Showing posts with label catalytic. Show all posts
Showing posts with label catalytic. Show all posts

Sunday, April 27, 2014

How to Replace the Catalytic Converter on a 1993 Saturn SL2

The catalytic converter on your Saturn SL2 bolts to a flange on the rear of the head pipe coming off the engine. A clogged converter can cause the engine to run very rough and will build up excessive amounts of heat under your car, which can radiate into the passenger compartment through the floorboards. While many people shy away from exhaust work, you can change the converter at home in the driveway and save yourself a potentially large repair bill.

Instructions

    1

    Position a jack under the front of your SL2 and raise the front end off the ground so you can work underneath it. Place a set of jack stands under the front suspension then lower the jack, allowing the car to settle onto the jack stands.

    2

    Slide under the car near the back of the front wheels. The catalytic converter attaches to the head pipe near the rear of the engine with four bolts and a mounting flange. Loosen the nuts on the four bolts with a socket and ratchet, but do not remove them yet.

    3

    Locate the exhaust clamp on the pipe at the rear of the catalytic converter where it joins the rear exhaust pipe. Remove the two nuts from the clamp, then remove the clamp from the pipe. Move to the front of the converter and remove the four mounting bolts that you loosened earlier, then lower the front of the converter away from the head pipe.

    4

    Pull the converter forward, sliding it out of the rear pipe. Lower it to the ground and remove it from under the car.

    5

    Position a new converter under the car and raise it until you can slide the rear fitting on the converter into the rear pipe. Slide it in far enough to allow you to raise the front flange to the flange on the head pipe.

    6

    Install a new brass gasket between the front flanges, then install the four mounting bolts and nuts. Tighten the bolts with a socket and ratchet on one side and a wrench on the other. Install a new exhaust clamp on the rear pipe and tighten the nuts to secure it. Do not over-tighten it, or you will crush the exhaust pipe.

    7

    Move out from under the car and raise it off the jack stands with a jack. Remove the jack stands then set the car on its wheels. Remove the jack from under the car.

Read More.. >

Wednesday, March 19, 2014

Does the Catalytic Converter Affect Fuel Economy

Catalytic converters are part of a cars exhaust system that reduce the amount of nitrous oxide produced by burning fuel. When working properly the converter should not affect fuel economy, but it can if it becomes clogged or damaged.

Exhaust Backpressure

    If your cars catalytic converter becomes plugged or clogged, it restricts the airflow of exhaust from the engine. This causes more and more exhaust to build up in the engine which reduces the amount of new, combustible oxygen the engine pulls in. A common cause of a clogged catalytic converter is overheating due to a misfiring spark plug.

Diagnosis

    When it is receiving less oxygen, the engine must work harder to achieve speed. This increased work lowers fuel economy, reduces power when driving at high speeds and can cause overheating and stalling. If your car runs normally for a few minutes after starting, but then begins to cough or sputter, your converter may be clogged. Especially if you have noticed other symptoms, have your mechanic check the cars exhaust backpressure.

Solution

    If your catalytic converter is clogged or damaged, it will need to be replaced. Make sure to investigate the reason that the first converter was ruined so the replacement does not suffer the same fate.

Read More.. >

Wednesday, March 12, 2014

Why Does a Car Need Two Catalytic Converters

Why Does a Car Need Two Catalytic Converters?

Catalytic converters were first put into use in the 1970s in response to the growing pollution problem in cities throughout the U.S. Today, all road-legal cars must, by law, be equipped with a catalytic converter and some even have two.

Function

    Catalytic converters remove harmful elements from automotive exhaust by forcing the fumes to pass over metallic catalysts, including platinum, rhodium and palladium, which neutralize the toxins and transform them into relatively safe components. The entire casing of the converter is constructed of stainless steel. All of these expensive metals make a catalytic converter a costly piece of equipment.

Cars with Dual Exhaust

    While most production cars have only one catalytic converter, some do come with two. Cars with dual exhaust often have two catalytic converters --- one for each set of pipes running from the headers to the rear of the vehicle.

