Showing posts with label 2000. Show all posts
Showing posts with label 2000. Show all posts

Saturday, May 17, 2014

How to Install a Timing Belt for a 2000 Ford Focus

The Ford Focus is a compact car that Ford began manufacturing for the 2000 model year in North America. The engine for a Ford Focus made before 2005 is a four-cylinder 2.0-liter engine with a double overhead camshaft. This type of engine uses a timing belt instead of a timing chain, and requires you to replace the timing belt at regular intervals. The timing belt for a 2000 Ford Focus allows the crankshaft to turn the camshaft.

Instructions

    1

    Remove the cable from the negative battery terminal with a socket wrench to prevent you from inadvertently starting the engine. Disconnect the accessory drive belt and its tensioner. Remove the cover for the timing belt.

    2

    Loosen the lug nuts for the right front wheel with a lug wrench. Raise the vehicle and support it on jack stands. Remove the right front wheel and the right splash shield with a socket wrench. Disconnect the pulley for the crankshaft.

    3

    Turn the timing belt clockwise so that the timing marks on the camshaft and crankshaft sprockets align with their respective marks on the engine.

    4

    Loosen the bolt for the timing belt tensioner with a socket wrench. Turn the tensioner 1/4 turn counterclockwise with an 8mm Allen wrench. Place a 1/8 in. drill bit into the hole of the timing belt tensioner to hold the tensioner in place. Remove the timing belt from the camshaft sprocket and crankshaft sprocket.

    5

    Place the new timing belt on the crankshaft. Complete the timing belt installation by proceeding in a counterclockwise direction. Remove the drill bit from the timing belt tensioner hole to release the tensioner.

    6

    Turn the crankshaft clockwise by two complete turns to align the timing marks once again. Tighten the bolt for the timing belt tensioner to between 15 and 22 pounds with a torque wrench.

    7

    Connect the crankshaft pulley and tighten its mounting bolt to between 81 and 96 ft. lbs. with a torque wrench. Connect the right splash shield and right front wheel with a socket wrench.

    8

    Lower the vehicle and tighten the lug nuts with a lug wrench. Install the accessory drive belt and its tensioner with a socket wrench. Attach the cable to the negative battery terminal.

Read More.. >

Tuesday, May 13, 2014

2000 Durango Alignment Specs

2000 Durango Alignment Specs

Produced by Dodge, Durango is a full-sized sport utility vehicle (SUV). It can be equipped with several different Hemi engines. The two powerhouse V-8 engines used in Durango vehicles are the 5.7-liter and the 5.9-liter engine. All Durango SUVs require periodic adjustment, often erred to as "alignment." The factory specifications for the alignment are the same for all 2000 Durango models.

Caster

    Caster is both the rearward and the forward tilt of the steering knuckle from the true vertical. Caster is the measurement in angles that is responsible for directional stability. The Durango caster angle should be the same on both left and right wheels. The angle must be +3.10 degrees with the maximum allowable difference of 0.50 degrees on the two-wheel drive (2WD) model and +3.30 degrees with the measuring accuracy of 0.50 on the four-wheel drive (4WD) model.

Camber

    Measured in degrees, camber is the outward or inward tilt of the wheel in relation to the center of the vehicle. The Durango camber angle should be the same on both left and right wheels. Camber angles must be -0.25 degrees with the measuring accuracy of 0.50 degrees both for the 2WD and 4WD models.

Toe

    Toe is the difference between the leading and trailing inside edges of the front wheels. Total angles on the 2WD and 4WD models must be +0.10 degrees with measuring range of 0.06 degrees.

Read More.. >

Tuesday, May 6, 2014

How to Reset the Traction Control Light on the 2000 V70 Volvo

The Volvo V70 wagon is equipped with an advanced traction control system that actively monitors the wheels to ensure proper traction. When the system senses a loss of traction, it retards the engine timing until traction increases. The entire traction system is monitored and controlled by the ABS computer. When the ABS computer detects an issue with the traction control system, it turns on the traction control light. In addition to turning on this light, it records a trouble code that corresponds directly to the problem. Automotive technicians can retrieve this trouble code with an automotive scan tool in order to diagnose and repair the system. In order to reset the traction control light, this code must be erased from the ABS computers memory.

