Friday, June 6, 2014
How to Troubleshoot a 95 Ci 2005 Harley Davidson
Harley Davidsons original compensator on 95-cubic-inch and larger twin cams may have been inadequate for the added torque produced by the newer engine. Harley now factory installs more robust compensators. There are sometimes electronic problems with fuel injected Harleys that can be difficult to diagnose. The usual procedure for that is to retrieve and translate the trouble codes. Beyond that, troubleshooting a 95-cubic-inch twin cam is not very different from troubleshooting a flathead 45. The process always begins with throwing your leg over the bike and sitting down.
Instructions
- 1
Open the petcock and extend the choke. Turn the ignition key switch to "On," the handlebar run switch to "On" and start the motorcycle. If the starter does not operate, your battery is dead.
2Shake the motorcycle from side to side and listen for gas sloshing in the fuel tank. If you hear sloshing and the starter turns over, but the bike does not start, check the spark plugs, the plug wires and the coil.
3Inspect the spark plug wires for breaks, wear and corrosion from the coil to the plugs. Remove the front spark plug with a socket wrench and a spark plug socket and inspect the plug. If you see anything other than a perfectly intact plug with a light gray or tan coating on the electrodes, your spark plug must be replaced.
4Start the motorcycle and idle in neutral until the rocker box covers under your left hand are warm to the touch. Ride the motorcycle.
5Listen as you ride. If you hear knocks or pings and your spark plugs are in good shape then the gasoline in your fuel tank is bad. If you hear a typewriter chattering either your pushrods or your tappets are improperly adjusted. If you hear a squeal when you stopped your brakes are worn out.
6Change gears. If the bike shifts hard, the shifter rod on the lower left side of the motorcycle may be bent. If the transmission jumps out of gear, the shifter forks in the transmission are improperly adjusted.
7Brake to a stop. If the brakes do not hold, the brake fluid in your master cylinder is low.
Wednesday, May 14, 2014
How do I Install 2001 883 Harley Sportster Push Rods
Pushrods, on the exterior of the cylinders on the right side of the engine, are part of an old-fashioned connection between the cam shaft and the exhaust and intake valves on your 2001, 883 cubic centimeter, V-twin Harley engine. Pushrods are specific to 883 and 1200 Sportster engines and Big Twins, but their operation, installation and removal is identical in all 2001 Harley V-Twin engines. Adjustable pushrods can conveniently be adjusted without having to first partially disassemble the top end of the engine. The initial top end job needed to install replacement pushrods is not for novices as clearances are tight, and many tools and some skill are required.
Instructions
- 1
Close the petcock. Put the motorcycle in fifth gear.
2Loosen the fender tab screw with an Allen wrench. Remove the seat.
3Loosen the battery cable from the negative terminal with an open end wrench. Disconnect the cable.
4Raise the motorcycle on a motorcycle jack until the rear tire clears the ground. Ensure the bike is stable.
5Remove the front and rear spark plugs with a spark plug socket and a socket wrench.
6Rotate the engine by rotating the rear wheel. Rotate the engine until the front piston, as viewed through the spark plug hole, is at the top of its stroke and both front lifters are at their lowest point in the compression cycle.
7Remove the front rocker box cover by loosening the rocker cover bolts with a rocker cover wrench. Remove the metal D-ring. Remove the gasket and discard.
8Insert a small, flat head screwdriver blade into the cast loop of the spring cap retainer at the top of the rear pushrod cover for the front cylinder.
9Rotate the screwdriver bottom toward the outboard side while pushing down. Remove the spring cap cover. Repeat the procedure for the other front cylinder pushrod.
10Collapse the upper and lower push rod covers.
11Alternately loosen each of the four rocker arm support plate bolts in 1/4 turn increments until all four bolts are loose. Remove the rocker arm support plate assembly.
12Remove the push rod covers from the cylinder head and lifter cover bores. Remove the three O-rings from the push rod covers and discard.
13Remove the pushrods by hand.
14Assemble the new pushrod covers. Insert the pushrod cover adapters in the cover retainers.
15Insert the new pushrods in the cylinder head and lifter cover bores. Install the new cover O-rings included with the new pushrods.
16Replace the rocker arm support plate into the rocker housing. Loosely install the four rocker arm support plate bolts.
17Tighten the four rocker arm support plate bolts in a cross pattern by tightening each bolt 1/4 turn at a time. Final tighten the bolts to 18 to 22 foot pounds of torque with a torque wrench and a "dog bone" torque adapter.
18Install a new rocker box cover gasket. Replace the D-ring.