Cars with Two In-Line Catalytic Coverters

    Newer high-end vehicles are now coming equipped with two catalytic converters as part of an even more stringent emissions program. The first converter breaks down the exhaust as normal, while the second acts both as a filter for tiny particles and a pump which releases a chemical mixture that further reduces any harmful gases which may have escaped the first converter.

Read More.. >

Wednesday, February 26, 2014

How to Replace the Catalytic Converter In a 2001 Alero

How to Replace the Catalytic Converter In a 2001 Alero

Oldsmobile, in an attempt to tap into the younger market in the late 1990s, released the compact and somewhat sporty Alero, which the maker based on the same platform as the Pontiac Grand Am. The Alero ended up being the last Oldsmobile to ever roll off an assembly line, as Olds closed up shop in mid-2004. The 2001 Alero came standard with a 2.4-liter four-cylinder engine that produces a respectable 150 horsepower. The catalytic converter on the Alero is part of the front pipe, so replacing the catalytic converter requires replacing the entire catalytic converter-and-front pipe assembly.

Instructions

Removal

    1

    Park the Alero on a flat surface and allow it to sit until the engine is cool to the touch. Allow the vehicle to sit for an additional hour to allow the exhaust and catalytic converter to cool completely.

    2

    Lift the front of the Alero with a floor jack and slide jack stands under the vehicles subframe. Lower the vehicle onto the jack stands.

    3

    Crawl under the center of the Alero and find the catalytic converter-and-front pipe assembly, the long pipe that the catalytic converter is a part of.

    4

    Find the oxygen sensor screwed into the pipe just behind the catalytic converter. Trace the sensors wiring up to the engine compartment until you find the harness that connects it to the Aleros wiring harness. From inside the engine compartment, unplug the sensors harness from the vehicles harness.

    5

    Position yourself back under the vehicle and remove the oxygen sensor from the pipe, using a ratchet and oxygen sensor socket. If the oxygen sensor is seized, spray its base with penetrating oil and allow the oil to sit for the amount of time specified by the oil manufacturer, then remove the sensor.

    6

    Slide two jack stands under the catalytic converter-and-front pipe assembly to support it. Remove the bolts securing the intermediate pipe -- the pipe behind the catalytic converter -- to the catalytic converter-and-front pipe assembly, using a ratchet and socket.

    7

    Unfasten the bolts securing the front of the catalytic converter-and-front pipe assembly to the exhaust manifold, using a ratchet and socket. Lower the catalytic converter-and-front pipe assembly onto the jack stands.

    8

    Pull the catalytic converter-and-front pipe assembly out front under the vehicle. Remove the old gaskets from the exhaust manifold flange and intermediate pipe flange, if needed. Clean the mating surface on each flange with a wire brush.

Installation

    9

    Crawl back under the Alero, bringing the new catalytic converter-and-front pipe assembly along with you. Set the assembly on the jack stands in its mounting position.

    10

    Line up the bolt holes in the catalytic converter-and-front pipe assemblys flange with those in the exhaust manifolds flange. Slide a new gasket between the two flanges, aligning the bolt holes in the gasket with those in the flanges, then hand-thread the retaining bolts.

    11

    Align the catalytic converter-and-front pipe assembly rear flanges bolt holes with those on the intermediate pipes flange. Slide a new gasket between the flanges and align the bolt holes on the gasket with those in the flanges. Hand-tighten the retaining bolts.

    12

    Tighten the front catalytic converter-and-front pipe assembly bolts to 33 foot-pounds and the rear catalytic converter-and-front pipe assembly bolts to 25 foot-pounds, using a torque wrench and socket.

    13

    Apply a coat of anti-seize compound to the oxygen sensors threads and thread the sensor into the new catalytic converter-and-front pipe assembly. Torque the oxygen sensor to 30 foot-pounds, using a torque wrench and oxygen sensor socket.

    14

    Route the oxygen sensors wiring back toward the Aleros wiring harness in the engine compartment, then crawl out from under the vehicle. From inside the engine compartment, plug the oxygen sensors wiring harness to the Aleros harness.

