Showing posts with label plugs. Show all posts
Showing posts with label plugs. Show all posts

Sunday, March 30, 2014

How to Remove the Spark Plugs on a 2002 Chevy Malibu

The spark plugs on your 2002 Chevy Malibus 3.1-liter engine thread into the cylinder heads just below the valve covers. There are three spark plugs on each cylinder head. If you are replacing the spark plugs, be sure to only remove one at a time and replace it with a new one before moving to the next plug.

Instructions

    1

    Open the hood of your Malibu and locate the negative battery cable on the battery terminal. Loosen the clamp bolt on the cable end with a wrench, then remove the cable from the battery. Set it aside.

    2

    Locate the spark plugs on the right and left side of the engine. Select one of the spark plug wires and grasp the boot at the spark plug. Twist it slightly and pull it off the spark plug. Lay the wire aside.

    3

    Install a spark plug socket over the spark plug, attach a ratchet to the socket, then rotate the socket and plug counterclockwise. Lift the socket and spark plug out of the cylinder head. Repeat the process for all six spark plugs.

Read More.. >

Friday, March 14, 2014

How to Repair Sprinter Glow Plugs

How to Repair Sprinter Glow Plugs

A Mercedes Benz Sprinter glow plug repair is a tricky endeavor but a necessary one particularly for owners in cold climates who want quick startups. The glow plugs are the diesel engines equivalent to spark plugs and an ignition system. Without properly working plugs, the Sprinter may not start. When one glow plug goes bad, odds are the rest of the plugs are going bad too. Save yourself some time and trouble by replacing all the plugs at the same time.

Instructions

    1

    Disconnect the battery as a safety precaution.

    2

    Remove the injector lines, the injectors and the injector pump. Below the injectors are the heat shields that will need replaced. Remove the heat shields.

    3

    Disconnect the buss bar. Beneath the buss bar, you will have access to the glow plugs. Use a socket or a box-end wrench to remove the glow plugs. Use the magnetic tool to pick up the plugs as the fit is tight and you may not be able to get your hands in to grab them.

    4

    Apply the Teflon paste on the new plugs and install them. The magnetic tool will help you get the plugs into place, then use wrenches to tighten. Make the plugs snug but not overly tight. If you use a torque wrench, aim at about 15 pounds of torque.

    5

    Replace the buss bar, then install the new heat shields. Replace the injector lines, injectors and injector pump. Use the anti-seize on the injectors to prevent future problems with disassembling. Tighten the injectors to about 55 pounds of torque.

    6

    Start the Sprinter and check for leaks. The engine may be hard to start the first time. Continue to crank the engine until it starts. Double-check for leaks.

Read More.. >

Tuesday, December 10, 2013

Resistor Vs Non Resistor Spark Plugs for an ATV

Resistor Vs. Non-Resistor Spark Plugs for an ATV

Resistor-type spark plugs perform a crucial function on ATVs. These spark plugs contain a 5-kilowatt ohm ceramic resistor core inside the spark plug shell. The resistor functions as a suppressor against electromagnetic interference, also know as radio frequency interference, when the ignition fires at high voltage. This electricity "noise" can disrupt vehicle radios, often in the form of a hissing, popping or crackling noise. There is a marked difference between resistor and non-resistor spark plugs regarding ATV ignition systems and performance.

Ignition and Voltage

    ATV engines typically use a coil or magneto to produce a high-voltage spark that travels through the spark plug wire and to the spark plug. When the primary winding inside the coil is turned off or on, depending upon the type, it sends a signal to the secondary winding to activate. The secondary winding steps up the voltage from 12 volts to anywhere from 30,000 to 50,000 volts. This high voltage is required to create an arc between the spark plug ground and positive electrode. The high voltage creates a stray radio frequency noise.

Resistor vs. Non-Resistor -- Communications

    The primary purpose of resistor spark plugs for an ATV is to allow them to soak up powerful radio wave frequency interference. Since the electromagnetic discharge of high voltage also has a radio frequency signal, it often interrupts and causes static in ATV radios, CB radios and GPS systems. The resistor plug acts as a voltage soak to suppress static, crackling and loss of communication signal. Without resistor plugs, particularly on an older model ATV, no suppression exists, and interference can be detected in communication devices at any engine rpm. The noise interference can take on an annoying whine, directly proportionate to the engine speed.

Resistor vs. Non-Resistor -- Ignition Backlash

    On many off-road vehicles, the secondary systems, including resistor spark plugs, are used to reduce the high electrical backlash caused by the coils primary winding. The backlash, or extra electrical feedback, causes a disruption in the ignition system, such as the CDI boxes and igniters that are part of the ignition control modules. ATV vehicles that do not have such secondary resistor systems can show poor performance, such as periodic missing, rough idle and high-speed ignition cutout. ATVs and motocross bikes use resistor spark plugs to protect the ignition control modules.

Resistor vs. Non-Resistor -- Backlash and RFI

    Radio frequency interference can cause disruptive signals to an ATVs sophisticated on-board computer, which links to the control modules. Secondary electrical systems close to the coil will cause backlash and high RFI, since their voltage signal is significantly stronger. Resistor spark plugs suppress RFI and electronic backlash, keeping communication systems clear and on-board computers from harm. Non-resistor spark plugs can cause radio, CB and GPS static interference, as well as disrupt the entire ignition system. Newer ATV models with computer management systems will sometimes not start or run poorly when fitted with non-resistor spark plugs, due to the sensitivity of the computer and module settings.