19Replace the rocker box cover. Tighten the rocker box cover bolts in a cross pattern to 20 foot pounds of torque with a torque wrench.
20Extend the adjusting screws to remove lash in the pushrods.
21Compress the hydraulic unit in the exhaust lifter four complete turns and tighten the lock nut.
22Adjust slack in the pushrod with your fingers after waiting five minutes. Repeat all procedures for the rear cylinder.
23Replace the spark plugs and tighten them with a spark plug socket and socket wrench.
24Lower and remove the motorcycle jack. Shift the motorcycle into neutral.
25Start the motorcycle and check for leaks.
Wednesday, March 26, 2014
How to Adjust a Rear Brake Pedal on a Harley Road Glide
The original equipment connection between the rear brake pedal and the rear brake master cylinder on all Harley-Davidson Road Glides to date is completely mechanical and not hydraulic. The mechanical connection is the same whether your Road Glide is equipped with your original brake pedal or an aftermarket pedal.
Instructions
- 1
Sit down next to the right side of your motorcycle and find the brake pedal.
2Find the rear brake master cylinder which is approximately parallel to the bottom of the brake pedal and about two feet closer to the rear of the bike. Then find the metal rod that connects the two.
3Loosen the jam nut that connects the rear brake cylinder to the brake rod by turning the nut counterclockwise with an open end wrench.
4Turn the brake rod with an open end wrench fitted to the flattened section of the brake rod. Turn the rod clockwise to lower the pedal and counterclockwise to raise the pedal.
5Tighten the jam nut by turning it clockwise when the brake pedal is adjusted to the proper height.
6Inspect the cotter pin that locks the brake rod to the brake pedal assembly. Use pliers to replace the cotter pin if it is broken or very corroded.
Tuesday, March 11, 2014
How to Install Vance Hines Exhaust on a Harley Davidson Rocker
The Rocker is Harley-Davidsons custom chopper. With its solo seat, fat rear tire and kicked-out front end, it looks like it has been stripped down for speed. It actually weighs about 700 lb., however, and the engine produces only about 63 horsepower. Vance & Hines is one of several aftermarket exhausts. The Vance & Hines exhaust should boost your Rockers horsepower above 70.
Instructions
- 1
Cover all finished areas on the right side of the motorcycle with rags to protect your paint and chrome. Remove the right foot peg and brake pedal with a socket wrench. Loosen all of the fasteners that connect your exhaust manifold and exhaust support bracket with a socket wrench or box wrenches. Disconnect the two oxygen sensors with a wrench. You will reinstall these sensors with your new exhaust.
2Loosen all remaining fasteners holding the exhaust on by hand. Remove the old exhaust. Remove and replace the exhaust manifold gaskets. Using a small screwdriver or snap ring pliers, remove and set aside the clamps and retainer rings. You will use them on your new exhaust.
3Install all of the hose clamps that will support the heat shields. They must remain loose. If you tighten the hose clamps at this point, you risk warping your exhaust.
4Use a wrench and thread locker to bolt on the new exhaust mounting bracket that came with your Vance & Hines pipes.
5Reinstall your retainer rings and clamps in your new exhaust. Loosely bolt your new exhaust to your exhaust manifold and exhaust support bracket. Put Teflon paste on the oxygen sensors and reinstall them in your new header pipes.
6Tighten the bolts that attach your new exhaust to the exhaust headers and support bracket using a wrench. Attach your heat shields to the hose clamps with a flat-head screwdriver.
Saturday, February 22, 2014
How to Remove Dust Covers From a Harley Fork
Harley-Davidson motorcycles come with dust covers on the fork of the front tire, which prevent dust and other unwanted materials from entering the fork. The stock dust cover is generally black rubber, but these are often replaced with fancier ones such as shiny aluminum. In order to replace the dust covers, or clean underneath them, the old ones need to be removed.
Instructions
- 1
Locate the small indent on the dust cover.
2Cover the indent with tape. This will help keep the dust cover from being scratched or dented.
3Insert the tip of a screwdriver into the indent and hold it in place.
4Hammer the end of the screwdriver gently. This will cause the dust cover to fall off.
Friday, January 31, 2014
Harley Auxiliary Lighting Instructions
The first thing you should know is that if you own a Softail manufactured after 2006, installing an auxiliary lighting kit will be a longer and more involved job than it may seem to you now, as you languidly lean against one wall of your garage, rub your chin and consider how next to improve your ride. Since the 2007 model year, all Harleys have come equipped with Electronic Fuel Injection so electronics are everywhere, including in your fuel tank. Further, Harley recommends that the fuel tank come off then go back on when you install the motor companys auxiliary lighting kit. Novice mechanics may confidently begin this job, but they will no longer be novices when they are done.
