Showing posts with label davidson. Show all posts
Showing posts with label davidson. Show all posts

Friday, June 6, 2014

How to Troubleshoot a 95 Ci 2005 Harley Davidson

How to Troubleshoot a 95 Ci 2005 Harley Davidson

Harley Davidsons original compensator on 95-cubic-inch and larger twin cams may have been inadequate for the added torque produced by the newer engine. Harley now factory installs more robust compensators. There are sometimes electronic problems with fuel injected Harleys that can be difficult to diagnose. The usual procedure for that is to retrieve and translate the trouble codes. Beyond that, troubleshooting a 95-cubic-inch twin cam is not very different from troubleshooting a flathead 45. The process always begins with throwing your leg over the bike and sitting down.

Instructions

    1

    Open the petcock and extend the choke. Turn the ignition key switch to "On," the handlebar run switch to "On" and start the motorcycle. If the starter does not operate, your battery is dead.

    2

    Shake the motorcycle from side to side and listen for gas sloshing in the fuel tank. If you hear sloshing and the starter turns over, but the bike does not start, check the spark plugs, the plug wires and the coil.

    3

    Inspect the spark plug wires for breaks, wear and corrosion from the coil to the plugs. Remove the front spark plug with a socket wrench and a spark plug socket and inspect the plug. If you see anything other than a perfectly intact plug with a light gray or tan coating on the electrodes, your spark plug must be replaced.

    4

    Start the motorcycle and idle in neutral until the rocker box covers under your left hand are warm to the touch. Ride the motorcycle.

    5

    Listen as you ride. If you hear knocks or pings and your spark plugs are in good shape then the gasoline in your fuel tank is bad. If you hear a typewriter chattering either your pushrods or your tappets are improperly adjusted. If you hear a squeal when you stopped your brakes are worn out.

    6

    Change gears. If the bike shifts hard, the shifter rod on the lower left side of the motorcycle may be bent. If the transmission jumps out of gear, the shifter forks in the transmission are improperly adjusted.

    7

    Brake to a stop. If the brakes do not hold, the brake fluid in your master cylinder is low.

Read More.. >

Tuesday, March 11, 2014

How to Install Vance Hines Exhaust on a Harley Davidson Rocker

How to Install Vance & Hines Exhaust on a Harley Davidson Rocker

The Rocker is Harley-Davidsons custom chopper. With its solo seat, fat rear tire and kicked-out front end, it looks like it has been stripped down for speed. It actually weighs about 700 lb., however, and the engine produces only about 63 horsepower. Vance & Hines is one of several aftermarket exhausts. The Vance & Hines exhaust should boost your Rockers horsepower above 70.

Instructions

    1

    Cover all finished areas on the right side of the motorcycle with rags to protect your paint and chrome. Remove the right foot peg and brake pedal with a socket wrench. Loosen all of the fasteners that connect your exhaust manifold and exhaust support bracket with a socket wrench or box wrenches. Disconnect the two oxygen sensors with a wrench. You will reinstall these sensors with your new exhaust.

    2

    Loosen all remaining fasteners holding the exhaust on by hand. Remove the old exhaust. Remove and replace the exhaust manifold gaskets. Using a small screwdriver or snap ring pliers, remove and set aside the clamps and retainer rings. You will use them on your new exhaust.

    3

    Install all of the hose clamps that will support the heat shields. They must remain loose. If you tighten the hose clamps at this point, you risk warping your exhaust.

    4

    Use a wrench and thread locker to bolt on the new exhaust mounting bracket that came with your Vance & Hines pipes.

    5

    Reinstall your retainer rings and clamps in your new exhaust. Loosely bolt your new exhaust to your exhaust manifold and exhaust support bracket. Put Teflon paste on the oxygen sensors and reinstall them in your new header pipes.

    6

    Tighten the bolts that attach your new exhaust to the exhaust headers and support bracket using a wrench. Attach your heat shields to the hose clamps with a flat-head screwdriver.

