands. Make sure the vehicle is secure before you crawl underneath it.
2Locate the O2 sensors on the exhaust. Theyre about 2 inches long, and have a wire pigtail sticking out of the end. These are also the only sensors on the exhaust, and the only wiring thats near the exhaust at all.
3Unplug the O2 sensor from the vehicle wiring harness using your hands.
4Remove the O2 sensor using the 3/8-inch ratchet and the oxygen sensor socket. Then thread the replacement O2 sensor in place and tighten it down using the 3/8-inch ratchet and the oxygen sensor socket.
5Plug the O2 sensor back into the stock harness using your hands. Repeat the process for the other O2 sensors in the exhaust, then lift the vehicle back up and remove the jack stands using the jack.
Sunday, December 22, 2013
How to Repair a Jeep Cherokee Liftgate
After years of constantly being opened and closed, the liftgate on a Jeep Cherokee will begin to wear out. The liftgate is supported by two hydraulic arms to keep the door in the air when opened. Occasionally these will begin to wear out causing the door to fall down. The locking mechanism on liftgates will often "dry out" and becoming stuck, preventing you from opening and closing the door. Both repairs should be done at the same time to ensure proper opening, closing and locking of the liftgate for years to come.
Instructions
- 1
Pull the rear seat release straps and move the rear seat forward. Climb inside of the rear cargo area. Using a screwdriver, remove the retaining screws from the lock assembly molding located at the bottom of the liftgate.
2Lift the threaded latching bolt -- it has a green plastic tab located on its base -- by using a set of pliers. Pull until you hear the liftgate pop open. Slide the green plastic tab to the left, and it will snap off the latching bolt. Adjust the latching bolt to the position needed to freely open and close the liftgate. Replace the green plastic tab back onto the bolt. Spray all moving parts of the lock and latch assembly with the aerosol lubricant. Wipe clean with a shop towel. Replace the liftgate trim, and tighten bolts with screwdriver.
3Open and fully extend the liftgate with a friend supporting it in the air. Using a screwdriver, remove the old support bolts from the liftgate and vehicle until the support arm comes free. Place the new support arm where the old support arm was removed from and insert support arm bolts to keep it in place. Use the screwdriver to tighten all support arm bolts. Lower the liftgate to ensure alignment, and adjust if needed.
Wednesday, December 11, 2013
2001 Jeep Recalls
Jeep had several recalls on various 2001 models, including the Wrangler, Cherokee and Grand Cherokee. Most of these recalls were for similar defects across all models, but some recalls were for problems found on particular Jeep vehicles. Two of the largest recalls came on all three Jeep models, affecting more than 1 million vehicles.
Jeep Wrangler
The 2001 Jeep Wrangler was one of the models that was recalled for child-seat and fuel-injection problems. These two recalls were part of the 1 million Jeeps recalled by the manufacturer, and were two of seven problems found on the Wrangler. A child-seat could not be anchored properly to the Wranglers seats according to Federal Motor Safety Standards requirements. The Wrangler was also part of the massive recall of Jeeps for an exhaust and manifold problem concerning the fuel-injection system. The intake of the manifold was allowing debris to accumulate in the engine, which could result in a fire. The 2001 Jeep Wrangler was also recalled for problems with the fuel pump, ignition switch, exterior lighting problems, master cylinder problems and roof-rack latches.
2001 Jeep Cherokee
There were eight different recalls issued for the 2001 Jeep Cherokee. Two of the recalls were part of the 1-million vehicle recall that was seen on the Wrangler and Grand Cherokee concerning the child seat and manifold. Four other recalls on the Cherokee were for problems with the exterior lighting. All four of the exterior-lighting recalls dealt with insufficient illumination of the headlights and reflectors on the Cherokee. Another problem with the Cherokee concerned the master cylinder leaking brake fluid. The internal seal on the master cylinder was losing flexibility in low temperatures, causing brake fluid to leak. The last recall on the Jeep Cherokee was for the plastic grommet on the fuel pump. This grommet connector degraded or corroded, because it was not compatible with gasoline. This caused the grommet to degrade to the point of leaking gasoline.
2001 Jeep Grand Cherokee
Ten different recalls were issued for the 2001 Jeep Grand Cherokee. Eight dealt with the same problems seen in the Wrangler and Cherokee, including the child-seat and fuel-injection problems, but two were different. One of the recalls was for only 626 Grand Cherokees concerning the steering gear box. A nut was coming loose, causing the steering wheel to lock. The other recall, which was different than the other Jeep recalls, was for Grand Cherokees equipped with heated seats. The heating elements were overheating to the point where they could create a fire hazard or burn the passenger.
