Wednesday, November 6, 2013
How to Replace the Exhaust System on a Nissan Pathfinder
Replacing the exhaust system as a whole or in pieces requires some inspection of the components to determine what is damaged or worn out. The exhaust system is responsible for removing spent gases and fumes from the engine and out the back of the vehicle. If it has holes or leaks, it can become dangerous to the passengers inside the vehicle. You can purchase the parts of the system in sections or buy the whole system at most auto parts stores.
Instructions
- 1
Raise your Pathfinder off the ground with a jack. Support it with jack stands under all four corners of the truck. Make sure the truck is high enough that you can work under it comfortably while still being stable.
2Remove the clamp holding the tailpipe to the rear of the muffler by loosening the nuts on the clamp with a wrench and separate the two pipes. Remove the tail pipe from the hanger at the rear of the truck by pulling the pin on the pipe out of the rubber hanger on the truck and working the pipe loose from the muffler. Move the pipe out from under the truck.
3Locate and remove the bolts that secure the muffler to the front right and left exhaust pipes. These are the pipes that come down from the exhaust manifolds.There is a flange on each pipe with a gasket and two bolts that hold the muffler to these pipe sections.
4Remove the two hangers that hold the muffler up by removing the bolts from them using a ratchet and socket. There are two on each hanger. Drop the muffler down to the ground and remove it from under the truck.
5Remove the nuts from the manifold studs where the front pipes attach. There are two nuts on each pipe and a bronze O-ring that seals the pipe to the manifold. Remove the pipes and O-rings and discard them.
6Install a new right and left front pipe after installing the new bronze O-ring in the pipe. Slide the pipe onto the manifold studs then install the nuts. Tighten the nuts with a socket and ratchet until they are secure and do not move around.
7Install the new muffler to the front pipes and install a new gasket in between the two flanges. Insert the mounting bolts and tighten them with a wrench or socket and ratchet. Reinstall the hangers and tighten the bolts with a socket and ratchet or wrench.
8Install the new tailpipe by sliding the tailpipe onto the pipe exiting the rear of the muffler and slide the hanger pin into the rubber hanger at the rear of the truck. Install a new exhaust clamp on the joint between the muffler and tail pipe and tighten the nuts with a wrench or socket and ratchet.
9Remove the jack stands from under the truck and use a jack to carefully lower the truck down to the ground.
Wednesday, October 23, 2013
How to Choose an Exhaust System for Sound
You want to choose your exhaust so the other cars on the road know youre there. But its important to know which exhaust systems give you the best performance as well as sound. Heres how to choose one of the best exhaust systems for your ride while keeping muffler tone a priority.
Instructions
- 1
Preview the sound before you put out the cash. Dynomax performance exhaust systems have sound bytes that you can download for some of their systems on Firebirds, Mustangs and Civics with a Vtec engine. Log on to the A-1 Performance website to get an earful.
2Cruise the local shows for ideas. Nothing compares to hearing an exhaust system in person, so scope out the sights and most importantly, the sounds, at the local car cruise. Youll get ideas of what works best on your make and model.
3Choose your sound. Decide if you want the classic V-8 rumble or a more toned-down sound. A great choice in either case is one of the Flowmaster exhaust systems. You can trust their 22 years of experience in the muffler business and they have an exhaust for every type of sound youre looking for.
4Decide whether you want a dual exhaust or single exhaust system. Keep in mind that some dual exhaust systems dont perform properly because they are designed only for looks. To ensure a great dual exhaust sound, be sure to choose a system like the Flowmaster.
5Keep performance a priority. The exhaust systems note is important, but dont sacrifice performance for sound. Be sure your exhaust system matches your engine manifold and is fitted correctly down your undercarriage, or else you may be looking at decreased engine performance.
Monday, October 21, 2013
How to Install a Flowmaster Exhaust System
For as long as there have been muscle cars, there has been a desire by some owners to make their cars louder and more powerful. One modification that accomplishes both of these tasks is to install a Flowmaster exhaust system on your vehicle. The reduced exhaust backpressure associated with this installation will raise your engines horsepower slightly, as well as give your machine a classic muscle car sound. The Flowmaster exhaust system can be installed on your vehicle in just a few hours with regular mechanics tools.
