Showing posts with label volvo. Show all posts
Showing posts with label volvo. Show all posts

Tuesday, May 6, 2014

How to Reset the Traction Control Light on the 2000 V70 Volvo

The Volvo V70 wagon is equipped with an advanced traction control system that actively monitors the wheels to ensure proper traction. When the system senses a loss of traction, it retards the engine timing until traction increases. The entire traction system is monitored and controlled by the ABS computer. When the ABS computer detects an issue with the traction control system, it turns on the traction control light. In addition to turning on this light, it records a trouble code that corresponds directly to the problem. Automotive technicians can retrieve this trouble code with an automotive scan tool in order to diagnose and repair the system. In order to reset the traction control light, this code must be erased from the ABS computers memory.

Instructions

    1

    Stop the engine and turn the ignition forward to the RUN position so that the dashboard lights are illuminated.

    2

    Find the V70s communications port under the dashboard on the drivers side of the passenger cabin. This port is a 16-pin receptacle that is mounted just out of view, under the leading edge of the dashboard.

    3

    Plug the scan tools connector into the communications port. Turn on the scan tool and wait while it starts up. Most scan tools run an automatic check of their memory, similar to home computers, before arriving at the menu screen.

    4

    Look caully at the scan tools screen. Use the menu button on the scan tool to navigate to the ABS menu. Select the option to clear the trouble codes from the ABS computers memory. Watch the screen for a confirmation message that the codes are cleared.

    5

    Use the menu keys to navigate back to the home screen and power down the scan tool. Disconnect the cable from the communication port and start the engine. Verify that the traction control light is not on or blinking. If the light is off then the traction control system is reset.

Read More.. >

Sunday, March 2, 2014

Ashtray Removal for a Volvo 850

The Volvo 850 is a compact luxury car that was manufactured from 1992 to 1997. The 850 was the first front-wheel drive car from Volvo to be exported to the United States. Standard 850 interior accessories include power windows and door locks, tilt/telescopic steering column, air conditioning, cruise control and a CD-ready, AM/FM cassette stereo system. The ashtray is below the stereo. A second ashtray is on the back of the center console, behind the front seats. Both ashtrays are easy to remove, requiring no tools.

Instructions

    1

    Look for the panel below the radio. It has the word "PUSH" on it. Press lightly on the panel to open it.

    2

    Put your fingers on the sides of the removable gray tray part of the ashtray and push it back.

    3

    Pull up on the tray and remove it from the dash. The tray is the only part that can be removed for cleaning.

    4

    Pull out on the rear ashtray to open it, and then lift up on the rear edge to remove it.

Read More.. >

Sunday, January 19, 2014

Taillight Installation on a 1991 Volvo Wagon

Replace the taillights of your 1991 Volvo station wagon with new PB17916 dual filament bulbs if one stops working. You can buy these bulbs at any auto parts store, and they are usually in-stock items. You wont need any tools, and you can access the spent bulbs from the cargo area of the car through an access panel directly behind the lights. On some models, you may need to remove the spare tire to open the right-side access panel.

Instructions

    1

    Open the rear lift gate of your Volvo wagon and locate the access panel just inside the gate opening directly behind each taillight in the cargo area. Turn the two retaining clips on the access panel to open it.

    2

    Locate the bulb holder inside the access hole and release the retaining clips on either side of the holder. Pull the holder straight out of the taillight housing and turn it so the bulbs are facing you.

    3

    Push in slightly on the bulb while rotating it counterclockwise, then remove it from the holder and discard it. Install a new BP17916 bulb; press in on the bulb and rotate it clockwise to lock it in place.

    4

    Insert the bulb holder into the back of the taillight assembly, pushing it in until the locking tabs snap in place. Close the access panel and turn the two retaining clips to secure the cover.

    5

    Close the rear lift gate and test the repair by turning on the headlight switch or pushing the brake pedal while someone monitors the taillight function.

Read More.. >

Saturday, December 21, 2013

Volvo 960 Liquid Gasket Removal

Volvo 960 Liquid Gasket Removal

The valve cover on the Volvo 960 is finely machined and does not use a solid gasket as with most vehicles. Volvo instead requires the use of a liquid gasket. When you do any work requiring removal of the valve cover, a new liquid gasket should be applied. This necessitates removal of the old gasket. The process is tedious, but not difficult.

Instructions

    1

    Read the instructions for using the liquid gasket remover. Open the valve cover and expose the two surfaces where the liquid gasket was applied. Apply the gasket remover liberally on both surfaces and allow them to soak for approximately 10 minutes.

    2

    Using the razor blade, carefully scrape the surfaces to remove the old gasket. Employ the putty knife in places where the razor blade wont fit. Continue to scrape, until all of the old gasket is gone. Wipe the surfaces clean with the shop cloth.

