Showing posts with label o2. Show all posts
Showing posts with label o2. Show all posts

Wednesday, April 2, 2014

How to Replace the O2 Sensor in a 95 Pontiac Bonneville SSEI

The 1995 Pontiac Bonneville SSEI engine has one oxygen sensor that detects the oxygen saturation in the exhaust and relays the information to the engines computer to regulate the fuel consumption. When a sensor fails, the "Check Engine" or "Service Engine Soon" light may illuminate on your dash. If the light is on and your fuel mileage has significantly decreased, replace the sensor as soon as possible to save needless expense.

Instructions

    1

    Raise the hood of the Bonneville. Locate the oxygen sensor threaded into the exhaust manifold near the front of the engine compartment.

    2

    Pull the electrical connection apart to disconnect it from the sensor. Remove the sensor with a wrench.

    3

    Coat the threads of the new sensor with electrical anti-seize compound. Install it by hand to avoid cross-threading. Torque the sensor to 30 foot-pounds with a torque wrench.

    4

    Push the electrical connector together until it clicks. Lower the hood.

Read More.. >

Sunday, March 23, 2014

How Do I Replace an O2 Sensor in a 1998 Chevy Blazer

How Do I Replace an O2 Sensor in a 1998 Chevy Blazer?

The 1998 Chevy Blazer has three oxygen (O2) sensors. Two are located up on the front Y-pipe bolted to the V-6 engines manifold. These two sensors detect the fuel-to-air mix in the exhaust and transmit that information to the powertrain control module (PCM). From there, the PCM makes adjustments to achieve the lowest emissions possible while still running properly. The last O2 sensor is located after the catalytic converter. This sensors job is to monitor the efficiency of the catalytic converter.

Instructions

    1

    Apply the parking brake to lock the rear wheels.

    2

    Open the hood to the 1998 Chevy Blazer to allow some light down into the engine compartment. This will be helpful when under the vehicle to replace the front oxygen sensor(s). If you are replacing the rear sensor, opening the hood is not necessary.

    3

    Lift one front side of the Blazer up high enough to rest it on a jack stand and then lift the other side and rest that side on a jack stand.

    4

    Put on the safety glasses and crawl underneath the Blazer to locate the oxygen sensor(s) being replaced. One is located on the left-side Y-pipe up near the manifold connection, the other is on the right-side Y-pipe near the manifold and the rear sensor is located in the catalytic converter pipe just behind the shell of the converter.

    5

    Unlock the wire harness plug from the O2 sensor plug. Use the small screwdriver to press inward and release the lock while pulling the O2 sensor plug and wire away from the wire harness plug.

    6

    Spray penetrating oil around the threaded connection of the O2 sensor where it screws into the O2 sensor port of the exhaust piping. Allow the oil a few minutes to soak in.

    7

    Thread the O2 sensor wire through the closed end of the 22 mm wrench and then place the closed end of the wrench onto the sensors hex-head. Turn the wrench to the left (counterclockwise) to remove it from the port. Remove the sensor.

    8

    Inspect the threads of the replacement sensor. Most will come with a light coating of special anti-seize compound already on the threads. Some O2 sensor manufacturers will provide a small tube inside the box. If applying the compound, be sure to avoid getting the compound on the thimble-tip of the sensor. Only place a small amount on the threads of the sensor.

    9

    Thread the sensor into the port by hand to avoid crossing the threads of the sensor. Tighten the sensor with the wrench after threading the wire through the closed end again. Only tighten the sensor snugly. Over-tightening the sensor risks stripping the threads of the sensor and/or possibly damaging the threads to the sensor port.

    10

    Connect the replacement sensor wire plug to the wire harness plug before crawling out from under the Blazer with the tools and old sensor(s) and lowering the vehicle.