    15

    Raise the vehicle off the jack stands and remove the stands. Lower the vehicle to the ground.

Read More.. >

Tuesday, February 4, 2014

How to Remove a Catalytic Converter on a 1995 GMC 1500

Removing the catalytic converter from your GMC 1500 series pickup for replacement or to facilitate other repairs is very simple. The converter is located in the downstream exhaust pipe just behind the exhaust manifolds. On models with dual exhaust, there are two converters, one in each exhaust pipe. Replacement converters are available at most auto parts stores and through the dealer if yours need replacing.

Instructions

    1

    Raise the front of your truck off the ground with a jack and support it by placing a set of jack stands under the frame rails. Lower the jack, setting the truck securely on the stands then remove the jack from under the truck.

    2

    Slide under the truck and locate the catalytic converter in the exhaust system just down from the engine. One sits in each pipe, so you will need to complete the process twice if you are removing both converters.

    3

    Remove the retaining bolts from the rear-mounting flange where the converter and exhaust pipe meet with a wrench. Lower the exhaust pipe away from the rear of the converter and lay it off to one side.

    4

    Move to the front of the converter and remove the bolts from the front mounting flange with a wrench. Separate the converter from the front pipe and lower it out from under the truck.

Read More.. >

Saturday, December 7, 2013

How to Take a Catalytic Converter Off a 2000 Grand Am SE 3400

The Pontiac Grand Am SE came standard with a 150-horsepower, 2.4-liter four-cylinder engine, but did have an optional 170-horsepower, 3.4-liter V-6 engine, which some people know as the 3400 V-6. The 2000 Grand Am SE used a muffler-like component, the catalytic converter, to convert the toxic gasses in the exhaust to less harmful ones. Replacing the cat on the 2000 Grand Am SE 3400 is a straightforward task, thanks to the vehicles simple exhaust design.

Instructions

Removal

    1

    Allow the vehicle to sit until the engine is cool to the touch, then allow it to sit for an additional hour to allow the exhaust and catalytic converter to cool completely.

    2

    Lift the front of the Grand Am with a floor jack and slide jack stands under its subframe. Lower the vehicle onto the jack stands.

    3

    Crawl under the center of the vehicle and find the catalytic converter-and-front pipe assembly. Position a pair of jack stands under the catalytic converter-and-front pipe assembly to support it.

    4

    Remove the three bolts securing the catalytic converter-and-front pipe assembly to the intermediate pipe -- the pipe to the rear of the catalytic converter -- using a ratchet and socket.

    5

    Unfasten the two bolts securing the catalytic converter-and-front pipe assembly to the exhaust manifold crossover pipe, which is the pipe connecting the front and rear exhaust manifolds, using a ratchet and socket. Slowly lower the catalytic converter-and-front pipe assembly and remove it from the vehicle.

    6

    Pull the old gaskets from the crossover and intermediate pipes, if needed, and scour the mating surfaces of both pipes with a wire brush.

Installation

    7

    Crawl under the vehicle with the catalytic converter-and-front pipe assembly in hand and set the assembly on the jack stands to hold it in place.

    8

    Line up the bolt holes in the catalytic converter-and-front pipe assemblys front-most flange with those in the crossover pipes flange. Slide a new gasket between the flanges, aligning the gaskets bolt holes with those in the flanges, and hand-tighten the two retaining bolts.

    9

    Align the bolt holes on the catalytic converter-and-front pipe assemblys rearmost flange with those on the intermediate pipes flange. Slide a new gasket between the flanges, aligning the bolt holes in the gasket with those in the flanges, and hand-tighten the bolts.

    10

    Tighten all five of the catalytic converter-and-front pipe assemblys retaining bolts to 25 foot-pounds using a torque wrench and socket.

    11

    Raise the Grand Am off the jack stands and remove the stands. Lower the vehicle to the ground.