Instructions

    1

    Stop the engine and turn the ignition forward to the RUN position so that the dashboard lights are illuminated.

    2

    Find the V70s communications port under the dashboard on the drivers side of the passenger cabin. This port is a 16-pin receptacle that is mounted just out of view, under the leading edge of the dashboard.

    3

    Plug the scan tools connector into the communications port. Turn on the scan tool and wait while it starts up. Most scan tools run an automatic check of their memory, similar to home computers, before arriving at the menu screen.

    4

    Look caully at the scan tools screen. Use the menu button on the scan tool to navigate to the ABS menu. Select the option to clear the trouble codes from the ABS computers memory. Watch the screen for a confirmation message that the codes are cleared.

    5

    Use the menu keys to navigate back to the home screen and power down the scan tool. Disconnect the cable from the communication port and start the engine. Verify that the traction control light is not on or blinking. If the light is off then the traction control system is reset.

Read More.. >

Sunday, April 20, 2014

How do I Replace a Timing Belt on a 2000 Hyundai Elantra

The Hyundai Elantra is a series of compact cars that Hyundai has manufactured since 1990. The 2000 model represents the last year of the second generation Hyundai, which had a 4-cylinder, 2.0-liter engine as its standard engine. This engine uses a timing belt to synchronize the movement of the camshaft and crankshaft as opposed to a timing chain. The timing belt in a 2000 Hyundai requires replacement approximately every 60,000 miles.

Instructions

    1

    Disconnect any components necessary to access the cover of the timing belt. Remove the timing belt cover with a socket wrench.

    2

    Turn the crankshaft clockwise to position the No. 1 piston at the top dead center position as indicated by the timing marks on the crankshaft. Disconnect the tensioner for the timing belt and the idler pulley with a socket wrench. Remove the timing belt from the camshaft sprocket and the crankshaft sprocket.

    3

    Turn the camshaft sprocket clockwise to align its timing marks and ensure the timing marks for the crankshaft timing are still aligned. Connect the tensioner for the timing belt with a socket wrench, but do not tighten the pulley bolt for the tensioner. Install the idler pulley and tighten its mounting bolt to between 32 and 41 foot-pounds.

    4

    Place the timing belt over the sprocket of the camshaft, then over the sprocket of the crankshaft. Turn the timing belt tensioner counterclockwise to place tension on the timing belt. Apply 5 pounds of force to the middle of the longest span of the timing belt. The deflection of the timing belt will be between 0.16 inches and 0.24 inches when the timing belt is at the correct tension.

    5

    Tighten the pulley bolt for the timing belt tensioner to between 32 and 41 foot-pounds with a torque wrench. Turn the crankshaft sprocket clockwise by one turn to align the timing marks on the crankshaft sprocket. Adjust the timing belt tension as required.

    6

    Replace the cover for the timing belt. Install any additional components that you removed in step one to access the timing belt.

Read More.. >

Monday, February 24, 2014

How to Repair the Rear Driver Side Window in a 2000 Malibu

How to Repair the Rear Driver-Side Window in a 2000 Malibu

Any broken window in a car can become a major frustration. Nobody wants to have to deal with the lack of security, unwanted objects flying inside your car, and noisy wind constantly blowing while you are driving. Rather than having to tape layers of plastic wrap over your broken window, or pay costly shop fees, you can replace the window with only a few tools.

Instructions

    1

    Remove the door trim panel. Use screwdriver and trim removal tool (or flat screwdriver) where appropriate to either unscrew pieces holding the trim on or pry them off where there are no screws. If your car has a manually operated window handle, use the trim removal tool to remove the handle. If your car has any electrical components located in the door trim, disconnect the electrical connectors as necessary to remove the trim. Remove the plastic water deflector that is between door and the trim panel.

    2

    Clean up any broken glass. Depending on how your old window broke, there may be pieces of broken glass inside your door. Use a broom or vacuum to remove these pieces of broken glass.