Read More.. >

Saturday, November 30, 2013

How to Time a Harley Davidson Motorcycle

How to Time a Harley-Davidson Motorcycle

Checking the timing on your Harley-Davidson motorcycle every 5,000 miles plays an important role in a comprehensive maintenance routine. As a Harley-Davidson engine ages, you must adjust the ignition timing to compensate for the wear of internal engine parts. Setting the timing correctly keeps your motorcycle running smoothly and efficiently. Maladjusted timing may result in sluggish performance, poor fuel economy and possible damage to internal engine components. Setting the timing is relatively easy and ensures the maximum life from the engine.

Instructions

    1

    Remove the crankcase timing plug using an Allen wrench, and expose the timing hole. The timing hole is located on the primary chain case side of the motor on the engine block and capped with a solid hex-head plug. Install a clear plastic timing hole plug to prevent oil splash.

    2

    Connect the positive terminal of an inductive timing light to the positive battery terminal of the motorcycle. Connect the negative terminal of the timing light to the negative terminal of the battery. Connect the inductive pickup probe of the timing light to the front cylinder spark plug wire.

    3

    Start the engine, and run it at idle. Point the timing light into the timing inspection hole. If the ignition is properly timed, the timing bar will align with the circular timing reference mark. The reference marks on a correctly timed engine will appear as a vertical bar through the center of the circle. Some models only have a timing reference mark on the flywheel of the motor; on these models, the engine is correctly timed when the reference mark is visible in the timing inspection hole.

    4

    Remove the timing cover from the right side of the motor with a Phillips screwdriver or Allen wrench, depending on your specific model. Loosen the the timing plate screws with a slotted screwdriver, and turn the timing plate to adjust the timing. Recheck the timing marks with the timing light. Tighten the timing plate screws, and install the cover.

    5

    Shut off the engine, and remove the timing light. Remove the clear plastic timing hole plug, and install the solid plug in the hole.

Read More.. >

Sunday, September 22, 2013

How to Troubleshoot the Fuel System on a Harley Davidson

How to Troubleshoot the Fuel System on a Harley-Davidson

In a carbureted Harley, gasoline flows from the gas station, to the gas tank, by gravity through the petcock to the carburetor, then to the intake valves after which it explodes. In a fuel-injected Harley the gas is pumped from the fuel tank to the fuel injectors, which spray the gasoline into the intake valves. The most likely components to malfunction in a fuel-injected bike are the fuel pump or any of the multiple electronic sensors on such a bike. The fuel system on a fuel-injected Harley is diagnosed electronically. Troubleshooting the fuel system on a carbureted Harley is less susceptible to electronic gremlins and may be more illustrative of what makes these vehicles go.

Instructions

    1

    Open the gas cap and smell the gasoline. Shine a flashlight into the tank. If you see water or diesel oil floating on top of the gasoline, you must drain the fuel from the carbureted Harley.

    2

    Disconnect the hose clamp that secures the fuel line to the petcock with a flat-head screwdriver. Replace the fuel line at the petcock with a 2-foot length of 1/4-inch rubber hose.

    3

    Insert the open end of the hose in an empty, 5-gallon gas can. Open the petcock to "reserve" and drain the fuel.

    4

    Unscrew the petcock from the bottom of the fuel tank with an open-end wrench. Examine and, if necessary, clean the fuel filter.

    5

    Reinstall the petcock with an open-end wrench. Replace the fuel line on the petcock using a screwdriver and put 1 gallon of fresh gasoline in the fuel tank.

    6

    Open the petcock, open the choke, put the bike in neutral and attempt to start the motorcycle.

    7

    Open the throttle if the bike starts and fully close the choke. Run the motorcycle until the rocker box covers are warm to the touch and allow the throttle to return to normal idle. If the engine dies at a normal idling speed take the following steps.

    8

    Restart the motorcycle and idle the bike with the choke pulled halfway out. If the bike runs with the choke half out, but not pushed fully in, the fuel-air mixture in the carburetor has too much air and not enough gasoline.

Read More.. >