Friday, March 21, 2014
How to Install an Electric Fuel Pump in a 1997 Ford 7 3
A 1997 Ford vehicle may have a variety of engine sizes, including an 8-cylinder 7.3-liter diesel engine. This engine is in the larger pickup trucks, such as a F-250 or F-350. The 1997 Ford 7.3-liter engine uses fuel injection and requires a high-pressure electric fuel pump. The fuel pump in a Ford diesel engine is accessible from the engine compartment and its replacement requires you to first relieve the pressure in the fuel system.
Instructions
- 1
Disconnect both ground cables from the battery with a socket wrench to prevent accidental sparking from the battery. Loosen the filler cap for the fuel tank by 1/2 turn to relieve the pressure in the fuel tank. Open the filler cap completely.
2Raise the vehicle with a floor jack and support it on jack stands. Locate the electrical connector for the fuel pump in the engine compartment. It is behind the fuel pump and next to the frame rail. Detach the electrical connector from the fuel pump.
3Locate the retaining clip for the fuel line to the fuel pump. Slide the retaining clip off of the quick connect fitting for the fuel line. Remove the fuel pumps fuel line from the fuel pump with the fuel line tool.
4Remove the clips for the brake line from the bracket of the fuel pump. Disconnect the pinch bolt on the mounting bracket with a socket wrench and spread the bracket open. Detach the fuel pump from its mounting bracket.
5Install the new fuel pump by performing steps one through four in reverse order. Start the engine and check for fuel leaks.
Wednesday, January 15, 2014
How to Adjust Emergency Brake Cables on a 1997 F150
You can adjust the emergency brake cables on your 1997 Ford F-150 yourself right from your home garage or driveway. This will save you a trip to the mechanic. When you park your F-150 on a downhill slope and the parking brake starts to slip, you know its time to adjust the cables on the parking brake. You just need a couple of tools purchased from your local auto parts retailer to get the job done. Start by parking the vehicle on level ground before making the adjustment.
Instructions
- 1
Step on the parking brake pedal, pressing it all the way to the floor.
2Place wheel chocks in front of the front wheels and chocks behind the front wheels.
3Put the floor jack under the back end of the vehicle and lift it up high enough to slid the jack stands underneath the F150 next to each wheel. Lower the vehicle onto the jack stands.
4Get under the Ford and find the parking brake cable rod in the center of the vehicle. It is the rod with the cables coming to it. Hold the rod in place with your hand. Using pliers, tighten the equalizer nut about six turns.
5Attach the cable tension gauge to the rear tension cable to measure and set the number of pounds of tension. Set the F-150s tension at 350 pounds.
6Disengage the parking brake and spin the rear wheels to make sure they turn freely.
7Adjust the parking brake equalizer nut so that it has a clearance of 0.38 mm if you find there is resistance when you spin the wheels.
8Raise up the truck, remove the jack stands, lower the vehicle to the ground and remove the wheel chocks.
Friday, January 10, 2014
How to Replace a 1997 Ford F 150 Heater Core
The heater core in your 1997 Ford F-150 is a radiator-style unit used to heat the interior of your truck. Coolant flows from the lower radiator hose to and through the heater core. This fluid heats the unit, and a blower fan forces warm air through the core and into the cabin when the heater is turned on. A faulty or clogged heater core will leak coolant onto the inside floorboard on the front passengers side. Replacing the heater core can be a complicated and time-consuming repair because of its location behind the passengers side dashboard.
Instructions
- 1
Raise the hood and disconnect both battery cables using a crescent wrench. Slide the recycling container underneath the radiator drain plug.
2Remove the radiator fill cap. Loosen the radiator drain plug using a socket wrench to drain the radiator coolant. Once drained, replace the plug and tighten. Keep the recycling container in place to capture the excess coolant in the lower radiator hose.
3Disconnect the lower radiator hose where it attaches at the radiator by loosening the squeeze-type hose clamp. Allow the excess fluid to drain into the recycling container.