Tuesday, December 10, 2013
How to Replace Jeep Muffler Tail Pipe
If you take your Jeep Wrangler off road often, rust problems can develop on your exhaust system due to water and moisture. Whether you are replacing your exhaust with an aftermarket kit or a factory system, the process is virtually the same. Exhaust kits may be purchased at any local auto parts store and installed yourself using simple tools. Eye protection must be worn to protect against falling debris.
Instructions
Removal of Stock Exhaust
- 1
Cut the exhaust pipe directly behind the muffler using a hack saw.
2Remove the bolts on the flange that connects the muffler to the catalytic converter using a ratchet and socket. Remove the muffler from the vehicle.
3Remove the stock tailpipe hangers off the factory mounts located on the frame by pulling them out of the rubber bushings with your hands.
4Pull the stock tailpipe out of the vehicle.
Installation of New Exhaust
- 5
Slide the tailpipe hangers into the stock bushings located on the frame.
6Lift the muffler into position. Slide one end into the tailpipe.
7Install the flange onto the catalytic converter and tighten the bolts using a ratchet and socket.
8Place the exhaust clamp that came with the kit over the muffler and tailpipe connection. Tighten the bolts using a ratchet and socket.
9Start the vehicle and check for leaks in the system.
Tuesday, November 26, 2013
How to Adjust Cruise Control on a Jeep CJ7
If you spend a lot of time driving on the highway, you probably are familiar with your cars cruise control. It can make driving long distances more comfortable and increase your fuel economy. Older vehicles with mechanical cruise controls occasionally require adjustments to keep them operating at peak efficiency. If your Jeep CJ7s cruise control engages at a higher or lower speed than youve selected, follow the procedure outlined below.
Instructions
Speed-centering Adjustment
- 1
Locate the cruise-control module underneath the instrument panel on the drivers side. On one side near the mounting tabs are two adjustment screws.
2Adjust the screw closer to the mounting tabs in the following manner: If the cruise control engages two or more miles per hour faster than the selected speed, turn the adjusting screw counterclockwise a quarter-turn. If the cruise control engages two or more miles per hour slower than the selected speed, turn the adjusting screw clockwise a quarter-turn.
3Drive the vehicle on a level road to check for proper adjustment. Repeat the steps above as necessary.
Tuesday, November 19, 2013
How to Get a New Jeep Commander Key
You have to replace your tires, you have to change your oil and you occasionally might have to replace other parts of your Jeep Commander, but the need to replace your keys probably never occurred to you as a possibility. Unfortunately, car keys do get lost on occasion and you might find yourself in need of a new set of car keys. Fortunately, both Jeep dealerships and professional locksmiths can replace your Commanders keys in a timely fashion.
Instructions
- 1
Find the vehicle identification number (VIN) of your Commander. The VIN is located on the engine, on the inside of the drivers door panel and on the bottom left side of your windshield. You can also find your VIN in your purchase paperwork, insurance paperwork and your title or registration paperwork.
2Contact your local Jeep dealership or any professional locksmith. Give them the VIN to your Commander. The VIN holds information for your specific Commander that you will need to have a replacement key made. Commander keys have internal computer chips that are linked to their specific car, and your replacement key will need to be programmed by the Jeep dealer or locksmith to respond to your Commander.
3Visit the Jeep dealer or locksmith. Locksmiths can come to you if you dont have transportation to their offices or to your Jeep dealership. Wait while your car key is made and programmed and pay the fee for the services provided to you.
Thursday, October 31, 2013
How to Replace a Front Sway Bar on a Jeep Wrangler
The sway bar or stabilizer bar on the front of the Jeep Wrangler is in place to keep the body from rolling on the suspension and improve the handling of the Jeep. You can replace the sway bay if necessary; replacement sway bars are available from Jeep and some auto parts stores. The sway bar on the front of your Jeep Wrangler runs over the top of the frame, making access to the mounting hardware much simpler than on other vehicles.
Instructions
- 1
Use a lug wrench to loosen the lug nuts on the front wheels, then raise the front of the Jeep off the ground with a jack. Position a set of jack stands under the front axle of the Jeep to support it, then remove the front tires and set them aside.
2Locate the nut on the top of the stabilizer bar end link near the front coil spring. Use a wrench to remove the nut from the top of the end link and set it aside. Repeat on the opposite side of the Jeep, then lift the sway bar off the end links.
3Move to the front of the Jeep and use a socket and ratchet to remove the four retaining bolts that secure the plastic valance on the frame just behind the bumper. Remove the valance to expose the sway bar bushings and mounts on top of the frame.
4Use a ratchet and socket to remove the four bolts that hold the sway bar mounts to the frame. Lift the U-shaped retainers off the sway bar and set them aside. Lift the sway bar off the frame and remove it from the truck. Slide the bushings off the old bar and save them.
5Slide the bushings onto the new sway bar after applying a small amount of grease to the inside of the bushing. Position the bushing and bar on the frame and install the U-shaped brackets over the sway bar and bushings.
