Showing posts with label 1999. Show all posts
Showing posts with label 1999. Show all posts

Sunday, May 18, 2014

How to Remove the Lower Intake Manifold in a 1999 Ford 3 8

The standard engine in a 1999 Ford Mustang is a six-cylinder, 3.8-liter engine with fuel injection. The intake manifold on a car with fuel injection distributes the combustion mixture evenly to the cylinder head intakes, and is essential for optimizing the performance of the engine. The intake manifold in a 1999 Ford with a 3.8-liter engine has an upper and lower section, which you must remove separately.

Instructions

    1

    Place a clean, sealable container under the radiator drain and remove the drain plug with a socket wrench. Allow the coolant to drain into the container and seal the container for later use. Replace the drain plug.

    2

    Remove the filler cap on the fuel tank to relieve the pressure in the fuel tank. Connect fuel pressure gauge T80L-9974-B to the pressure relief valve on the fuel supply manifold. Place the tube of the fuel pressure gauge into a container approved for gasoline and open the valve on the pressure gauge. Drain the excess fuel into the container to relieve the pressure in the fuel system.

    3

    Disconnect the battery cable from the negative terminal with a socket wrench. Remove the intake air temperature sensor and the air intake tube. Detach the cables for the cruise control and accelerator. Disconnect the bracket for the accelerator.

    4

    Detach the electrical connectors for the exhaust gas recirculation and vacuum regulator solenoids, if your vehicle is so equipped. Disconnect the electrical wires to the spark plugs and the ignition coil. Disconnect any additional vacuum lines needed to access the lower intake manifold.

    5

    Disconnect the positive crankcase ventilation valve from the crankcase with a socket wrench. Detach the electrical connector for the throttle position sensor and idle air control valve. Remove the exhaust gas recirculation valve. Disconnect the bracket for the wiring harness of the engine control sensor and push it out of your way.

    6

    Remove the upper intake manifold with a socket wrench. Detach the fuel lines from the fuel supply manifold and disconnect the electrical connector for the engine coolant temperature sensor. Remove the fuel supply manifold and fuel injectors from the lower intake manifold as an assembly.

    7

    Disconnect the upper radiator hose and heater hose from the radiator. Remove the lower intake manifold from the engine with a socket wrench.

Read More.. >

Saturday, April 12, 2014

How to Fix the Service Engine Soon Light in a 1999 Taurus

You can fix the Service Engine Soon light on your 1999 Taurus yourself at home using an OBD scan tool. OBD stands for On-Board Diagnostics system. This is the computer that stores the trouble codes sent to it by sensors positioned throughout the vehicle. Its job is to indicate what is going on in your vehicle and when it needs routine servicing. When you see the Service Engine Soon light flash on your instrument panel, you should have your Taurus serviced before you attempt to reset the system and turn off the light.

Instructions

    1

    Find the open port that is next to the fuse panel on the drivers side of the dashboard.

    2

    Plug the OBD scan tool into the open port.

    3

    Put the key into the ignition and turn the car on. Do not start the engine.

    4

    Look for the "erase" button on the scan tool and press it. Look on the instrument panel for the Service Engine Soon light to go out. Once it does, remove the scan tool from the port and turn off the car.

Read More.. >

Wednesday, April 9, 2014

How to Repair a Heater Motor Resistor on a 1999 BMW Z3 2 5L

The heater motor resistor on a 1999 BMW Z3 2.5-liter roadster is integrated into heater motor itself. This resistor plugs into the front side of the motor assembly. The heater resistor is not repairable; it must be removed and replaced if it fails. This resistor allows the motor to spin at variable speeds, consequently allowing the ventilation system inside the roadster to blow hot or cold air at different speeds. A bad motor resistor will either allow too much or too little current in to the motor, severely limiting the variable fan speed function of the HVAC system.

Instructions

Removal

    1

    Pry off both wiper arm caps with a small flat-head screwdriver, then remove the wiper arm bolts with a ratchet and socket. Mark the position of the wiper arms in relation to the spindles with a small tube of white paint. Lift the wiper arm up so they are at a 90-degree angle to the windshield, then lift the arms off of the wiper spindle gears.

    2

    Disconnect the washer pump tubing from the air intake/heating grille. Open the hood, then pry out the plastic retaining clips on both ends of the air intake/heating grille with the flat-head screwdriver. Lift the air intake/heating grille up and away from the lower windshield area, detach the remaining washer pump hoses, and remove the grille completely.

    3

    Disconnect the wiper motors electrical harness connector. Remove the bolts holding the wiper motor and arm assembly to the inside cowl, using a ratchet and socket, then slide the entire assembly to the left in order to disengage it from the integrated hooks. Lift the assembly out of the vehicle and set it on the ground or on a workbench.

    4

    Disengage the clamps on the blower motor fan cover by pushing them to the left until the pop loose, then set the cover aside.

    5

    Locate the heater motor resistor, directly below the motor body in the center of the assembly. Pry the resistor out of the fan assembly with a flat-head screwdriver. Discard the old resistor.

    6

    Press the new resistor into the fan motor assembly until its fully-seated.