Read More.. >

Tuesday, November 19, 2013

Catalytic Converter Components

Catalytic Converter Components

The catalytic converter in your auto exhaust system is a pollution control device designed to stop smog by turning unburned hydrocarbons and combustion byproducts of engines into normal atmospheric gases, said the PollutionIssues.com website. This device, which became mandatory in the 1980s, turns the carbon monoxide, nitric oxide and hydrocarbons of engine exhaust into carbon dioxide, nitrogen gas and water vapor. Catalytic converters have 3 main components: Catalysts, substrate and outer can.

Catalytic Elements

    In chemistry, a catalyst is a substance that triggers chemical reactions without itself being consumed by those reactions. Catalytic converters use platinum, rhodium and cerium as the catalysts that clean up exhaust gases. As exhaust gases pass through the converter, these materials get extremely hot, about 750 degrees Fahrenheit, and trigger oxidation reactions that break down passing exhaust gases into normal atmospheric gases.

Ceramic Substrate

    Inside the converter is a honeycomb-like ceramic substrate that has been coated inside and out with the catalytic elements. This structure provides a huge surface area for the oxidation reactions to occur, said PollutionIssues.com. Tetraethyl lead, once widely used as a gasoline octane booster, was removed from gasoline in the early 1980s because it would coat the substrate, blocking the catalytic reactions. In effect, lead poisoned the converter.

Outer Can

    The outer metal can holds the interior components in place. It typically is a steel cylinder with fittings to connect to the exhaust manifold at one end and the exhaust pipe at the other. The can is lined with an insulating mat to help hold in the heat that ensures efficient operation.

Read More.. >

Monday, November 18, 2013

How to Install a New Catalytic Converter for Ford Contours

This is not to say that a backyard mechanic couldnt successfully install a new catalytic converter laying on his back underneath a Ford Contour. Its not going to be fun or pretty. There are different designs in the Ford Contour and different motors. Each type will dictate where the catalytic converter is located and determine the degree of difficulty to remove and replace the old one. Some Contours have more than one converter so assuming which type your car is and what it needs will be up to you.

Instructions

    1

    Lift the Contour on a lift all the way to the top. Load all the tools and new converter into the tool tray and bring it over near you, but keep it out of the way. Put on the safety glasses and locate the converter and determine what youre going to need and where youre going to start.

    2

    Start with the front of the converter, closest to the motor. If it is attached to the manifold, set up the pneumatic gun, extension, swivel, and the correct sized socket before lighting the torch. Make sure the gun is set to reverse.

    3

    Light the torch and heat up the manifold stud nuts and when theyre cherry red, turn off the torch, put the gun and socket on the nut and remove it. Repeat this for all the remaining nuts. If the converter is flanged to a front pipe and not the manifold, light the torch and cut the nuts and bolts out of the flange to separate the connection.

    4

    Cut the rear bolts of the catalytic converter flange connection to the center exhaust pipe with the torch. Again, cutting the bolts from the converter side of the flange connection. Cut the bolts flush or inverted into the flange and turn the torch off. You will be able to knock the remaining bolt through the rest of the flange connection with a hammer and punch if its cut correctly.

    5

    Remove the old converter and install the new one. Again, start from the front of the Contour to connect the converter and work your way back. It might be wise to allow the exhaust components heated up by the torch to cool down before proceeding. If the converter attached to the manifold place it up onto the studs with the gasket in between and thread on the new manifold stud nuts hand tight. Then re-tighten with the pneumatic gun, swivel, and socket. If it flange connected to a front pipe, place the gasket between the flanges and replace the hardware.

    6

    Bolt and flat washer on one side of the flange connection and lockwasher and nut on the other side. Tighten the nuts to the bolts with the gun and socket on the nut end and hold the bolt head with a hand wrench.

    7

    Attach the rear flange connection of the catalytic converter to the center exhaust pipe flange and replace the hardware in the same manner and tighten. If the outlet of the converter is clamp connected to the center pipe, you may need to expand the center pipe (or converter depending on whether it fit over or into the pipe) with a pipe expander

    8

    Replace the clamp and tighten with the gun and a socket. Once the converter is connected and tightened on both ends, it may be wise to lower the vehicle on the lift, start it up, and raise it back up just to check for any possible leaks coming from the flange or clamp connections.