6Use a socket and ratchet to tighten the four retaining bolts. Install the plastic valance, tightening the retaining bolts until they are snug. Be careful not to crack the plastic valance.
7Slide the sway bar onto the top of the end links near the coil spring on both sides of the suspension and thread the retaining nuts onto the top of the link. Torque the bolts to 45 ft.-lbs. with a torque wrench.
8Install the front wheels and thread the lug nuts onto the wheel studs. Raise the front of the Jeep off the jack stands, then remove the stands from under the Jeep. Lower the jack until the tires are on the ground. Tighten the lug nuts with a lug wrench.
Friday, October 11, 2013
How to Make an 89 Jeep Wrangler Fuel Efficient
The 1989 Jeep Wrangler has several attractive features. Unfortunately, excellent gas mileage is not one of them. Through troubled economic times, most Jeep Wrangler owners have had to compensate for this flaw by adopting some new driving practices, in an effort to increase overall fuel efficiency. Aside from making these changes, there are some products you can use to build and support engine performance, in turn helping the fuel burn more efficiently in your Jeep Wrangler.
Instructions
- 1
Pour a commercial fuel additive into your gas tank to clean out the combustion chambers in the engine.
2Pour the oil additive into the oil filler cap on the engine to lubricate and rejuvenate the engine.
3Replace the air and oil filters according to the instructions provided in your repair manual. Have regular tune-ups performed on the engine, and closely monitor your tire pressure.
4Drive in low gears and avoid the use of four-wheel drive.
5Roll down your windows rather than using the air conditioning.
Thursday, October 10, 2013
How to Remove the Oxygen Sensor in a 2002 Jeep Grand 4 0L
In 1993, Jeep upped the ante in the SUV market by releasing the Grand Cherokee, a more luxurious mid-sized SUV. The 2002 Grand Cherokee came standard with a 195-horsepower, 4.0-liter in-line six-cylinder engine. Being an in-line-six engine, federal emission regulations require just two oxygen sensors, one upstream and one downstream. Replacing the two oxygen sensors in a federal emission-compliant 2002 Jeep Grand Cherokee is a straightforward process, but it may require additional heat for those hard-to-remove sensors.
Instructions
Upstream Sensor Removal Bank 1, Sensor 1
- 1
Park the Grand Cherokee on a flat surface and allow it to sit until the engine is completely cool. Allow the vehicle to sit for an additional hour to let the exhaust pipes cool.
2Lift the front of the Grand Cherokee with a floor jack and slide jack stands under the frame rails. Lower the SUV onto the frame rails.
3Crawl under the front of the Jeep until you have a good view of the bottom of the down pipe the pipe that bolts to the exhaust manifold. Find the upstream oxygen sensor screwed into the bottom of the exhaust manifold, near the front of the transmission.
4Trace the sensors wiring until you reach where its harness connects to the Grand Cherokees harness. Unplug the oxygen sensors wiring harness from the Grand Cherokees wiring harness.
5Unscrew the oxygen sensor from the exhaust down pipe, using a ratchet and oxygen sensor socket. If the sensor is seized, heat its base with a propane torch, then loosen it. Once the sensor cools, unscrew the sensor from the pipe.
Upstream Sensor Installation Bank 1, Sensor 1
- 6
Thread the new oxygen sensor into the down pipe by hand, then tighten it to 22 foot-pounds with a torque wrench and socket.
7Connect the oxygen sensors wiring harness to the Grand Cherokees harness.
8Raise the SUV off the jack stands and remove the stands. Lower the vehicle to the ground.
Downstream Sensor Removal Bank 1, Sensor 2
- 9
Lift the front of the Grand Cherokee off the ground with a floor jack and position jack stands under its frame rails. Lower the vehicle onto the jack stands.
10Position yourself under the vehicle, just behind the transmission and toward the passengers side. Find the catalytic converter, the muffler-like component attached to the exhaust pipe. Find the downstream oxygen sensor, which screws into the exhaust pipe right after the catalytic converter.
11Trace the downstream oxygen sensors wiring upward until you find where it connects to the Grand Cherokees wiring harness. Unplug the oxygen sensors wiring harness from the Grand Cherokees harness.
12Remove the oxygen sensor by unscrewing it from the exhaust pipe, using a ratchet and oxygen sensor socket. If the sensor is seized, heat its base with a propane torch, then loosen it. Allow the sensor to sit until it is cool, then continue removing it.
Downstream Sensor Installation Bank 1, Sensor 2
- 13
Thread the new oxygen sensor into the exhaust pipe by hand, then tighten it to 22 foot-pounds with a torque wrench and oxygen sensor socket.
14Connect the oxygen sensors wiring harness to the Grand Cherokees wiring harness.
15Lift the SUV off of the jack stands and remove the stands. Lower the vehicle to the ground.