    7

    Reinstall the heater motor cover and re-fasten the covers retaining clamps.

    8

    Position the wiper motor and wiper arm assembly inside the cowl section and slide it to the right to engage the locking tabs. Reinstall the retaining bolts for the wiper motor and wiper arm assembly.

    9

    Connect the washer pump hose to the underside of the air intake/heating grille assembly. Position the assembly over the cowl area and connect the top washer pump hose to the air intake/heating assembly.

    10

    Reinstall the plastic retaining pins on the corners of the air intake/heating grille assembly and press them down until they are fully-seated. Reinstall the wiper arms into their original position and then reinstall the wiper arm retaining bolts. Reinstall the wiper arm caps and test both systems to ensure proper operation.

Read More.. >

Monday, April 7, 2014

How to Replace the Ignition on a 1999 Pontiac Grand Prix

The 1999 Pontiac Grand Prix (available as a two-door coupe or a four-door sedan) typically has a six-cylinder 3.8-liter engine. The purpose of the ignition module is to control the electrical current to the spark plugs. The ignition module in the 1999 Pontiac Grand Prix is on top of the engine. The procedure for replacing the ignition module is similar for all Pontiac Grand Prix models with a 3.8-liter engine made from 1997 to 2000.

Instructions

    1

    Disconnect the cable for the negative battery terminal with a socket wrench. This will reduce the risk of electrocution while replacing the ignition assembly.

    2

    Label the wires to the spark plugs with tape to facilitate the installation of the new ignition module. You must reconnect the spark plug wires to their correct locations on the ignition assembly. Disconnect the spark plug wires from the ignition coils.

    3

    Remove the mounting screws for the ignition coils with a socket wrench and disconnect the ignition coils from the ignition module. Remove the fasteners for the ignition module and disconnect it from the engine.

    4

    Install the ignition coils to the new ignition module and fasten the retaining screws for the ignition coil. Torque the retaining screws to 40 inch-lbs. with a torque wrench.

    5

    Connect the spark plug wires to the ignition coils according to the labels you made in step 2. Attach the cable to the negative battery terminal with a socket wrench.

Read More.. >

Tuesday, February 11, 2014

The Removal of a Belt Driven Fan on a 1999 Dodge Dakota

Removing the mechanical fan from the front of the engine in your Dodge Dakota requires a specific wrench. The spanner wrench is available from tool dealers and through the Dodge dealerships parts department, though it can be expensive. Many auto parts stores rent these wrenches as well as stocking a new fan assembly for your Dakota. The fan assembly threads onto the water pump hub, and does not require removal of the drive belt to remove.

Instructions

    1

    Open the hood and locate the negative battery cable. Follow it to the battery and remove the retaining bolt securing the cable end to the battery terminal with a wrench. Lift the cable off the battery and set it aside.

    2

    Locate the bolts on the top section of the radiator shroud that secure the upper and lower halves. Remove the bolts with a socket and ratchet, then lift the top section of the shroud off the bottom section and remove it from the engine compartment.

    3

    Place a spanner wrench with a pin adapter on it between the fan and water pump hub. There are four holes in the face of the water pump hub. Slide the two pins on the spanner into two of these holes.

    4

    Grasp the fan blade with the opposite hand and spin the blades clockwise while holding the water pump hub with the spanner. The threads are right-handed, so turning it clockwise will loosen the blades.

    5

    Caully lift the fan assembly out of the engine compartment and store it in an upright position so the silicone gel inside does not leak out. Remove the spanner from the engine compartment.

Read More.. >

Monday, December 16, 2013

How to Replace a Starter on a 1999 Saturn

How to Replace a Starter on a 1999 Saturn

The starter in a 1998 Saturn mounts to the engine in the same location as most late model vehicles. It mounts below the engine, into the bell housing. In traditional fashion, the starter solenoid is bolted onto the starter to make it easier to remove both components at one time. When the starter fails to engage the flywheel, located inside of the bell housing, the engine does not start. When this happens, replace the starter to make your Saturn operable again.

Instructions

    1

    Disconnect the large black starter wire that connects to the starter. The wire secures to a threaded post on the starter with a small nut. The nut often rusts and removal is easiest with an adjustable wrench or vice grips.

    2

    Pull the wiring harness out of the Saturns starter solenoid by pushing on the small tab in the center and then by pulling on it.

    3

    Remove the three bolts that secure the starter to the Saturn. This requires a combination of a 12mm socket and a 12mm wrench. Use the socket on the two lower bolts and the wrench on the upper bolt. The use of a wrench accounts for clearance issues on the top bolt.

    4

    Pull the starter off the bell housing. Subsequently, this pulls the starter gear out of the bell housing where it meshes with the flywheel.

    5

    Place the new starter against the bell housing while you slide the gear into the bell housing. This meshes the gear with the flywheel.

    6

    Bolt the starter into place with the new bolts supplied with the starter. If new bolts were not supplied, use the old ones.

    7

    Slide the wiring harness onto the metal tab located on the starter solenoid until the harness snaps into place.