4Locate the heater core intake and return hose lines that protrude through the passengers side firewall of the engine compartment. Disconnect the hoses from the core nipples by depressing the release clip with a flat-head screwdriver while turning the hose counterclockwise by hand.
5Detach the Torx screws under the front dashboard that hold the dashboard soft cover in place. Reach under the dashboard and remove the mounting bolts attaching the dashboard frame to the interior firewall. This will allow the entire dashboard assembly to swing free and give you enough clearance to access the heater cover and core downward from the windshield.
6Detach the interior heater core intake and return hoses from the core nipples by releasing the squeeze clamps using channel-lock pliers. Remove the hoses by twisting as you pull. Disconnect the heater core ground cable strap that attaches to the interior firewall with a single bolt.
7Take out the four outer mounting bolts holding the heater core cover in place. Remove the four mounting bolts attaching the actual heater core to the interior firewall. Maneuver the old unit out and up toward the windshield. Be careful not to spill the coolant inside the heater core.
8Install the replacement heater core in reverse, downward from the windshield and behind the dashboard. Re-mount the heater core, the core cover and the ground cable strap.
9Reattach the intake and return hoses carefully to the core nipple on the firewall. The nipple hoses are different diameters to prevent you from incorrectly crossing the connection hoses.
10Connect the dashboard frame and cover in reverse of the removal. Tighten all the mounting bolts. Be sure that the airbag remained connected during the repair. If it didnt, reconnect as necessary.
11Reconnect the hoses located in the engine compartment at the firewall core nipple by snapping the hoses in place. Connect the lower radiator hose to the radiator and secure it in place using its squeeze-type hose clamp.
12Refill the radiator with a 55/45 mixture of new anti-freeze and distilled water. Reconnect the battery and start the engine. Run the engine for several minutes to flush out any trapped air within the cooling system.
13Test the replacement heater core by turning the heater on and off continually, observing the change in temperature. Check for leaks at all hose connections.
Thursday, November 28, 2013
How Do I Change an Oxygen Sensor on a 1997 Hyundai Accent GL
The 1997 Hyundai Accent oxygen sensor threads into the exhaust manifold beneath the heat deflector under the car. The O2 sensor regulates the fuel consumption of the engine based upon the oxygen saturation of the exhaust. If the gas mileage in your car has inexplicably decreased substantially and the check engine light is on, you may have a failing O2 sensor. Buy a replacement sensor at an auto parts store or Hyundai dealership.
Instructions
- 1
Raise the Accent with a jack. Rest the car on a set of jack stands.
2Disconnect the wiring harness from the O2 sensor just beneath the exhaust manifold heat deflector.
3Remove the bolts on the outer edge of the heat deflector with a socket and ratchet. Set the heat deflector and bolts aside in a safe location. Remove the O2 sensor with an O2 sensor socket and ratchet.
4Install the new sensor by hand to avoid cross threading it. Tighten the sensor with an oxygen sensor socket and ratchet. Reconnect the wiring harness on the O2 sensor by pressing it into place.
5Replace the heat deflector. Secure the deflector with the bolts and tighten the bolts with a socket and ratchet.
6Raise the car slightly with a jack and remove the jack stands. Lower the car to the ground.
Wednesday, November 20, 2013
How to Replace the Radiator in a 1997 Silverado
Replacing the radiator in your 1997 Silverado is a basic automotive repair to perform. Your radiator plays an important role in the trucks overall cooling system. Its primary function is to keep the engine from overheating. As your engines temperature rises, a cooled mixture of coolant flows into the engine and reduces its temperature. Over time, the radiator becomes damaged resulting from objects hitting the front during operation. This damage can cause the water not to properly flow into the engine as necessary. Performing a routine inspection for damage can help prevent your radiator from falling and causing engine overheating.