Instructions
Removing The EFI Fuel Tank
- 1
Ride your motorcycle until the fuel gauge registers less than 1/4 tank.
2Release the fuse box cover under the right side of the seat by pulling on it. Disconnect the fuel pump fuse by sliding flathead screwdriver behind one side of the fuse.
3Shift the bike into neutral and start the engine. After the engine dies continue to try to start the engine for several more seconds.
4Separate the fuel supply line from the tank by sliding the fitting sleeve up and the pulling the fuel hose down.
5Remove the Phillips screw from the rear fender seat tab with a Phillips head screw driver. Pull off the seat.
6Remove the black wire from the negative battery post with a combination wrench.
7Loosen the instrument panel by removing the chrome nut in the middle of the panel with an Allen wrench. Pull the two halves of the fuel pump module connector apart and remove the instrument panel.
8Stop one end of a 5/16 inch hose with a 5/16 inch bolt. Fasten the bolt in the hose with a worm style hose clamp and a flat head screwdriver.
9Set a large gas can near the bike. Cut the hose clamp on one end of the crossover line under the tank with tin snips.
10Remove the unclamped end of the crossover line from the tank fitting and replace it with the unclamped end of the 5/16 inch hose. Drain the remaining gasoline from the fuel tank into the large gas can through the open crossover line.
11Remove spilled gasoline from around the motorcycle with rags. Move the rags and gasoline outside and away from the bike.
12Unsnap the continuous vent line and crossover line from the fittings on the bottom of the tank and set aside.
13Remove the front and rear tank mounting bolts and their washers and nuts with an open end wrench. Pull apart the two halves of the wiring harness fuel gauge connector.
14Remove the fuel tank.
Install Auxiliary Lights
- 15
Mount the mounting clamps to the left and right fork tubes with the four Allen screws in the lighting kit. Tighten the screws to 70 inch pounds of torque with a torque wrench and an Allen socket.
16Push the wires from the two bar lights through the mounting bracket holes. Fasten the two lamps to the two brackets with the clamp blocks, retainers and washers in the lighting kit.
17Tighten the retainers to 20 pounds with an open end socket and torque wrench.
18Slide the inner nesting rings onto each auxiliary light bulb. Connect the black wires to the black quick connect terminals adjacent to the indexing tabs and the gray wires to the remaining quick connect terminals.
19Lock the bulbs into the outer trim rings with the screws in the kit and a Phillips head screwdriver. Pull the accessory lamp wires through the chrome conduits included in the kit.
20Set the accessory lighting wiring harness included with the kit in the seat pan. Stretch the longest wires to the steering head along the frame.
21Unscrew the nut on the grounding stud next to the seat pan with an open end wrench. Slip the metal ring on the black wire in the accessory lighting wiring harness over the stud. Refasten the hex nut with an open end wrench.
22Mate the white wiring connector to positive connector "B" on the accessory wiring included with the kit. Tie the accessory lighting wiring harness to the adjacent wires with the plastic ties included in the kit.
23Extend the longest wires in the accessory harness past the steering head. Route the switch wires across the left side of the handlebars to the clutch lever.
24Install the small chrome switch into the switch mounting bracket included in the kit using a Torx driver.
25Remove the bottom screw from the clutch lever cover with a Torx socket and socket wrench. Position the tab of the switch bracket over the screw hole and replace the bottom screw. Tighten the bottom screw to 65 inch pounds with a torque wrench and a Torx socket.
26Fasten the switch wire to the handlebar wire clips. Loosen and remove the chrome, headlight trim ring with a Phillips head screwdriver.
27Disconnect the female connector block from the headlight plugs. Pull the black, weather proof boot off the back of the headlamp.
28Squeeze the headlight retaining clip to remove it from the headlight assembly. Remove the headlight bulb by twisting the clip and pulling the bulb.
29Thread the light switch wire into the headlamp housing through the rubber grommet on the back of the housing. Connect the switch wire to the yellow, low beam wire using the double-ended tube connector in the kit and wire crimpers.
30Remount the headlamp in the headlamp housing.
31Insert the white wire in the auxiliary wiring harness into heat shrinkable tubing from the kit. Remove 3/8 inch of insulation from the ends of the two auxiliary light wires with a wire stripper.
32Join the three wires with the Y tube connector in the lighting kit and a crimping tool. Slide the heat shrinkable tubing over the splice and shrink with a heat gun.
Reassemble The Bike
- 33
Secure the loose auxiliary lighting wires to the lower fork with the clips included in the auxiliary lighting kit.