    3

    Remove the old window glass. Remove the window-to-channel nuts that are located at the bottom of the glass. You may have to lower the window glass to gain access to these nuts. Use the appropriate sized socket to remove the nuts. Place the nuts somewhere safe to avoid losing them. Remove the rubber sealing strip on the inside top of the door. Remove the old glass from the door by pulling it up and through where the rubber strip was.

    4

    Install the new window glass. Insert the new glass the same way that the old glass was removed. Put back on and tighten the window-to-channel nuts. Put back on the rubber seal that was removed. Put the door trim and any pieces that were removed with it, as well as the plastic water deflector, back on.

Read More.. >

Wednesday, February 5, 2014

How to Remove Spark Plug Wires From a 2000 Toyota Camry

Removing the spark plug wires from your 2000 Toyota Camry may be necessary to replace defective spark plug wires. The 2.2-liter engine uses four wires connected to the spark plugs on one end and one of two coils on the opposite end. The wires have specific lengths, so getting a direct replacement set of wires for your car from an auto parts store is going to make your life much easier. The wires will fit correctly, making for a smoother installation.

Instructions

    1

    Open the hood of your Camry and locate the negative battery terminal. Loosen the clamp bolt on the negative battery cable end with a wrench and remove it from the battery terminal. Isolate the battery cable from the battery for safety while you work.

    2

    Locate the spark plug wires on the spark plugs. The plugs are on the front of the engine about halfway down the cylinder head.

    3

    Grasp the spark plug wire boot on the spark plug end of the wire and pull it straight off the plug while twisting it side to side to help loosen it from the plug. Follow the wire along its length and locate the boot at the ignition coil.

    4

    Grasp the boot on the coil end of the spark plug wire and pull it out of the coil. If you are installing new wires, now is the time to replace this one. Move to the next wire and repeat the process, continuing one wire at a time until you replace or remove all four wires.

Read More.. >

Friday, January 24, 2014

Fuel Pump Replacement on a 2000 GMC Yukon

The GMC Yukon is a full-size SUV very similar to the Chevrolet Tahoe. The Yukon XL has a longer wheelbase than the base model, and the Yukon Denali is a luxury version of the Yukon. The most common engine in the 2000 GMC Yukon is an 8-cylinder 5.3-liter engine that uses sequential fuel injection. All versions of this vehicle have an electric fuel pump that supplies fuel to the fuel injection under high pressure.

Instructions

    1

    Disconnect the cable on the negative terminal of the battery with a socket wrench. Remove the filler cap on the fuel tank, and wrap a shop towel around the fuel pressure fitting on the inlet fuel pipe of the fuel injectors. Connect a fuel pressure gauge to the fuel pressure fitting. Place the hose for the fuel pressure gauge into a gasoline container, and open the valve on the gauge. Drain and disconnect the fuel tank. Disconnect the fuel pressure gauge from the inlet fuel pipe.

    2

    Remove the retaining ring for the fuel sender assembly with a fuel tank sending unit wrench. Disconnect the fuel sender assembly and discard the gasket. Hold the main body of the fuel sender assembly, and disconnect the fuel strainer from the fuel-sending assembly. Discard the fuel strainer.

    3

    Clean the surface of the fuel tank around the mounting area for the fuel-sending assembly. Disconnect the electrical connections to the fuel pump. Unfasten the retaining clip for the fuel level sensors electrical connector, and disconnect the fuel level sensors electrical connector. Loosen the retaining clip for the fuel level sensor and remove the fuel level sensor. Disconnect the fuel pressure sensor.

    4

    Attach the fuel pressure sensor, fuel level sensor and electrical connector for the fuel level sensor to the new fuel-sending assembly. Connect the electrical connector to the new fuel pump. Position the new fuel pump strainer to the new fuel-sending assembly so that it will be horizontal when you install the fuel-sending assembly to the fuel tank. Ensure that the fuel pump strainer does not block the movement of the fuel float arm. Push the strainer to seat it on the bottom of the fuel sender.