    8

    Reconnect the large black starter wire to the starter. Use the new nut threaded onto the replacement starter. Do not use the old nut.

Read More.. >

Sunday, November 17, 2013

How to Replace Spark Plugs on a 1999 Chevrolet Camaro

The spark plugs on the 1999 Chevrolet Camaro engine are designed to provide the spark to the combustion chamber. The spark causes the gas fumes inside of the chamber to ignite. This combustion process allows the piston to compress up and down which in return enables the engine to crank and run. The spark plugs are powered by the distributor. As the inside of the distributor is turning, it supplies the power to the plugs. Over time, the plugs will foul out or corrode. Once this happens, change the spark plugs as soon as possible for maximum engine performance.

Instructions

    1

    Pull the 1999 Chevrolet Camaro into a safe work area and set the parking brake. Open the hood and prop it in place.

    2

    Locate the row of spark plugs on both sides of the engine block. The six-cylinder engines will have three spark plugs on each side of the engine block and the eight-cylinder engines will have four spark plugs on both sides of the engine block.

    3

    Move to the driver side of the engine block and remove the first spark plug wire that is closest to the front of the vehicle. Twist and pull out on the spark plug wire at the same time. Only replace one plug at a time to prevent crossing the plug wires.

    4

    Slide a long extension and a deep-well socket over the spark plug. Position a ratchet onto the extension and turn the spark plug counter clockwise until the plug is loose. Remove the ratchet, extension and socket from the plug and finish unscrewing the plug with your hand. Pull then plug out of the spark plug hole.

    5

    Screw the new spark plug into the spark plug hole until it is completely hand tight. Position the ratchet, extension and socket over the new plug and tighten the plug another one-quarter of a turn to completely seat the spark plug to the plug hole. Push the plug wire back over the tip of the spark plug until it locks on to the plug. Gently pull out on the plug to ensure that it is secured to the plug.

    6

    Move to the other spark plugs and repeat the same process for replacing the spark plugs. Be sure to only replace one plug at a time and to make sure that the plug wires are securely attached to the spark plugs.

Read More.. >

Thursday, September 26, 2013

1999 Plymouth Breeze Torque Specifications for a Rear Hub Bearing

The Plymouth Breeze was a mid-sized automobile produced from 1996 to 2000 and offered with either a 2.0L or 2.4L engine. The vehicle sold well and is still a common sight on the road. If your 1999 Breeze has developed a high-pitch squeal emanating from the rear wheels, you should suspect that a bearing is worn. Proper installation of a wheel bearing requires that you tighten the attaching bolts or lock-nut to the proper torque.

Bearing Overview

    The rear suspension of a 1999 Plymouth Breeze uses standard shock absorbers. The rear wheels use sealed type wheel bearings, which are not serviceable. They are designed to last the life of the vehicle, but this is rarely the case. Often the bearings can be damaged, allowing dirt and water to enter. This causes the bearing to wear rapidly, requiring you to eventually replace the bearing.

Rear Wheel Bearing Description

    The rear wheel bearings are a combined unit. The five bolts that protrude from the hub flange support the brake drum and wheel and are what the wheel lug nuts attach to. The hub and bearing assembly is attached to the rear knuckle spindle and held on with a single lock nut. If you remove this lock nut for any reason you must replace it with a new one.

Checking the Bearings

    Jack up and support the rear of your Plymouth Breeze. Remove the rear wheels and brake drums. Inspect the bearings for grease. Slowly rotate the hubs, feeling for roughness, resistance or lateral movement, any of which may indicate that you need to change the hub/bearing assembly.

Rear Bearing Removal

    To remove the rear bearings, first jack up and support the rear of your Plymouth. Remove the rear wheels and brake drums. Use a flat-head screwdriver to pry off each metal hub dust cap. Use a socket wrench to remove the hub lock nuts. Pull the hub/bearing assemblies straight out of the spindles. When reassembling the bearing and hub assemblies, tighten the new lock nuts to 185 foot-pounds. Torque the wheel lug nuts to 95 foot-pounds.

Read More.. >

Saturday, September 21, 2013

1999 Dodge Status Dashboard Problems It Is Not Starting

1999 Dodge Status Dashboard Problems: It Is Not Starting

The 1999 Dodge has a dashboard with status lights that indicate a problem. If you cant start your car and your dashboard isnt lighting up, the problem is probably the battery. The car battery sends electricity to your dashboard and to the engine to start. You can test your battery to see if you need a new one.

Instructions

    1

    Remove the key from the ignition and pop the hood to gain access to the battery.

    2

    Tighten the connections to the battery terminals with a pair of pliers or a pair of channel locks. Try to start the vehicle.

    3

    Look over the battery terminal cables. If you find any corrosion on the terminals, use a can of soda and a stiff wire brush to clean the terminals.

    4

    Use a voltmeter to test the batterys charge. Place the red and black testing leads from the voltmeter to the red and black terminals on the battery.

    5

    Look at the reading. If its less than 11 to 12 volts, the battery needs to be replaced.

    6

    Replace the battery with a new one. If the car still wont start, have the car towed to a service shop for a diagnostics test.

Read More.. >