Read More.. >

Friday, January 10, 2014

How to Replace an O2 Sensor on an Aurora

The oxygen (O2) sensors on an Oldsmobile Aurora are a series of small sensors placed in the exhaust system that monitor the amount of unburned oxygen in the exhaust. The O2 sensors relay this information to the engines computer so it can make adjustments to help the engine to run more efficiently and lower vehicle emissions. The Aurora is equipped with four O2 sensors, one in each exhaust manifold, one between the exhaust manifold and catalytic converter, and one after the catalytic converter. You can use a diagnostic code scanner to determine which sensor is malfunctioning. If you do not own a code scanner, take your Aurora to an auto parts store; many have code scanners and will check your car for free.

Instructions

    1

    Disconnect the ground cable from the negative battery terminal by loosening the retaining bolt and pulling the clamp off the negative terminal. Secure the ground cable so that it cannot accidentally contact the negative battery terminal.

    2

    Raise the vehicle and support it with jack stands underneath the frame.

    3

    Disconnect the wiring harness from the sensor. Follow the wires connected to the sensor until you find a plastic wiring connector. Separate the wiring harness by pulling the connector apart.

    4

    Use a wrench to remove the sensor from the exhaust pipe or manifold.

    5

    Thread the new O2 sensor into the exhaust pipe or manifold, and tighten it.

    6

    Connect the wiring harness on the new O2 sensor to the plastic wiring connector that you removed from the old O2 sensor.

    7

    Lower the vehicle.

    8

    Reconnect the ground cable to the negative battery terminal. Tighten the retaining bolt that secures the ground cable to the negative battery terminal.

Read More.. >

Wednesday, December 4, 2013

How to Compare O2 Sensors

How to Compare O2 Sensors

A vehicles Powertrain Control Module adjusts the ratio of air and fuel so a vehicle gets the best possible fuel economy. This 02 sensor constantly signals the PCM to inform it of the status of the air and fuel mixture. More than one type of 02 sensor is available for installation.

Zirconia

    The most common 02 sensor is the zirconia type; it comes in either heated or unheated versions. Unheated zirconia 02 sensors take a few minutes to work, because they rely on a vehicles exhaust to heat up before they produce a signal. Heated zirconia 02 sensors have a heater circuit inside them. They work in about 60 seconds or less.

Titania

    Titania 02 sensors are made up of a different type of ceramic than that found in zirconia 02 sensors. It uses resistance changes to notify the PCM. Only a few vehicles come equipped with Titania 02 sensors.

Wide-band

    The signal produced by wide-band 02 sensors switch in direct proportion to the ratio of the air and fuel mixture. The PCM keeps a constant air-to-fuel ratio just by adding or taking away fuel when needed.

Read More.. >

Wednesday, September 25, 2013

How to Replace O2 Sensors in a 1997 Ford Explorer

Your 1997 Ford Explorer has two oxygen sensors built into the exhaust system. The oxygen sensors monitor the amount of oxygen in the exhaust to help the truck regulate how much fuel it burns. When an oxygen sensor fails, your truck may burn more fuel than necessary, reducing your fuel mileage drastically. You can replace the oxygen sensors quickly in your own driveway. Buy new sensors from an auto parts store or a Ford dealership.

Instructions

    1

    Raise your Explorer with a jack and secure it on a set of jack stands. Locate the oxygen sensors on the exhaust positioned before and after the catalytic converter.

    2

    Disconnect the wiring harness from the oxygen sensor by pulling the connector straight off. Use an oxygen sensor socket and ratchet to remove the oxygen sensor from the exhaust pipe.

    3

    Install the new oxygen sensor by hand to avoid cross threading the sensor. Once the sensor is secure, tighten it with the oxygen sensor socket and ratchet.

    4

    Press the wiring harness connector onto the new sensor until it is secure. The wiring harness should click when it is secure.

    5

    Repeat the process for the second oxygen sensor if you are replacing both. Raise the vehicle with the jack and remove the jack stands. Lower the truck to the ground.

Read More.. >