    3

    Apply the gasket remover to both surfaces a second time and allow them to soak. Scrape the surfaces gently with either the razor blade or the putty knife and ensure that the entire surface has been cleaned of the old gasket. Wipe both surfaces with a shop cloth.

Read More.. >

Thursday, December 5, 2013

How to Replace a Fuel Injector for a 1992 940 GL Volvo

The Volvo 900 series is a range of mid-size cars made by Volvo during the 1990s, and the 940 models were in production from 1991 to 1997. The 1992 940 GL had a four-cylinder 2.3-liter engine with electronic fuel injection. These fuel injectors deliver a precise ratio of fuel and air to the engine at high pressure. The fuel injectors on the 1992 Volvo 940 GL are on top of the engine and are accessible from the engine compartment.

Instructions

    1

    Remove the fuel pump relay under the dashboard and start the engine. Allow the engine to idle until it stalls to relieve the pressure in the fuel system. Turn the ignition off and replace the fuel pump relay.

    2

    Disconnect the negative battery cable with a socket wrench to prevent the accidental discharge of fuel. Detach the fuel lines and electrical connectors from the fuel injection manifold. Remove the vacuum hose from the fuel pressure regulator. Disconnect the fuel pressure regulator from the bracket of the fuel rail with a socket wrench.

    3

    Remove the retaining bolts for the fuel injection manifold with a socket wrench. Detach the fuel injection manifold and fuel injectors from the engine as an assembly. Secure the fuel injection manifold in place on a work bench and disconnect the fuel injectors from the manifold.

    4

    Remove the O-rings from the fuel injectors and replace them if they show signs of wear. Apply a thin layer of petroleum jelly to the O-rings, and install them onto the new fuel injectors. Connect the fuel injector to the fuel injection manifold and install this assembly onto the engine. Tighten the retaining bolts for the fuel injection manifold with a socket wrench.

    5

    Connect the fuel pressure regulator to the fuel rail bracket and attach the vacuum hose to the fuel pressure regulator with a socket wrench. Connect the fuel lines and electrical connectors to the fuel injection manifold. Connect the cable to negative terminal of the battery. Start the engine and check for fuel leaks.

Read More.. >

Monday, November 11, 2013

Volvo Engine Problems

Volvo Engine Problems

Volvo cars are renowned for their safety and dependability. However, like all cars, they have engine trouble and break down from time to time. If yours isnt working, you can try a few simple tests to get it running again.

Check the Battery

    Always use caution when working with jumper cables.
    Always use caution when working with jumper cables.

    If your Volvo engine will not start, the problem could be a dead battery. Batteries can die from reasons ranging from a faulty alternator to leaving the interior light on overnight. If you suspect your battery might be dead, you can either check it with a volt meter or try to jump it using jumper cables and another vehicle.

Check the Gas Level


    If jumping the car off doesnt work or you find the battery to be functioning, be sure the car has sufficient fuel in the tank. If the electronics are still functioning normally the fuel gauge should indicate whether or not this is the case. If the gauge doesnt work, check the gas manually or simply add some to the tank and try starting the car.

Call a mechanic

    If the battery is functioning and the tank has gas and your car still wont start, it might be time to contact a mechanic. If you cant get the car running at all you may need to call a tow truck or hire a mechanic who will come to check your Volvo. You should be sure to find a mechanic who specializes in imported or Volvo cars.

Read More.. >

Wednesday, October 2, 2013

How to Install the 1997 Volvo 850 Oxygen Sensor

How to Install the 1997 Volvo 850 Oxygen Sensor

The 1997 Volvo 850 is equipped with two oxygen sensors along the exhaust system. The sensors thread into the exhaust pipes in front of and behind the catalytic converter. The sensors monitor the amount of oxygen in the exhaust to notify the cars fuel system to adjust the amount of fuel burned by the engine. When a sensor fails, the "Check Engine" light will illuminate and your fuel mileage will substantially decrease. Buy new sensors from an auto parts retailer and change them at home for a cost-effective repair.

Instructions

    1

    Open the hood of your 850. Loosen the negative battery cable with a wrench and lift it off the terminal.

    2

    Raise the car with a jack and stabilize it on jack stands. Locate the oxygen sensors on either side of the catalytic converter.

    3

    Disconnect the electrical wiring harness on the sensor by pressing the retaining tab and pulling the connector apart.

    4

    Remove the sensor with a wrench or ratchet and oxygen sensor socket. Spread anti-seize compound on the threads of the new sensor. Install the new sensor by hand.

    5

    Tighten the sensor using a wrench or oxygen sensor socket and ratchet set. Press the electrical connection together until it clicks. Repeat the process on the second sensor if needed.

    6

    Raise the car with the jack so you can remove the jack stands. Return the car to the ground. Attach the negative battery cable and tighten it with a wrench. Close the hood.

Read More.. >