34Reconnect the fuel tank and all hoses. Connect the negative battery cable to the negative battery post.
35Reinsert the fuel pump fuse and close the electrical caddy cover.
36Reinstall the seat and uel the motorcycle.
Saturday, November 30, 2013
How to Time a Harley Davidson Motorcycle
Checking the timing on your Harley-Davidson motorcycle every 5,000 miles plays an important role in a comprehensive maintenance routine. As a Harley-Davidson engine ages, you must adjust the ignition timing to compensate for the wear of internal engine parts. Setting the timing correctly keeps your motorcycle running smoothly and efficiently. Maladjusted timing may result in sluggish performance, poor fuel economy and possible damage to internal engine components. Setting the timing is relatively easy and ensures the maximum life from the engine.
Instructions
- 1
Remove the crankcase timing plug using an Allen wrench, and expose the timing hole. The timing hole is located on the primary chain case side of the motor on the engine block and capped with a solid hex-head plug. Install a clear plastic timing hole plug to prevent oil splash.
2Connect the positive terminal of an inductive timing light to the positive battery terminal of the motorcycle. Connect the negative terminal of the timing light to the negative terminal of the battery. Connect the inductive pickup probe of the timing light to the front cylinder spark plug wire.
3Start the engine, and run it at idle. Point the timing light into the timing inspection hole. If the ignition is properly timed, the timing bar will align with the circular timing reference mark. The reference marks on a correctly timed engine will appear as a vertical bar through the center of the circle. Some models only have a timing reference mark on the flywheel of the motor; on these models, the engine is correctly timed when the reference mark is visible in the timing inspection hole.
4Remove the timing cover from the right side of the motor with a Phillips screwdriver or Allen wrench, depending on your specific model. Loosen the the timing plate screws with a slotted screwdriver, and turn the timing plate to adjust the timing. Recheck the timing marks with the timing light. Tighten the timing plate screws, and install the cover.
5Shut off the engine, and remove the timing light. Remove the clear plastic timing hole plug, and install the solid plug in the hole.
Friday, October 25, 2013
Harley Flywheel Balance Symptoms
Every motorcycle that comes off the Harley-Davidson assembly line is different. Each half of a flywheel, each crankshaft, piston, rod, ring, lock, button and cage making up the entire flywheel assembly is equally different from the others. Because of the sensitive nature of the function provided, a featherweight imbalance in the flywheel grows exponentially to affect the smooth ride of your bike -- especially the Harley Sportster and the 45 degree V-Twin, affectionately known as the "Shaker".
Engine Shakes
The flywheel assembly buffers and moderates power put out by an engine. The 45-degree angle of the Harley V-Twin engine makes it difficult to cancel out the reciprocating spins of the engine; if you feel as if your teeth will out of your head when you ride, you are experiencing the not difficult-to-detect Harley balance symptoms inherent in your hog. Because the parts are assembly made, the two halves of the flywheel will not be exact. Any slight difference in weight between the two halves creates an imbalance that, once it shakes through the entire assembly, intensifies the engines vibration.
Factory-Bought Harleys
Balancing the flywheel is an expensive and time-consuming operation. Each bike undergoes a balancing procedure to a manufacturing standard applied to each model and then released to the dealer. Factory-bought machines have advantages. When it comes to Harley troubleshooting, however, a customized bike is less likely to shake than a factory-issued bike. When you turn the ignition on and the engine starts to shake in an elliptical fashion or you find yourself wearing out ball bearings at a great rate, the flywheel assembly was likely only factory balanced.
Engine Shakes Above 3000 RPM
The higher the revolutions per minute (rpm), the greater the horsepower used and the greater the stress placed on the engine. Harley balance symptoms increase to the point of becoming unmistakable and discomfiting vibrations. If you drag race with your bike then, you are taking it above standard operational rpm. Even if you had your flywheels balanced for regular street riding, the greater demand you put on your Harley will cause a change in the rotation of the flywheels and accentuate any slight imbalance. You may also have customized the pistons or even the flywheels themselves for enhanced racing performance, which will also cause a misalignment of the flywheel assembly, resulting in the shakes.
Tuesday, October 8, 2013
How to Assemble a Harley Oil Tank Hose
There are only four possible oil hoses on any Harley-Davidson. One hose, usually called the "feeder line," carries oil from the oil tank to the oil pump. Another hose, usually called the "return line," carries oil from the engine to the oil tank. Harleys built after 1992 have a third line, usually called a "vent line," that connects the oil tank and crankcase. All Harleys have a way to drain the oil from the tank (sometimes it is a "drain line" and at other times a "drain-feed" line). All connections are straightforward and are made with either hose clamps or hex nuts.