    5

    Install a new gasket for the fuel-sending assembly on the fuel tank. Connect the fuel-sending assembly to the fuel tank, and fasten the retaining ring with the fuel tank sending unit wrench. Connect the fuel tank, and use a torque wrench to tighten the bolts for the fuel tank strap to 30 foot pounds. Fill the fuel tank, and replace the filler cap for the fuel tank. Attach the cable for the negative terminal of the battery.

    6

    Turn the ignition on for 2 seconds and off for 10 seconds to pressurize the fuel system. Start the engine, and check for fuel leaks.

Read More.. >

Monday, January 20, 2014

How to Remove Brake Drums From a 2000 Honda Accord

Removing the brake drums from the rear of your Honda Civic allows access to the brake shoes, brake hardware and slave cylinders. The drums do not wear quickly, so replacing them is not normally a requirement. However, the drum can warp from excess heat. The shoes will require replacement and maintenance periodically. While the drums are off the car, it is a good idea to inspect the springs and hardware, as well as the slave cylinders and the brake lines.

Instructions

    1

    Loosen the lug nuts on the rear of your Civic with a lug wrench. Do not take the nuts off the studs yet. Raise the rear of the car with a jack, and position a set of jack stands under the rear suspension.

    2

    Lower the jack, allowing the car to rest on the jack stands. Remove the lug nuts from the wheel studs, and slide the tires and wheels off the car. Set them aside.

    3

    Pry the retaining clips off the wheel studs, if they are still in place, with a flat screwdriver. They look like flat washers on the wheel studs and against the face of the brake drum. Discard the clips.

    4

    Move to the back of the brake drum, and slide a flat screwdriver into the adjuster access hole on the brake drum backing plate. Lift the locking tab off the adjuster. Insert a brake spoon into the adjuster hole, and turn the brake adjuster up to loosen the brake shoe pressure against the drum.

    5

    Move to the front of the brake drum, and grasp it on the side. Pull it straight off the shoes and wheel studs. Set the drum aside, and repeat the process on the opposite brake drum to remove it, as well.

Read More.. >

Saturday, December 7, 2013

How to Take a Catalytic Converter Off a 2000 Grand Am SE 3400

The Pontiac Grand Am SE came standard with a 150-horsepower, 2.4-liter four-cylinder engine, but did have an optional 170-horsepower, 3.4-liter V-6 engine, which some people know as the 3400 V-6. The 2000 Grand Am SE used a muffler-like component, the catalytic converter, to convert the toxic gasses in the exhaust to less harmful ones. Replacing the cat on the 2000 Grand Am SE 3400 is a straightforward task, thanks to the vehicles simple exhaust design.

Instructions

Removal

    1

    Allow the vehicle to sit until the engine is cool to the touch, then allow it to sit for an additional hour to allow the exhaust and catalytic converter to cool completely.

    2

    Lift the front of the Grand Am with a floor jack and slide jack stands under its subframe. Lower the vehicle onto the jack stands.

    3

    Crawl under the center of the vehicle and find the catalytic converter-and-front pipe assembly. Position a pair of jack stands under the catalytic converter-and-front pipe assembly to support it.

    4

    Remove the three bolts securing the catalytic converter-and-front pipe assembly to the intermediate pipe -- the pipe to the rear of the catalytic converter -- using a ratchet and socket.

    5

    Unfasten the two bolts securing the catalytic converter-and-front pipe assembly to the exhaust manifold crossover pipe, which is the pipe connecting the front and rear exhaust manifolds, using a ratchet and socket. Slowly lower the catalytic converter-and-front pipe assembly and remove it from the vehicle.

    6

    Pull the old gaskets from the crossover and intermediate pipes, if needed, and scour the mating surfaces of both pipes with a wire brush.

Installation

    7

    Crawl under the vehicle with the catalytic converter-and-front pipe assembly in hand and set the assembly on the jack stands to hold it in place.

    8

    Line up the bolt holes in the catalytic converter-and-front pipe assemblys front-most flange with those in the crossover pipes flange. Slide a new gasket between the flanges, aligning the gaskets bolt holes with those in the flanges, and hand-tighten the two retaining bolts.

