Showing posts with label 95. Show all posts
Showing posts with label 95. Show all posts

Friday, June 6, 2014

How to Troubleshoot a 95 Ci 2005 Harley Davidson

How to Troubleshoot a 95 Ci 2005 Harley Davidson

Harley Davidsons original compensator on 95-cubic-inch and larger twin cams may have been inadequate for the added torque produced by the newer engine. Harley now factory installs more robust compensators. There are sometimes electronic problems with fuel injected Harleys that can be difficult to diagnose. The usual procedure for that is to retrieve and translate the trouble codes. Beyond that, troubleshooting a 95-cubic-inch twin cam is not very different from troubleshooting a flathead 45. The process always begins with throwing your leg over the bike and sitting down.

Instructions

    1

    Open the petcock and extend the choke. Turn the ignition key switch to "On," the handlebar run switch to "On" and start the motorcycle. If the starter does not operate, your battery is dead.

    2

    Shake the motorcycle from side to side and listen for gas sloshing in the fuel tank. If you hear sloshing and the starter turns over, but the bike does not start, check the spark plugs, the plug wires and the coil.

    3

    Inspect the spark plug wires for breaks, wear and corrosion from the coil to the plugs. Remove the front spark plug with a socket wrench and a spark plug socket and inspect the plug. If you see anything other than a perfectly intact plug with a light gray or tan coating on the electrodes, your spark plug must be replaced.

    4

    Start the motorcycle and idle in neutral until the rocker box covers under your left hand are warm to the touch. Ride the motorcycle.

    5

    Listen as you ride. If you hear knocks or pings and your spark plugs are in good shape then the gasoline in your fuel tank is bad. If you hear a typewriter chattering either your pushrods or your tappets are improperly adjusted. If you hear a squeal when you stopped your brakes are worn out.

    6

    Change gears. If the bike shifts hard, the shifter rod on the lower left side of the motorcycle may be bent. If the transmission jumps out of gear, the shifter forks in the transmission are improperly adjusted.

    7

    Brake to a stop. If the brakes do not hold, the brake fluid in your master cylinder is low.

Read More.. >

Wednesday, April 2, 2014

How to Replace the O2 Sensor in a 95 Pontiac Bonneville SSEI

The 1995 Pontiac Bonneville SSEI engine has one oxygen sensor that detects the oxygen saturation in the exhaust and relays the information to the engines computer to regulate the fuel consumption. When a sensor fails, the "Check Engine" or "Service Engine Soon" light may illuminate on your dash. If the light is on and your fuel mileage has significantly decreased, replace the sensor as soon as possible to save needless expense.

Instructions

    1

    Raise the hood of the Bonneville. Locate the oxygen sensor threaded into the exhaust manifold near the front of the engine compartment.

    2

    Pull the electrical connection apart to disconnect it from the sensor. Remove the sensor with a wrench.

    3

    Coat the threads of the new sensor with electrical anti-seize compound. Install it by hand to avoid cross-threading. Torque the sensor to 30 foot-pounds with a torque wrench.

    4

    Push the electrical connector together until it clicks. Lower the hood.

Read More.. >

Wednesday, March 12, 2014

How to Adjust a Parking Brake in a 95 Mx 5

How to Adjust a Parking Brake in a 95 Mx-5

You can adjust the parking brake on your 1995 Mazda MX-5 right from your home garage, saving time and money. You will know that its time to adjust your parking brake when the vehicle starts to slip when parked downhill. Adjusting the parking brake takes up the slack in the parking brake cable, allowing the parking brake to be more effective. You only need a few basic tools to do the job.

Instructions

    1

    Start the engine. Step on the brake pedal so it goes all the way to the floor four times. Shut off the engine.

    2

    Locate the center console cover between the drivers and passengers seats. Unhinge the hooks. Remove the cover by lifting up.

    3

    Find the adjuster nut attached to the parking brake cable. Tighten the nut with the wrench.

    4

    Lift up on the hand brake one click. Start the engine and look on the instrument panel to see that the parking brake light is on. Disengage the hand brake.

    5

    Put wheel chocks behind and in front of the front wheels. Lift up the rear end of the Mazda with a jack. Slide jack stands under the vehicle next to the two rear wheels. Lower the vehicle onto the stands.

    6

    Spin the rear wheels forward with your hands. If youve done the adjustment correctly, they should spin freely.

    7

    Raise up the vehicle, slide the jack stands out of the way and lower the car to the ground. Remove the jack and wheel chocks.

Read More.. >