Showing posts with label kia. Show all posts
Showing posts with label kia. Show all posts

Sunday, March 23, 2014

How to Replace the Timing Belt on a 2005 KIA Spectra

The Kia Spectra is a compact car produced from 2000 to 2009. The second generation of this series includes the 2004 through 2009 models, and represents a major redesign over the first generation Kia. The only engine available for the 2005 Kia in North American is a four-cylinder 2.0-liter engine with a double overhead camshaft. This design uses a timing belt to drive the camshafts with the crankshaft. The most important part of replacing the timing belt is keeping the crankshaft and camshafts in the correct position during the procedure.

Instructions

    1

    Disconnect the cable from the negative battery terminal with a socket wrench to ensure you dont inadvertently start the engine. Raise the vehicle and support it on jack stands. Remove the engine cover, right wheel and side cover for the right wheel. Detach the accessory drive belts, water pump pulley and upper cover for the timing belt.

    2

    Turn the crankshaft pulley clockwise to align the groove on the pulley with the timing mark on the lower timing belt cover. Disconnect the pulley and flange for the crankshaft with a socket wrench. Remove the lower timing belt cover and timing belt tensioner. Detach the timing belt from the pulleys.

    3

    Turn the crankshaft clockwise to align the timing marks for the crankshaft and camshaft. Install the timing belt tensioner with a socket wrench. Place the new timing belt onto the crankshaft sprocket, idler pulley, camshaft sprockets and timing belt tensioner in that order.

    4

    Turn the timing belt tensioner clockwise to apply tension to the timing belt. Press the tension side of the timing belt with moderate force. The tension is correct when the deflection of the timing belt is about 0.2 in. Tighten the mounting bolts for the tensioner to 20 ft. lbs. with a torque wrench. Turn the crankshaft clockwise by two full turns and align the timing marks once again.

    5

    Attach the lower timing belt cover and tighten its mounting bolts to between six and seven ft. lbs. with a torque wrench. Connect the flange and pulley for the crankshaft. Tighten the bolt for the crankshaft pulley to between 123 and 130 ft. lbs. Connect the upper timing belt cover and tighten the mounting bolts to between six and seven ft. lbs.

    6

    Install the water pump pulley and accessory drive belts with a socket wrench. Attach the right wheel and side cover for the right wheel. Replace the engine cover and connect the cable to the negative battery terminal with a socket wrench.

Read More.. >

Thursday, March 20, 2014

How to Install a Timing Belt on a 2002 KIA Rio Cinco

The Kia Rio is a subcompact car that Kia Motors has produced since 2001. The Cinco trim level of the Rio is a five-door hatchback available in the United States. The procedure for installing the timing belt depends only on the engine and is not directly affected by the trim level. The 2002 Kia Rio Cinco has a four-cylinder, 1.5-liter engine that uses a timing belt to synchronize the movements of the camshaft and crankshaft.

Instructions

    1

    Remove the cable from the negative terminal of the battery with a socket wrench. Detach the accessory drive belts from their respective pulleys. Disconnect the alternator and water pump.

    2

    Disconnect the crankshaft pulley with a socket wrench and remove the guide plate from the timing belt pulley. Disconnect the upper and lower covers for the timing belt.

    3

    Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing mark on the engine. The I and E marks on the camshaft pulley must also align with their respective marks on the cylinder head. Disconnect the timing belt tensioner pulley and the timing belt with a socket wrench.

    4

    Connect the pulley for the timing belt tensioner. Pull the tensioner away from the crankshaft pulley as far as possible and fasten the lock bolt for the tensioner to hold it in place. Place the timing belt onto the crankshaft pulley, idler pulley, exhaust camshaft pulley, intake camshaft pulley and tensioner pulley, in that order.

    5

    Loosen the pulley for the timing belt tensioner to apply tension to the timing belt. Tighten the lock bolt to between 28 and 38 foot-pounds with a torque wrench. Turn the crankshaft clockwise by two full turns and align the timing marks.

    6

    Install the upper and lower covers for the timing belt with a socket wrench. Tighten the mounting bolt for the crankshaft pulley to between 9 and 13 foot-pounds with a torque wrench. Connect the water pump pulley and tighten its mounting bolt to between 9 and 13 foot-pounds.

    7

    Install the alternator and attach the accessory drive belts. Connect the cable to the negative terminal of the battery.

Read More.. >

Friday, February 7, 2014

How to Replace a Passenger Mirror on a Kia

Kia uses plastic side view mirrors housed inside of a large shell on all of their late model vehicles. The method for replacement is generally the same for all models. The plastic shells have three threaded posts inserted into the side and those threaded posts extend through the door and attach via nuts. To replace the passenger mirror on your Kia, you have to locate and remove the nuts that secure the mirror to the door.

Instructions

    1

    Locate the mirror cover on the inside of the Kia door. Its located on the inside the door, directly across from the passenger mirror. To remove the cover, pull on it to release the plastic tabs that secure it to the door.