    9

    Align the bolt holes on the catalytic converter-and-front pipe assemblys rearmost flange with those on the intermediate pipes flange. Slide a new gasket between the flanges, aligning the bolt holes in the gasket with those in the flanges, and hand-tighten the bolts.

    10

    Tighten all five of the catalytic converter-and-front pipe assemblys retaining bolts to 25 foot-pounds using a torque wrench and socket.

    11

    Raise the Grand Am off the jack stands and remove the stands. Lower the vehicle to the ground.

Read More.. >

Wednesday, November 27, 2013

2000 Infiniti I30 Wont Start

2000 Infiniti I30 Wont Start

The Infinity I30 is a four-door sedan designed as a luxury car. If you are having problems starting your Infinity I30, you will need to check the battery. The battery is the most common reason that a car will not start. Corrosion can build up on the battery terminals and leave them inoperable. Cleaning the corrosion and then jump-starting the battery will tell you if you need to replace the battery all together.

Instructions

    1

    Open the hood to your I30 and locate the battery. The battery is next to the engine.

    2

    Disconnect the battery terminals from the battery. Clean the terminals with soda and a wire brush to clean the corrosion off.

    3

    Put the terminals back onto the battery and then start the I30.

    4

    Jump start your I30 with jumper cables. Allow the car to sit for about 5 minutes and then turn it off.

    5

    Restart the car. If the car will not restart, replace the battery.

    6

    Check the fuel level in the car. Add fuel and then start the car.

Read More.. >

Sunday, November 17, 2013

How to Fix a Bad Catalytic Converter on 2000 Toyota Tundra

How to Fix a Bad Catalytic Converter on 2000 Toyota Tundra

Fixing a catalytic converter is a complicated process because of the laws that govern virtually every aspect of installing, maintaining and replacing catalytic converters. The Environmental Protection Agency issued regulations in 1986 that make it illegal to tamper with your vehicles catalytic converter in any way, shape or form. Any repairs made to a vehicles catalytic converter have to be performed and properly documented by a certified mechanic.

Instructions

    1

    Take your Tundra to an emissions testing facility or exhaust repair shop and have your catalytic converter tested. You have to be able to document that your Tundras converter has stopped working before you are legally allowed to have it replaced.

    2

    Make sure that your Toyota is no longer covered by the federal emissions warranty. If your 2000 Toyota Tundra does not have 80,000 miles on it yet, then Toyota is required to replace the converter at no cost to you. If your Tundra is still under warranty, take it to your nearest Toyota dealership for repairs.

    3

    Take the Tundra to the dealership or exhaust repair shop (if it is not already there) and provide them with documentation that the converter is bad. Legally, they are only allowed to replace your converter with a catalytic converter that is the same as the one currently installed on your Toyota. Have the shop replace the catalytic converter. Make sure the shop fills out and submits the warranty card for the new converter, as it is legally required by federal law.

    4

    Save all documentation relating to the converter swap. If your Tundra has a problem with the catalytic converter or fails an emissions test in the future, you may need this information to get repairs performed and avoid possible fines.

Read More.. >

Wednesday, November 6, 2013

2000 Pontiac Bonneville Starting Problems

2000 Pontiac Bonneville Starting Problems

On February 16, 2004, General Motors informed the National Highway Traffic Safety Administration that it would be recalling certain 2000 Bonneville Pontiacs for an issue causing drivers to experience backfires if the engine was not starting when cranked. Owners of this model experiencing starting problems should contact NHTSA to determine whether their vehicles were affected by this recall.

Cause

    2000 Bonnevilles equipped with 3800 V6 L36 engines and certain Delphi Fuel pressure regulators may experience a high level of fuel leaks that can let fuel into the intake manifold. The manufacturer reports that if the engine doesnt start when cranked, the car may backfire from the regulator fuel leak.

Consequence

    If the Bonneville backfires, the intake manifold may rupture. A rupture could cause the fuel line and fuel injector to displace, leading to a fuel lead or fire that could cause injury or property damage.

Solution

    Take affected vehicles to authorized dealers to have a new fuel pressure regulator installed. Call NHTSA or the manufacturer with the VIN number of the vehicle to verify that it was recalled, if necessary, or to find out where to take the car for free repair.