Instructions
Removal
- 1
Park the truck on a level surface, and set the parking brake. Lift the front end using a floor jack, and carefully place it onto the jack stands. Brace the rear wheels using wheel chocks as an added safety measure.
2Raise the hood, remove the radiator fill cap and disconnect the negative battery cable. Place the recycling container under the radiator drain plug.
3Unscrew the drain plug bolt, and drain all of the antifreeze from the radiator. Securely seal the recycling container, and safety move it to the side.
4Remove the radiator safety shield (shroud) mounted on the top of the radiator. The shroud is held in place using two bolts on either side.
5Remove the main intake radiator hose that attaches to the thermostat housing cover. This hose is held in place by a squeeze-type hose clamp. Detach the hose that leads to the antifreeze reservoir tank.
6Make note of the lower hose connections, which include the radiator hose leading to the water pump, and also the heater core hose line. Disconnect these lower hoses held in place by squeeze clamps.
7Reach underneath the truck, and remove the lower radiator mounting bolts. Then, take out the upper mounting bolts from the engine compartment and lift out the radiator.
Installation
- 8
Carefully hold the replacement radiator in place, and screw in the upper mounting screws by hand. This will hold the radiator in place and allow you to install the lower bolts.
9Install the lower bolts, and securely tighten all of the mounting bolts in place. Reconnect the lower radiator and heater core hoses, and secure them in place using the hose clamps.
10Connect the upper radiator and reservoir hoses and secure them using the hose clamps. Re-mount the safety shield (shroud), and secure it in place using its mounting bolts.
11Start the engine, and fill the radiator with a new 50/50 mixture of antifreeze and water. Let the engine idle for several minutes to bleed out trapped air within the cooling system. Replace the radiator fill cap, and inspect all the connections for leaks.
12Safely raise the truck and remove the floor jacks and wheel chocks. Lower the truck to the ground.
Thursday, October 31, 2013
1997 Chevy Lumina Problems
Problems with the 1997 Chevy Lumina have led to safety recalls by General Motors and consumer complaints to the National Highway Traffic Safety Administration (NHTSA). Issues range from engine trouble to difficulties with power steering.
Steering
Power steering problems in the 1997 Chevy Lumina resulted in a safety recall in 2003. A manufacturing mistake in the lower pinion bearings may allow the ball bearings to fall out, which may lead the driver to have to exert extra force when trying to turn the wheel. In some cases, turning left may be nearly impossible.
Fuel System
A manufacturing defect in certain aftermarket Delphi fuel pressure regulators used in select 1997 Chevrolet Lumina vehicles may cause a fuel leak that could lead to a fire. These filters were recalled in 2007.
Transmission
Various 1997 Lumina transmission problems have been reported by consumers to the NHTSA and addressed in Technical Service Bulletins by the manufacturer. These include transmission oil leaks, slipping and erratic/intermittent shifting, and going out of drive and into neutral. Edmunds.com reports that occasional problems with this vehicles TCC (torque converter clutch) regulator valve may "feel like an engine miss while driving between 40 and 60 mph." As of 2010, no recalls have resulted from these problems.
Engine
Engine problems in the 1997 Chevy Lumina, as addressed by Technical Service Bulletins, include problems with rough idling and intermittent misfires. Consumers have reported to the NHTSA problems with engine mounts falling out and coolant from the manifold leaking into the engine. No recalls have resulted from these issues, as of 2010.
Tuesday, October 8, 2013
How to Fix a Windshield Washer Pump on a 1997 Chevy C 1500 Truck
When the windshield washer pumps fail on a 1997 Chevrolet Silverado 1500, the windshield washer system cannot transfer fluid through the system tubing in order to clean the windshield. These pumps, located in the windshield washer tank, are the sole components responsible for moving fluid throughout the entire system. These pumps operate by running off the vehicles 12 volt electrical power supply. When the wash section of the windshield wiper arm is depressed, the wiper motor relay switches to a closed position allowing current to flow to the washer pumps. In the event of a pump failure, current still flows to the pump, but they will not operate.