    2

    Locate the three nuts under the cover and remove them with a 10mm socket. To avoid dropping the mirror, hold it with one hand while you remove the nuts with the other. Be caul not to drop the nuts inside of the door. If you drop a nut, you must remove the door panel to retrieve it.

    3

    Pull the mirror out of the door. Slide the new mirror into the side of the door. The threaded posts can chip the paint. Take caution to prevent this.

    4

    Secure the mirror to the door with the original 10mm bolts. If the new mirror came with different bolts, use those bolts. They may have a different thread pattern or be a different size.

    5

    Place the cover back onto the Kia door and push it into place with your fingers. Sometimes you have to strike it with the palm of your hand to get it to snap into place.

Read More.. >

Wednesday, October 16, 2013

Specialty Tools for the Kia Sportage

Specialty Tools for the Kia Sportage

The Kia Sportage is a compact, "crossover" sport utility vehicle. Its a smaller-sized SUV that the Korean automaker designed for singles or small families, providing durability, power and European-styled comfort. Kia produced the 2011 Sportage in base, LX and EX trim models, all with a standard 176-horsepower, 2.4-liter, four-cylinder engine.

Cam Belt Tensioner Wrench

    Shley Tools manufactures a cam belt tensioner wrench for the 2008 Kia Sportage. The tool is item number UN 120 4500, and as of 2011 retails for $21.15 online from the Car Parts Discount company. The tool is designed for two-pin adjustment tensioners. The "cam belt" is another name for a vehicles timing belt. It controls the timing of an internal combustion engines valves.

Touch-up Pen

    Kia manufactures a touch-up paint pen specifically for the Kia Sportage. The pen is the size of a regular permanent marker. It is dual-tipped, and delivers a clear coat for correcting minor scratches and dings. Its listed for sale online under Sportage accessories.

Hi-scan Pro

    The Hi-scan Pro is a diagnostic tool that scans original equipment manufacturer (OEM) parts for the Kia Sportage. The tools main body has an LCD display, a PCMCIA software card slot, an impulse generator, a built-in multimeter and a two-channel oscilloscope. The diagnostic Hi-Scan Pro also scans Hyundai vehicles.

    The scanner was designed for compatibility with a host of electronic parts and electrical systems. The tool accomplishes DTC reading and explanation, DTC erasing, live time current data in digits and graphic modes. The scanner also handles manual data item grouping on the display, actuation testing, item graphic view, and has a current data recording function.

    The scanner is equipped with a sensor simulation mode, a system identification, ECU number, an adaption function, service reset and trouble-shooting functions, and ECU reprogramming.

Lishi Lock Pick Tools

    The Lishi company sells several lock tools for the Kia Sportage and other Kia automobiles through distributor Alibaba. Voraus in France manufactures the Kia lock-pick tool, part number LPT-20; a simple pick made of durable, high-quality steel. Voraus sells various replacement car keys, transponder chips, locksmith tools, key programmers and key cutting machines.

    Lishi also sells a decoder pick, locksmith tool and auto lock opener combination for the Sportage and other Kia automobiles. The tool, made in China, is model number 074001-17. They are invaluable to Kia service centers and owners, for opening accidentally locked car doors.

Read More.. >

Monday, September 23, 2013

How to Replace a Catalytic Converter on a KIA Sedona

The Kia Sedona has a complex exhaust system comprising two manifold converters, a front dual-chambered exhaust pipe, the catalytic converter, two mufflers and a resonated tailpipe. If the catalytic converter gets clogged or breaks down internally, it can be replaced without having to replace any other components.

Instructions

    1

    Place the Sedona on a car lift and bring the vehicle all the way up on the lift.

    2

    Put on the cutting glasses and light the oxyacetylene torch. Cut the two bolts on the front converter flange with the torch. Cut the bolts flush to the flange on the converter side.

    3

    Cut the two bolts on the rear converter flange in the same manner.

    4

    Shut off the torch and switch the cutting glasses to safety glasses. Put on the safety gloves.

    5

    Knock out the remainder of the bolts on the front flange connection using the hammer and a long-stemmed punch. Knock out the remainder of the bolts on the rear converter flange. Allow the converter to cool down.

    6

    Remove the catalytic converter hangers from the rubber exhaust hangers and remove the converter.

    7

    Clean the flange connections of the front pipe and the front muffler that the converter attaches to using the angled die grinder and a coarse reconditioning disc.

    8

    Install the new converter and gaskets. Place the converter hanger into the rubber exhaust hangers first to hold it up, insert the gaskets between the flanges and place the bolts through the flange holes to support the converter. Use a flat washer against the bolt head on one side and the lock washer and nut on the other side.

    9

    Tighten the bolts and nuts with the impact gun, swivel and a socket while holding the bolt heads with a hand wrench.

    10

    Remove the debris below the Sedona and lower it down to the floor.

    11

    Start up the engine and relift the Sedona to check for exhaust leaks at the front or rear flange connections.

Read More.. >