Instructions
- 1
Back your vehicle onto a set of car ramps and apply the parking brake. Chock the front wheels to prevent any unwanted movement.
2Crawl under the vehicle and apply penetrating fluid to the fittings on your present exhaust system to allow for easier removal. Allow the fluid to work in for several minutes be continuing.
3Don safety goggles and gloves for protection against falling rust particles and sharp metal edges. Loosen the pipe clamps on the exhaust system by turning the clamp nuts in a counterclockwise direction with an adjustable wrench.
4Remove the bolts from the exhaust hangers at the rear of the car with an adjustable wrench turned in a counterclockwise direction. Work the exhaust system towards the back of the car to separate it from the exhaust head pipes. Use a twisting motion on the exhaust pipes to separate them from the head pipes if necessary. Lower the exhaust system from the vehicle. Remove the rubber isolators and pipe hangers from the mufflers with an adjustable wrench turned in a counterclockwise direction. Save these parts for the installation of the Flowmaster system. Discard the old exhaust system..
5Install the rubber isolators and hangers to the new Flowmaster exhaust system with the original bolts turned with an adjustable wrench in a clockwise direction. Note that the hangers will install to your Flowmaster system in the same fashion as your stock exhaust.
6Place the Flowmaster system under your vehicle with the mufflers facing the rear. Raise the system up and fit the front of the Flowmaster pipes into the vehicles head pipes until they are fully seated. Attach the pipe hangers to the bottom of the car using the original mounting holes and bolts tightened with an adjustable wrench in a clockwise direction. Install the pipe clamps supplied with your Flowmaster kit onto the joint where the pipes meet the cars original head pipes. Tighten the clamps with an adjustable wrench in a clockwise direction.
7Remove the wheel chocks, release the parking brake, and carefully drive the car off of the ramps.
Sunday, September 22, 2013
How to Troubleshoot the Fuel System on a Harley Davidson
In a carbureted Harley, gasoline flows from the gas station, to the gas tank, by gravity through the petcock to the carburetor, then to the intake valves after which it explodes. In a fuel-injected Harley the gas is pumped from the fuel tank to the fuel injectors, which spray the gasoline into the intake valves. The most likely components to malfunction in a fuel-injected bike are the fuel pump or any of the multiple electronic sensors on such a bike. The fuel system on a fuel-injected Harley is diagnosed electronically. Troubleshooting the fuel system on a carbureted Harley is less susceptible to electronic gremlins and may be more illustrative of what makes these vehicles go.
Instructions
- 1
Open the gas cap and smell the gasoline. Shine a flashlight into the tank. If you see water or diesel oil floating on top of the gasoline, you must drain the fuel from the carbureted Harley.
2Disconnect the hose clamp that secures the fuel line to the petcock with a flat-head screwdriver. Replace the fuel line at the petcock with a 2-foot length of 1/4-inch rubber hose.
3Insert the open end of the hose in an empty, 5-gallon gas can. Open the petcock to "reserve" and drain the fuel.
4Unscrew the petcock from the bottom of the fuel tank with an open-end wrench. Examine and, if necessary, clean the fuel filter.
5Reinstall the petcock with an open-end wrench. Replace the fuel line on the petcock using a screwdriver and put 1 gallon of fresh gasoline in the fuel tank.
6Open the petcock, open the choke, put the bike in neutral and attempt to start the motorcycle.
7Open the throttle if the bike starts and fully close the choke. Run the motorcycle until the rocker box covers are warm to the touch and allow the throttle to return to normal idle. If the engine dies at a normal idling speed take the following steps.
8Restart the motorcycle and idle the bike with the choke pulled halfway out. If the bike runs with the choke half out, but not pushed fully in, the fuel-air mixture in the carburetor has too much air and not enough gasoline.