Read More.. >

Sunday, November 17, 2013

How to Fix a Bad Catalytic Converter on 2000 Toyota Tundra

How to Fix a Bad Catalytic Converter on 2000 Toyota Tundra

Fixing a catalytic converter is a complicated process because of the laws that govern virtually every aspect of installing, maintaining and replacing catalytic converters. The Environmental Protection Agency issued regulations in 1986 that make it illegal to tamper with your vehicles catalytic converter in any way, shape or form. Any repairs made to a vehicles catalytic converter have to be performed and properly documented by a certified mechanic.

Instructions

    1

    Take your Tundra to an emissions testing facility or exhaust repair shop and have your catalytic converter tested. You have to be able to document that your Tundras converter has stopped working before you are legally allowed to have it replaced.

    2

    Make sure that your Toyota is no longer covered by the federal emissions warranty. If your 2000 Toyota Tundra does not have 80,000 miles on it yet, then Toyota is required to replace the converter at no cost to you. If your Tundra is still under warranty, take it to your nearest Toyota dealership for repairs.

    3

    Take the Tundra to the dealership or exhaust repair shop (if it is not already there) and provide them with documentation that the converter is bad. Legally, they are only allowed to replace your converter with a catalytic converter that is the same as the one currently installed on your Toyota. Have the shop replace the catalytic converter. Make sure the shop fills out and submits the warranty card for the new converter, as it is legally required by federal law.

    4

    Save all documentation relating to the converter swap. If your Tundra has a problem with the catalytic converter or fails an emissions test in the future, you may need this information to get repairs performed and avoid possible fines.

Read More.. >

Saturday, November 9, 2013

How to Replace a Nissan Altima Catalytic Converter

How to Replace a Nissan Altima Catalytic Converter

The catalytic converter on your Nissan Altima cannot be repaired if it is defective. Replacement is the only option in these cases. Replacement catalytic converters are available from most auto parts stores but for the best fit, replacements from the dealer are a better option. The converter gets very hot when the car is running so be sure to allow the car to sit for about an hour before attempting this repair.

Instructions

    1

    Raise the front of your Maxima with a jack and a set of jack stands under the front suspension. Lower the jack, allowing the car to rest on the stands, and then remove the jack.

    2

    Crawl under the car. Locate the catalytic converter underneath the center of the car. Four bolts attach the heat shield to the bottom of the catalytic converter case. Remove the bolts with a socket and ratchet then removed the heat shield from the converter body.

    3

    Locate the flanges at each end of the catalytic converter and remove the bolts on both ends with a wrench. Pull the converter out from between the two exhaust pipe sections and discard it.

    4

    Lift a new converter into place and insert a new gasket between the exhaust flange and the converter flange on both ends. Install two mounting bolts on each end then tighten them with a socket and ratchet.

    5

    Install the heat shield using four mounting bolts and tighten them with a socket and ratchet. Raise the car off of the jack stands with your jack, and then remove the stands from under the car.

    6

    Lower the car to the ground and remove the jack from under the front on the car.

Read More.. >

Friday, November 8, 2013

How to Remove Catalytic Converter Nuts

Catalytic converters are usually flange-connected to exhaust systems, integrated with the front exhaust pipe or bolted directly to the manifold. Nuts and bolts still have to be removed, no matter what it is that separates the converter from the exhaust system. Because they are exposed to the high temperatures of the exhaust system as well as the open elements underneath the vehicle, it doesnt take long for the nuts and bolts to corrode and rust, fusing together. Removing catalytic converter nuts involves raising your vehicle and applying some heat before you even put a wrench to the nuts.

Instructions

    1

    Drive the vehicle up onto ramps or hoist it upward with the jack and support it onto jack stands. Apply the parking brake.

    2

    Put on the goggles and gloves and grab the tools before crawling under the vehicle.

