Showing posts with label 4. Show all posts
Showing posts with label 4. Show all posts

Sunday, January 19, 2014

How to Change the Exhaust Manifold Gasket in a F150 4 6L Engine

The Ford F150s history spans back to the 1948 Ford F-1 half-ton pickup. In 1975, the F-150 was released as a bridge between the F-100 and F-250. The F-150 replaced the F-100 as the smallest of the F-series pickups in 1984. In 1997, Ford dropped the 5.0-liter engine and replaced it with the 4.6-liter V-8, which remained until the 2010 model year. The exhaust manifold gasket is the gasket that seals the connection between the exhaust manifold and the engine. When this gasket fails, it not only creates an exhaust leak, but it can also create a poor running condition.

Instructions

    1

    Loosen and remove the the EGR valve tube, only on the left exhaust manifold, with a combination wrench. Trace the oil dipstick tube downward and locate the point where its bracket bolts to the engine block. Loosen the bolt securing the bracket to the block, with a ratchet and socket, and pull the tube and dipstick from the engine.

    2

    Remove the nuts securing the exhaust manifold to the engine, using a ratchet and socket. If the nuts are frozen, apply a coat of rust penetrating spray to free them. Pry the manifold from the engine, using a 12-inch pry bar. Secure the manifold away from the engine using a bungee strap.

    3

    Pull the old manifold gaskets from the 4.6-liter. Use a wire brush to clean the gasket mating surface on both the exhaust manifold and the engine.

    4

    Place the new gaskets on the manifold studs protruding from the engine block. Each side of the 4.6-liter has two gaskets, one front and one rear.

    5

    Release the exhaust manifold from the bungee strap and place it on the studs protruding from the engine block. Hand-tighten all of the nuts to secure the manifold in place.

    6

    Tighten the nuts, in a crossing pattern starting from the upper rear bolt, to 13 to 16 foot-pounds of torque, using a torque wrench and a socket.

    7

    Place the dipstick tube back into the engine and tighten the bracket bolt with a ratchet and socket.

    8

    Reconnect the EGR valve tube to the exhaust manifold, if applicable, and tighten it to 26 to 33 foot-pounds with a torque wrench and combination wrench.

Read More.. >

Thursday, November 14, 2013

How to Replace the Oxygen Sensor in a 2002 Dodge RAM 4 7

The oxygen sensors on a 2002 Dodge Ram 4.7-liter engine regulate the amount of oxygen burned in the engine, and they improve fuel efficiency and reduce pollution. Over time, the Rams sensors can become ineffective, causing the Dodge to have poor fuel economy and produce excess pollution. The 2002 Dodge Ram 4.7-liter engine has two oxygen sensors, and replacing them when necessary can make your truck more fuel-efficient.

Instructions

    1

    Locate the Rams oxygen sensors. They are located on either side of the catalytic converter on the exhaust system, and they look similar to a spark plug with an electrical wire at the end.

    2

    Remove the Rams wiring harness. Pull off the wire at the end of the pickups oxygen sensors. Do not damage the end of the wire harness.

    3

    Remove the Rams oxygen sensors from the exhaust system, using an oxygen sensor wrench.

    4

    Apply anti-seize compound to the threads of the oxygen sensors and the threads into which they connect.

    5

    Insert the new oxygen sensors, using a wrench to tighten them onto the Rams exhaust system. Reconnect the wiring harness to the oxygen sensors by pressing firmly until they click into place.

Read More.. >

Tuesday, October 22, 2013

The Best Spark Plugs for a Ford 5 4 Engine

The Best Spark Plugs for a Ford 5.4 Engine

Frustration surrounds the Ford 5.4 Triton Engine. First, Ford had problems, according to Consumer Affairs, when the 5.4-liter engine blew spark plugs out of the head. Then, models from 2004 to 2008 were affected by spark plugs that were hard to remove and broke off in the head, according to Ford Technical Service Bulletin (TSB) 8-7-6. This affects all Ford and Lincoln Mercury vehicles with the 5.4-liter engine. The best spark plugs to install for the 5.4-liter Triton engine resist carbon buildup, are durable and come in one-piece.

Motorcraft

    The new Motorcraft spark plug for the 5.4 Triton engine, the MC SP507 platinum plug, replaces the old plug, PZT14F. The SP507 is one piece and has a little more durability. The design prevents fouling at low engine speeds, and is self-cleaning at high engine speeds. The old PZT14F was designed in two pieces, and would have a tendency to break off in the head due to carbon buildup on the seat. The newer plug tends to be more durable in the torque stress. The lack of carbonization buildup with the newer model aids in removing used spark plugs. This spark plug was made for the Ford owner who wants to stick with original equipment.

Champion

    According to Drew Shippy, a spokesperson from Champion, "The new Champion 7989, another one-piece design, has greater durability and is the hottest-selling spark plug Champion has." The Champion 7989 has a double platinum design, and withstands the carbon buildup characteristic of the 5.4 Triton engine. Its one-piece design addresses the problem of breakage during removal, and the superior heat-active alloy prevents excessive carbon buildup. The Champion is crimped and laser-welded to form one piece.

Autolite

    Autolite makes the HT-1.5, which was designed to be more durable than the HT-1. This single platinum spark plug was the Autolite answer to plugs breaking in the 5.4 Triton engines. According to Autolite, the original plug was redesigned for enhanced durability and power. Autolite designed the HT-1.5 to run hotter. Hotter-running plugs do not corrode and foul, and are self-cleaning. The spark plug continues to be a two-piece design, but incorporates a nickel plating to prevent corrosion and carbonization. The old Autolite plugs were designed with copper sheath and threads, which were prone to fusing and corroding.