Read More.. >

Friday, October 18, 2013

How Do I Replace a 2000 Hyundai Sonata GLS Oxygen Sensor

The oxygen sensors in the 2000 Hyundai Sonata GLS are threaded into the exhaust manifold and the exhaust pipe near the catalytic converter. When an oxygen sensor malfunctions, your car will burn a significant amount of additional fuel. To save the unnecessary fuel expense and possible long-term engine damage, you should replace the sensors as soon as possible. Buy sensors for your Sonata from an auto-parts store or Hyundai dealer.

Instructions

    1

    Raise the Sonata with a jack. Rest the car on jack stands for stability.

    2

    Locate the oxygen sensor either on the manifold or near the catalytic converter, depending on which one you need to change. Pull the wiring connection apart. Remove the oxygen sensor using a wrench.

    3

    Coat the threads of the sensor with anti-seize. Select an anti-seize compound designed for electrical components. Insert the new sensor by hand. Torque it to 40 foot-pounds with your torque wrench.

    4

    Push the two ends of the wiring harness together. The connector will click when it is attached. Repeat the replacement process on the second oxygen sensor if necessary. Lift the car slightly and pull the jack stands out of place. Lower the car to the ground.

Read More.. >

Saturday, October 12, 2013

How to Replace the Third Light on a 2000 Nissan Altima

Replacing the bulb in the high mount taillight on the rear of your 2000 Nissan Altima can help to prevent a rear end collision. It allows following drivers to notice your braking sooner. The high mount brake light contains two 921 bulbs and replacements are at any auto parts store, department store or the dealer. Changing the bulbs will only take a couple minutes and does not require tools.

Instructions

    1

    Climb into the back seat of your Altima and locate the third brake light housing on the rear package deck. Grasp the edges of the third brake light assembly and push it toward the rear of the car using light, even pressure. Do not push so hard that you break the glass.

    2

    Lift up on the housing, removing it from the rear deck. There are wires under the housing so do not pull it to far out or you will damage the wiring.

    3

    Turn the housing so you can access the bulbs and pull them straight out of the sockets. Install new 21 bulbs.

    4

    Position the light housing, pushing it slightly forward and down and slide it back. The housing will lock in place.

Read More.. >

Wednesday, October 9, 2013

How to Wire a Power Seat in a 2000 Infiniti I30

The Infiniti I30 was Nissans first serious entry into the luxury-car market. Hoping to emulate Toyotas success with the Lexus brand, Nissan up-contented their basic cars into luxury offerings. The I30 was essentially a re-badged Nissan Maxima with an upgraded interior and a more supple ride. Power seats were standard and allowed driver and passenger to change the position of their seats with the press of a button. However the motors in these seats can burn out and a replacement seats need to be wired into place.

Instructions

    1

    Drive the Infiniti I30 somewhere flat and with ample room to the drivers side. Car seats are bulkier than they look and having the flat ground helps keep the seat from sliding around on the rails. Put the Infiniti into "Park" and pull the emergency brake up before turning the car off. Pull the hood latch and go around to the front of the car. Open the trunk hood up and disconnect the black wire from the car battery.

    2

    Turn the power button to off on the underside of the power seat. Push the seat forward and unbolt the two rear retaining bolts on each rail. Move the seat to the rear and unbolt each bolt on the front of the rails. Pull them up and off, but not out of the car. Disconnect the power wire from the bottom of the seat, then take the seat out. Pull the runner assembly off the rails and disconnect the power wire from the gear box.

    3

    Pull the carpet flap off the bottom of the power seat and disconnect the wiring harness from each motor. Pull the carpet flap off of the new power seat and plug the wiring harness into the bottom of the seat. Slide the carpet flap back over so that only the single power port is left out at the rear.

    4

    Slide the runners at the bottom of the seat onto the rails. Bolt in the retaining bolts at the rear and then at the front of the seat. Plug the power cord coming from the floor into the port coming from the wiring harness. Reconnect the black wire to the car battery, shut the hood and turn the car back on. Test the Infinitis power seat by moving it forward, back, and angle it forward and to the rear.

Read More.. >