Instructions
- 1
Drain oil from the oil tank through a drain hose by loosening a hose clamp at one end of the hose with a flat-head screwdriver. Turning the screw causes the clamp to expand or contract. Pull the drain plug from the end of the hose when the clamp is loose.
2Loosen the hose clamps that connect oil hoses to possible T-fittings and elbow fittings by loosening the hose clamps there with a flat-head screwdriver. The hose clamp tightens the flexible hose to ridged metal connections on the fitting. When the clamp is loose pull the hose free.
3Loosen the hose clamp connection between the oil tank and the feeder line with a screwdriver. Tighten the connection between the feeder line and the fixed, threaded, oil pump fitting with an open-end wrench.
4Push the oil vent and oil return lines through the rubber grommets in the holes near the top front of the oil tank.
5Connect the crankcase end of the oil vent line to the fixed, threaded, crankcase fitting with an open-end wrench. Connect the oil pump end of the return line to the fixed, threaded, oil pump fitting with an open-end wrench.
Thursday, October 3, 2013
How do I Lower 1995 Harley 883 Sportster
You can lower your 1995 Harley 883 Sportster on either the front or the back end. Lowering the front requires you to disassemble your forks and install shorter fork springs. Most Sportster riders do not shorten the fork springs for various reasons, including compromised handling. Lowering the rear end of your motorcycle is a simple job that wont affect the safety of the bike. You can get that slammed-in-the-weeds look for your Sportster by replacing your stock, 13-1/2-inch shocks with shorter ones.
Instructions
- 1
Remove your right and left saddlebags. If you have throw-over saddlebags, remove the seat by unscrewing the Allen bolt that secures your seat to the rear fender. You will probably not have to remove your saddlebag supports. If you have bolt-on saddlebags, immobilize the nut inside your fender with a box wrench, then loosen the nut on the outside of the fender with a socket wrench.
2Raise the bike on a motorcycle jack until the rear wheel is completely off the ground. Make sure your motorcycle is stable.
3Remove the lower shock mounting bolt and the washer nut on one side of your Sportster. Set them aside for reuse. Remove the upper bolt, washer and cover and set aside for reuse. Remove the shock absorber. Repeat on the other side.
4Install the new shorter shocks, one side at a time. Put thread locker on the lower shock mounting bolt and reinstall. Reinstall the upper shock mounting bolt, using thread locker. Repeat for the opposite side.
5Lower the bike carefully and support on the jiffy stand. Reinstall the saddlebags and the seat.
Sunday, September 22, 2013
How to Troubleshoot the Fuel System on a Harley Davidson
In a carbureted Harley, gasoline flows from the gas station, to the gas tank, by gravity through the petcock to the carburetor, then to the intake valves after which it explodes. In a fuel-injected Harley the gas is pumped from the fuel tank to the fuel injectors, which spray the gasoline into the intake valves. The most likely components to malfunction in a fuel-injected bike are the fuel pump or any of the multiple electronic sensors on such a bike. The fuel system on a fuel-injected Harley is diagnosed electronically. Troubleshooting the fuel system on a carbureted Harley is less susceptible to electronic gremlins and may be more illustrative of what makes these vehicles go.
Instructions
- 1
Open the gas cap and smell the gasoline. Shine a flashlight into the tank. If you see water or diesel oil floating on top of the gasoline, you must drain the fuel from the carbureted Harley.
2Disconnect the hose clamp that secures the fuel line to the petcock with a flat-head screwdriver. Replace the fuel line at the petcock with a 2-foot length of 1/4-inch rubber hose.
3Insert the open end of the hose in an empty, 5-gallon gas can. Open the petcock to "reserve" and drain the fuel.
4Unscrew the petcock from the bottom of the fuel tank with an open-end wrench. Examine and, if necessary, clean the fuel filter.
5Reinstall the petcock with an open-end wrench. Replace the fuel line on the petcock using a screwdriver and put 1 gallon of fresh gasoline in the fuel tank.
6Open the petcock, open the choke, put the bike in neutral and attempt to start the motorcycle.
7Open the throttle if the bike starts and fully close the choke. Run the motorcycle until the rocker box covers are warm to the touch and allow the throttle to return to normal idle. If the engine dies at a normal idling speed take the following steps.
8Restart the motorcycle and idle the bike with the choke pulled halfway out. If the bike runs with the choke half out, but not pushed fully in, the fuel-air mixture in the carburetor has too much air and not enough gasoline.