Read More.. >

Thursday, October 10, 2013

How to Remove the Oxygen Sensor in a 2002 Jeep Grand 4 0L

In 1993, Jeep upped the ante in the SUV market by releasing the Grand Cherokee, a more luxurious mid-sized SUV. The 2002 Grand Cherokee came standard with a 195-horsepower, 4.0-liter in-line six-cylinder engine. Being an in-line-six engine, federal emission regulations require just two oxygen sensors, one upstream and one downstream. Replacing the two oxygen sensors in a federal emission-compliant 2002 Jeep Grand Cherokee is a straightforward process, but it may require additional heat for those hard-to-remove sensors.

Instructions

Upstream Sensor Removal Bank 1, Sensor 1

    1

    Park the Grand Cherokee on a flat surface and allow it to sit until the engine is completely cool. Allow the vehicle to sit for an additional hour to let the exhaust pipes cool.

    2

    Lift the front of the Grand Cherokee with a floor jack and slide jack stands under the frame rails. Lower the SUV onto the frame rails.

    3

    Crawl under the front of the Jeep until you have a good view of the bottom of the down pipe the pipe that bolts to the exhaust manifold. Find the upstream oxygen sensor screwed into the bottom of the exhaust manifold, near the front of the transmission.

    4

    Trace the sensors wiring until you reach where its harness connects to the Grand Cherokees harness. Unplug the oxygen sensors wiring harness from the Grand Cherokees wiring harness.

    5

    Unscrew the oxygen sensor from the exhaust down pipe, using a ratchet and oxygen sensor socket. If the sensor is seized, heat its base with a propane torch, then loosen it. Once the sensor cools, unscrew the sensor from the pipe.

Upstream Sensor Installation Bank 1, Sensor 1

    6

    Thread the new oxygen sensor into the down pipe by hand, then tighten it to 22 foot-pounds with a torque wrench and socket.

    7

    Connect the oxygen sensors wiring harness to the Grand Cherokees harness.

    8

    Raise the SUV off the jack stands and remove the stands. Lower the vehicle to the ground.

Downstream Sensor Removal Bank 1, Sensor 2

    9

    Lift the front of the Grand Cherokee off the ground with a floor jack and position jack stands under its frame rails. Lower the vehicle onto the jack stands.

    10

    Position yourself under the vehicle, just behind the transmission and toward the passengers side. Find the catalytic converter, the muffler-like component attached to the exhaust pipe. Find the downstream oxygen sensor, which screws into the exhaust pipe right after the catalytic converter.

    11

    Trace the downstream oxygen sensors wiring upward until you find where it connects to the Grand Cherokees wiring harness. Unplug the oxygen sensors wiring harness from the Grand Cherokees harness.

    12

    Remove the oxygen sensor by unscrewing it from the exhaust pipe, using a ratchet and oxygen sensor socket. If the sensor is seized, heat its base with a propane torch, then loosen it. Allow the sensor to sit until it is cool, then continue removing it.

Downstream Sensor Installation Bank 1, Sensor 2

    13

    Thread the new oxygen sensor into the exhaust pipe by hand, then tighten it to 22 foot-pounds with a torque wrench and oxygen sensor socket.

    14

    Connect the oxygen sensors wiring harness to the Grand Cherokees wiring harness.

    15

    Lift the SUV off of the jack stands and remove the stands. Lower the vehicle to the ground.

Read More.. >

Tuesday, September 17, 2013

How to Install a 98 Ford F150 4 6 Head Gasket

The Ford F150 is a 1/2-ton pickup truck that has been in continuous production since 1975. The 1998 model belongs the tenth generation of this series, which includes F150s made from 1997 to 2004. A 4.6-liter V-8 engine is one of the options available for the Ford F150. Each side of the engine has a cylinder head that covers the four cylinders on that side. The cylinder head gasket lies between the engine block and the cylinder head.

Instructions

    1

    Discharge the air conditioning system with a refrigerant recovery machine, if your vehicle is equipped with AC. This step requires a mechanic certified by the Environmental Protection Agency.

    2

    Remove the cable from the negative battery terminal with a socket wrench. Disconnect the valve covers, and remove the intake manifold from the engine block. Detach the timing chains from the crankshaft sprocket and camshaft sprocket. Disconnect both exhaust manifolds from the engine block. Disconnect the air compressor to obtain access to the cylinder heads if your vehicle has air conditioning.

    3

    Disconnect the retaining bolts from the heater hose with a socket wrench. Squeeze the hose clamp and pull it down the hose to release the clamp. Detach the heater hose from the cylinder head. Disconnect the mounting bolts from the cylinder head and pull the cylinder head from the engine block. Discard the gasket for the cylinder head and remove any remaining gasket material from the engine block with a gasket scraper.

    4

    Turn the crankshaft clockwise until the key way on the crankshaft points straight up, and clean the cylinder head with a shop rag. Place the the new gasket for the cylinder head gasket over the dowel pins on the engine block, then mount the cylinder head on the engine block.

    5

    Fasten new mounting bolts to the cylinder head by hand. Tighten the mounting bolts to between 27 and 31 foot-pounds on the first pass with a torque wrench. Tighten the bolts another 85 to 95 degrees with a socket wrench on the second pass. Tighten the bolts another 85 to 95 degrees on the third pass.

    6

    Connect the heater hose to the cylinder head, and attach the hose clamp. Fasten the retaining bolts for the heater hose with a socket wrench. Connect the exhaust manifolds to the engine block, and mount the timing chain to the crankshaft sprocket and camshaft sprocket. Connect the intake manifold, and replace the valve covers.

    7

    Attach the cable for the negative battery terminal with a socket wrench. Start the engine and check for coolant leaks. Recharge the air conditioning system, if your vehicle is so equipped. This requires a mechanic certified by the EPA.

Read More.. >