    3

    Light the torch and avoid laying directly beneath the catalytic converter hardware. Place the tip of the flame from the torch to the nut only, avoiding applying heat to the bolt as much as possible. Move the flame tip around the circumference of the nut every 30 seconds and wait for the nut to become a bright, cherry red; then turn off the torch.

    4

    Place a wrench on the bolt head of the connection and the ratchet and a socket on the nut. Turn the nut counterclockwise. If the nut begins to bind up, reheat the nut with the torch.

    5

    Repeat this procedure for all the nuts (and bolts) being removed and replaced.

Read More.. >

Monday, October 21, 2013

DIY Catalytic Converter Replacement

DIY: Catalytic Converter Replacement

A catalytic converter in a car helps eliminate harmful exhaust emissions that contribute to air pollution. After many years of use, the converter can become clogged and cause the vehicle to run poorly. Usually, the car will have very little power and will not be able to achieve a speed above 20 miles per hour. These are the two main symptoms that a new catalytic converter may be needed.

Instructions

    1

    Locate the catalytic converter by tracking the exhaust pipe from the engine: the catalytic converter will be the first large rectangular-shaped object that you come across. It looks somewhat like the muffler, but it will always come first in the exhaust system before the muffler. Raise the front corner of the car on the side that the catalytic converter is nearest to with a jack. Slide a jack stand under the frame of the car and lower it onto the stand with the jack. Crawl under the vehicle and spray penetrating lubricant onto all of the bolts on the exhaust system near the catalytic converter.

    2

    Use a wrench to unscrew the oxygen sensor that connects to the exhaust system near the catalytic converter. This sensor will be a small piece sticking out about the size of a spark plug. There will be a wire attached to it. Allow the sensor to hang off to the side by this wire.

    3

    Loosen the bolts in the clamp between the catalytic converter and the engine with a wrench then remove the clamp. Move to the back of the converter and locate the bolts in the coupling in the exhaust pipe. Use the wrench to remove these bolts. The catalytic converter and the pipe attached to it will drop down slightly.

    4

    Work the assembly back and forth to pull the pipe apart where it was clamped in front of the converter. You will also be pulling out the pins attached to the exhaust pipe that go through the rubber bushings on the exhaust pipe hangers. When all of this comes loose, you will be able to pull the converter out from under the vehicle.

    5

    Slide the new converter under the vehicle. Lift it and slide the pipe on the front of it onto the exhaust coming from the engine. At the same time, push the pins into the bushings on the hangers. When the catalytic converter is properly positioned, the rear coupling should be ready for the bolts to be reinserted and tightened. Use the wrench and tighten these bolts.

    6

    Move the clamp back into position in front of the converter and tighten the bolts to fasten the pipes securely. Screw the oxygen sensor back into the port on the exhaust pipe and tighten it with the wrench. Start the car and check for leaks. Tighten the bolts if any leaking is present. Remove the jack stand and lower the jack to return the car to the ground.

Read More.. >

Thursday, October 3, 2013

Types of Catalytic Converters for Scrap

Catalytic converters can be worth their weight in gold. In fact, when the metal market crashes, only the rhodium, palladium, platinum and gold in these car parts is worth extracting. The outer steel casing is only worth throwing into a pile with other steels to be melted down and recycled.

Small Foreigns

    Small foreigns are appropriately named, as these converters come off of compact non-American-origin vehicles. These converters are usually small and lightweight and may lack a "honeycomb" pattern on the outside. Due to the steel grille on the inside part of the exhaust pipe on these converters, they must be busted in half to obtain the precious metals within. Some older small foreigns may have silver in them instead of gold and may lack rhodium entirely.

Large Foreigns

    Large foreigns are named as such because these converters come off of luxury-sized and larger non-American-origin vehicles. These converters may weigh up to 50 lb. each and are often bolted and welded to the underside of the vehicle, requiring a standard reciprocating saw and a sledgehammer to remove them. Large foreign catalytic converters have a steel grille on the inside of the exhaust pipe and must be broken apart to retrieve the metal within. Though gold is usually in short supply in most large foreign models, these are full of platinum and rhodium.

