Showing posts with label lower. Show all posts
Showing posts with label lower. Show all posts

Sunday, May 18, 2014

How to Remove the Lower Intake Manifold in a 1999 Ford 3 8

The standard engine in a 1999 Ford Mustang is a six-cylinder, 3.8-liter engine with fuel injection. The intake manifold on a car with fuel injection distributes the combustion mixture evenly to the cylinder head intakes, and is essential for optimizing the performance of the engine. The intake manifold in a 1999 Ford with a 3.8-liter engine has an upper and lower section, which you must remove separately.

Instructions

    1

    Place a clean, sealable container under the radiator drain and remove the drain plug with a socket wrench. Allow the coolant to drain into the container and seal the container for later use. Replace the drain plug.

    2

    Remove the filler cap on the fuel tank to relieve the pressure in the fuel tank. Connect fuel pressure gauge T80L-9974-B to the pressure relief valve on the fuel supply manifold. Place the tube of the fuel pressure gauge into a container approved for gasoline and open the valve on the pressure gauge. Drain the excess fuel into the container to relieve the pressure in the fuel system.

    3

    Disconnect the battery cable from the negative terminal with a socket wrench. Remove the intake air temperature sensor and the air intake tube. Detach the cables for the cruise control and accelerator. Disconnect the bracket for the accelerator.

    4

    Detach the electrical connectors for the exhaust gas recirculation and vacuum regulator solenoids, if your vehicle is so equipped. Disconnect the electrical wires to the spark plugs and the ignition coil. Disconnect any additional vacuum lines needed to access the lower intake manifold.

    5

    Disconnect the positive crankcase ventilation valve from the crankcase with a socket wrench. Detach the electrical connector for the throttle position sensor and idle air control valve. Remove the exhaust gas recirculation valve. Disconnect the bracket for the wiring harness of the engine control sensor and push it out of your way.

    6

    Remove the upper intake manifold with a socket wrench. Detach the fuel lines from the fuel supply manifold and disconnect the electrical connector for the engine coolant temperature sensor. Remove the fuel supply manifold and fuel injectors from the lower intake manifold as an assembly.

    7

    Disconnect the upper radiator hose and heater hose from the radiator. Remove the lower intake manifold from the engine with a socket wrench.

Read More.. >

Thursday, October 3, 2013

How do I Lower 1995 Harley 883 Sportster

You can lower your 1995 Harley 883 Sportster on either the front or the back end. Lowering the front requires you to disassemble your forks and install shorter fork springs. Most Sportster riders do not shorten the fork springs for various reasons, including compromised handling. Lowering the rear end of your motorcycle is a simple job that wont affect the safety of the bike. You can get that slammed-in-the-weeds look for your Sportster by replacing your stock, 13-1/2-inch shocks with shorter ones.

Instructions

    1

    Remove your right and left saddlebags. If you have throw-over saddlebags, remove the seat by unscrewing the Allen bolt that secures your seat to the rear fender. You will probably not have to remove your saddlebag supports. If you have bolt-on saddlebags, immobilize the nut inside your fender with a box wrench, then loosen the nut on the outside of the fender with a socket wrench.

    2

    Raise the bike on a motorcycle jack until the rear wheel is completely off the ground. Make sure your motorcycle is stable.

    3

    Remove the lower shock mounting bolt and the washer nut on one side of your Sportster. Set them aside for reuse. Remove the upper bolt, washer and cover and set aside for reuse. Remove the shock absorber. Repeat on the other side.

    4

    Install the new shorter shocks, one side at a time. Put thread locker on the lower shock mounting bolt and reinstall. Reinstall the upper shock mounting bolt, using thread locker. Repeat for the opposite side.

    5

    Lower the bike carefully and support on the jiffy stand. Reinstall the saddlebags and the seat.

Read More.. >

Monday, September 30, 2013

How to Lower Engine Noise

Engines make noise. There is a level when the noise is just not comfortable and can make a trip very uncomfortable and unpleasant. Rule out any problems such as low oil pressure, any loose belts or a misfiring sparkplug and then you can set about toning down your noisy engine. Using easy-to-obtain materials and needing no prior auto repair experience you can tone down the noise form your engine and make everyone happier to ride in your car.

Instructions

    1

    Park the car on level ground and lift the hood. If the car is not level, the fluids inside will not be level.

    2

    Open the engine fluid reservoir and use the dipstick to check the level. If there is not enough fluid, fill the reservoir to the fill mark. Leave the hood open when you close the reservoir.

    3

    Start your engine and look through the engine bay for any loose or moving parts. Tighten these components in order to reduce the excessive noise they are causing.

    4

    Hold the soundproofing material against the underside of the hood and trace the shape of the indentations with a marker. There are usually three or four indented areas under the hood.

    5

    Cut out the material with scissors and apply the glue to the areas under the hood. Spread the cut-out pieces out onto the glue and press them down into place.

    6

    Cover the engine bay side of the firewall with the soundproofing material in the same way you did for the hood. The firewall is the wall between the engine compartment and the interior of the door.

Read More.. >