Older ATV models

    ATV models manufactured before 1979, and some models prior to 1990, do not have computer engine management systems or microprocessors. Therefore, they do not have ignition problems related to radio frequency interference. These older off-road vehicles benefit from resistor spark plugs only in a communications application if they have been modified or fitted to accept a radio, CB or GPS system.

Resistor/Non-Resistor Advantages and Disadvantages

    The advantages of a resistor spark plug are straightforward, in that it suppresses RFI, for communications and ignition systems. However, resistor material is often composed of carbon material, which deteriorates with age. The deterioration will cause a suppression failure, leading to radio frequency interference. This results in additional maintenance. Resistor spark plugs do absorb some of the coils maximum reserve output, and this reduction applies more to older vehicles in which the owner has installed non-resistor plugs in a system that never had or required them. Older ATV models that do not have computers or communication systems do not suffer any RFI-related problems.

Read More.. >

Sunday, November 17, 2013

How to Replace Spark Plugs on a 1999 Chevrolet Camaro

The spark plugs on the 1999 Chevrolet Camaro engine are designed to provide the spark to the combustion chamber. The spark causes the gas fumes inside of the chamber to ignite. This combustion process allows the piston to compress up and down which in return enables the engine to crank and run. The spark plugs are powered by the distributor. As the inside of the distributor is turning, it supplies the power to the plugs. Over time, the plugs will foul out or corrode. Once this happens, change the spark plugs as soon as possible for maximum engine performance.

Instructions

    1

    Pull the 1999 Chevrolet Camaro into a safe work area and set the parking brake. Open the hood and prop it in place.

    2

    Locate the row of spark plugs on both sides of the engine block. The six-cylinder engines will have three spark plugs on each side of the engine block and the eight-cylinder engines will have four spark plugs on both sides of the engine block.

    3

    Move to the driver side of the engine block and remove the first spark plug wire that is closest to the front of the vehicle. Twist and pull out on the spark plug wire at the same time. Only replace one plug at a time to prevent crossing the plug wires.

    4

    Slide a long extension and a deep-well socket over the spark plug. Position a ratchet onto the extension and turn the spark plug counter clockwise until the plug is loose. Remove the ratchet, extension and socket from the plug and finish unscrewing the plug with your hand. Pull then plug out of the spark plug hole.

    5

    Screw the new spark plug into the spark plug hole until it is completely hand tight. Position the ratchet, extension and socket over the new plug and tighten the plug another one-quarter of a turn to completely seat the spark plug to the plug hole. Push the plug wire back over the tip of the spark plug until it locks on to the plug. Gently pull out on the plug to ensure that it is secured to the plug.

    6

    Move to the other spark plugs and repeat the same process for replacing the spark plugs. Be sure to only replace one plug at a time and to make sure that the plug wires are securely attached to the spark plugs.

Read More.. >

Tuesday, October 22, 2013

The Best Spark Plugs for a Ford 5 4 Engine

The Best Spark Plugs for a Ford 5.4 Engine

Frustration surrounds the Ford 5.4 Triton Engine. First, Ford had problems, according to Consumer Affairs, when the 5.4-liter engine blew spark plugs out of the head. Then, models from 2004 to 2008 were affected by spark plugs that were hard to remove and broke off in the head, according to Ford Technical Service Bulletin (TSB) 8-7-6. This affects all Ford and Lincoln Mercury vehicles with the 5.4-liter engine. The best spark plugs to install for the 5.4-liter Triton engine resist carbon buildup, are durable and come in one-piece.

Motorcraft

    The new Motorcraft spark plug for the 5.4 Triton engine, the MC SP507 platinum plug, replaces the old plug, PZT14F. The SP507 is one piece and has a little more durability. The design prevents fouling at low engine speeds, and is self-cleaning at high engine speeds. The old PZT14F was designed in two pieces, and would have a tendency to break off in the head due to carbon buildup on the seat. The newer plug tends to be more durable in the torque stress. The lack of carbonization buildup with the newer model aids in removing used spark plugs. This spark plug was made for the Ford owner who wants to stick with original equipment.

Champion

    According to Drew Shippy, a spokesperson from Champion, "The new Champion 7989, another one-piece design, has greater durability and is the hottest-selling spark plug Champion has." The Champion 7989 has a double platinum design, and withstands the carbon buildup characteristic of the 5.4 Triton engine. Its one-piece design addresses the problem of breakage during removal, and the superior heat-active alloy prevents excessive carbon buildup. The Champion is crimped and laser-welded to form one piece.

Autolite

    Autolite makes the HT-1.5, which was designed to be more durable than the HT-1. This single platinum spark plug was the Autolite answer to plugs breaking in the 5.4 Triton engines. According to Autolite, the original plug was redesigned for enhanced durability and power. Autolite designed the HT-1.5 to run hotter. Hotter-running plugs do not corrode and foul, and are self-cleaning. The spark plug continues to be a two-piece design, but incorporates a nickel plating to prevent corrosion and carbonization. The old Autolite plugs were designed with copper sheath and threads, which were prone to fusing and corroding.

Read More.. >