General Motors

    GM, or General Motors, catalytic converters come from vehicles that are made under the General Motors name, such as Chevrolet or GMC. These converters come from all sizes of vehicle made by this company. Because these converters lack a steel grille inside the exhaust pipe, inserting a thin, solid metal rod into one end of the exhaust pipe and pounding it against the metal inside will work to extract the precious metals. GM catalytic converters are often found to contain mostly platinum and palladium.

BMW

    BMW catalytic converters come from vehicles with the same name. These are not classified as large foreigns, despite their overseas origin, because of their structure. These catalytic converters are often made in a Y-shape, with three "honeycomb" areas in total to extract metal from. Though these models dont have a steel grille inside the exhaust pipes, its difficult to extract the precious metals from these catalytic converters without breaking them apart. Smashing them with a sledgehammer will often open one side enough so you can pry out the metal within.

Ford

    Ford catalytic converters are found in cars made by Ford, such as Ford or Mercury vehicles. These catalytic converters are often quite heavy and filled with mostly rhodium. Since these converters dont have a metal grille on the inside of the exhaust pipe, they may be extracted in the same manner as GM models.

Read More.. >

Monday, September 30, 2013

Do Saturns Have Catalytic Converters

Do Saturns Have Catalytic Converters?

A catalytic converter, or catalyst, is responsible for reducing the amount of pollutants that emit into the atmosphere while a vehicle is being driven. Saturn vehicles do have catalytic converters.

Types

    Some cars have an oxidation catalyst that reduces carbon monoxide and hydrocarbons, also known as a two-way catalyst. Some Saturn catalysts control the emission of nitrogen as well, known as three-way catalysts.

Emission Check

    Catalysts can become clogged and therefore must be serviced. Many auto shops can perform inspections to see if your Saturn has a plugged catalyst; there are also emission inspection facilities for diagnosis and/or repair.

Replacement

    Although catalysts dont often break from normal use of your car, replacing one is not such a detailed process. If you do it yourself, be sure to acquire the correct catalyst for your Saturn and new flange gaskets, nuts and bolts and anti-seize compound to coat them with.

Read More.. >

Monday, September 23, 2013

How to Replace a Catalytic Converter on a KIA Sedona

The Kia Sedona has a complex exhaust system comprising two manifold converters, a front dual-chambered exhaust pipe, the catalytic converter, two mufflers and a resonated tailpipe. If the catalytic converter gets clogged or breaks down internally, it can be replaced without having to replace any other components.

Instructions

    1

    Place the Sedona on a car lift and bring the vehicle all the way up on the lift.

    2

    Put on the cutting glasses and light the oxyacetylene torch. Cut the two bolts on the front converter flange with the torch. Cut the bolts flush to the flange on the converter side.

    3

    Cut the two bolts on the rear converter flange in the same manner.

    4

    Shut off the torch and switch the cutting glasses to safety glasses. Put on the safety gloves.

    5

    Knock out the remainder of the bolts on the front flange connection using the hammer and a long-stemmed punch. Knock out the remainder of the bolts on the rear converter flange. Allow the converter to cool down.

    6

    Remove the catalytic converter hangers from the rubber exhaust hangers and remove the converter.

    7

    Clean the flange connections of the front pipe and the front muffler that the converter attaches to using the angled die grinder and a coarse reconditioning disc.

    8

    Install the new converter and gaskets. Place the converter hanger into the rubber exhaust hangers first to hold it up, insert the gaskets between the flanges and place the bolts through the flange holes to support the converter. Use a flat washer against the bolt head on one side and the lock washer and nut on the other side.

    9

    Tighten the bolts and nuts with the impact gun, swivel and a socket while holding the bolt heads with a hand wrench.

    10

    Remove the debris below the Sedona and lower it down to the floor.

    11

    Start up the engine and relift the Sedona to check for exhaust leaks at the front or rear flange connections.

Read More.. >