Instructions
Removal
- 1
Remove the bolts holding the washer tank area cover to the truck with a metric ratchet and socket. Remove the two bolts holding the washer tank to the truck body with a metric socket and ratchet.
2Unplug the upper pump hose from the vehicle. Disconnect the electrical connector from the truck to the pump assembly. Lift the washer tank out of the truck. Pour the washer fluid from the tank into a drain pan.
3Pry the washer pump cover away from the washer tank with a flat-head screwdriver, and then set it aside. Disconnect the electrical connectors from the washer pumps. Disconnect the washer pump hose from the individual washer pumps.
4Twist and pull on each washer pump to remove it from its mounting grommet.
Installation
- 5
Set the new washer pumps into position and press down on them until they are completely seated in the rubber grommet holes. Reconnect their electrical connectors. Reconnect the wash pump hose to each pump.
6Snap the pump cover onto the washer tank. Set the tank back into the truck and reinstall the bolts holding the tank to the truck. Torque the bolts to 53 inch-pounds with a torque wrench. Reconnect the upper pump hose to the hose running to the washer jets.
7Refill the washer tank with new fluid and close the cover. Set the washer tank area cover into place and reinstall the bolts holding it in place with a metric socket and ratchet. Test the washer pumps.
Wednesday, October 2, 2013
How to Install the 1997 Volvo 850 Oxygen Sensor
The 1997 Volvo 850 is equipped with two oxygen sensors along the exhaust system. The sensors thread into the exhaust pipes in front of and behind the catalytic converter. The sensors monitor the amount of oxygen in the exhaust to notify the cars fuel system to adjust the amount of fuel burned by the engine. When a sensor fails, the "Check Engine" light will illuminate and your fuel mileage will substantially decrease. Buy new sensors from an auto parts retailer and change them at home for a cost-effective repair.
Instructions
- 1
Open the hood of your 850. Loosen the negative battery cable with a wrench and lift it off the terminal.
2Raise the car with a jack and stabilize it on jack stands. Locate the oxygen sensors on either side of the catalytic converter.
3Disconnect the electrical wiring harness on the sensor by pressing the retaining tab and pulling the connector apart.
4Remove the sensor with a wrench or ratchet and oxygen sensor socket. Spread anti-seize compound on the threads of the new sensor. Install the new sensor by hand.
5Tighten the sensor using a wrench or oxygen sensor socket and ratchet set. Press the electrical connection together until it clicks. Repeat the process on the second sensor if needed.
6Raise the car with the jack so you can remove the jack stands. Return the car to the ground. Attach the negative battery cable and tighten it with a wrench. Close the hood.
Wednesday, September 25, 2013
How to Replace O2 Sensors in a 1997 Ford Explorer
Your 1997 Ford Explorer has two oxygen sensors built into the exhaust system. The oxygen sensors monitor the amount of oxygen in the exhaust to help the truck regulate how much fuel it burns. When an oxygen sensor fails, your truck may burn more fuel than necessary, reducing your fuel mileage drastically. You can replace the oxygen sensors quickly in your own driveway. Buy new sensors from an auto parts store or a Ford dealership.
Instructions
- 1
Raise your Explorer with a jack and secure it on a set of jack stands. Locate the oxygen sensors on the exhaust positioned before and after the catalytic converter.
2Disconnect the wiring harness from the oxygen sensor by pulling the connector straight off. Use an oxygen sensor socket and ratchet to remove the oxygen sensor from the exhaust pipe.
3Install the new oxygen sensor by hand to avoid cross threading the sensor. Once the sensor is secure, tighten it with the oxygen sensor socket and ratchet.
4Press the wiring harness connector onto the new sensor until it is secure. The wiring harness should click when it is secure.
5Repeat the process for the second oxygen sensor if you are replacing both. Raise the vehicle with the jack and remove the jack stands. Lower the truck to the ground.