Showing posts with label mirror. Show all posts
Showing posts with label mirror. Show all posts

Thursday, April 17, 2014

How Do I Replace a 2003 Expedition Side View Mirror Assembly

How Do I Replace a 2003 Expedition Side View Mirror Assembly?

The 2003 Ford Expedition features both a left and right side view mirror. These mirrors are important for backing up the large SUV and for keeping a caul eye on traffic behind the vehicle. Because of its larger size, the Expedition is a hard vehicle to back up while looking out the back window, and it takes a certain amount of skill to be able to do so.

Instructions

    1

    Open the door on the Expedition with the mirror that needs to be replaced.

    2

    Lower the window all the way down then turn the ignition off and remove the key.

    3

    Remove the outer screw located on the rear side of the door panel with a flat head screwdriver.

    4

    Remove the two retaining bolts located at the bottom of the door panel with a 7 mm socket wrench.

    5

    Pry off the door handle cover with a pry tool.

    6

    Remove the window control module cover with the pry tool and disconnect the wire harness connections under the cover.

    7

    Pry off the panel under the door pull bar with the pry tool then remove the two screws under the panel. Use the T-27 Torx head screwdriver to remove the screws.

    8

    Pry around the bottom and side of the door panel with the pry tool. When the retaining snaps are all unseated, reach behind the door panel and disconnect any remaining wire harness connections. Remove the door panel.

    9

    Disconnect the side view mirror wire harness.

    10

    Remove the three retaining bolts located on the door frame opposite the side view mirror with an 11 mm socket wrench. Be caul not to allow the mirror to fall and scratch the door when removing the last retaining bolt.

    11

    Feed the wire harness out through the access hole of the door frame and remove the old mirror.

    12

    Install the new mirror by reversing Steps 9 through 11.

    13

    Reinstall the door panel by reversing Steps 3 through 8.

Read More.. >

Friday, February 28, 2014

How to Replace a Lumina Rearview Mirror

The Chevy Lumina rearview mirror is attached by a small metal button glued to the windshield and a small setscrew. Replacing the mirror becomes necessary when the silver lective paint starts to peel off the back of the glass. When this happens, it becomes difficult to see in the mirror, and it could cause your Lumina to fail a state inspection. Replacing the mirror requires an Allen wrench and very little auto-repair knowledge.

Instructions

    1

    Push the mirror upward on its base so the lective glass faces the roof of the Lumina. This makes it easier to get the Allen wrench into the setscrew on the base of the rear view mirror.

    2

    Remove the setscrew with a 9/16 Allen wrench by turning the wrench counterclockwise.

    3

    Slide the rearview mirror up to remove it from the metal button glued to the Luminas windshield. The metal button has a groove cut into each side of it that grips the base of the mirror to prevent it from falling to the floor.

    4

    Place the new rearview mirror onto the windshield, directly above the metal button. Slide the base of the mirror down onto the metal button until it seats in place.

    5

    Thread the setscrew into the base of the mirror with your fingers to avoid cross-threading it. Tighten the screw with the Allen wrench.

Read More.. >

Thursday, February 27, 2014

Installing a Side View Mirror Assembly

Installing a Side-View Mirror Assembly

The design of a newer mirror assembly allows for a moderate amount of impact before breaking. The assembly has springs that allow it to flex both forwards and backwards. If the impact is hard enough, the plastic assembly could crack. If this happens, pulling the old mirror off and replacing it with a new side-view mirror assembly is necessary.

Instructions

    1

    Remove the cover located inside the door, opposite the rear-view mirror. The cover does not have screws. Instead, it has a few plastic tabs that press into slots in the door. To remove the cover, pull it off with your fingers.

    2

    Locate the wiring harness behind the cover. Disconnect the mirror motor from the vehicle by lifting up on the locking tab in the center of the connector. With the lock lifted, pull the two ends of the connector apart.

    3

    Roll the window down so you can hold the mirror and remove the nuts that secure the mirror to the door at the same time.

    4

    Remove all but one of the nuts that secure the mirror to the door. The nuts are located behind the cover you removed. Usually, there are three nuts. Use a long-well socket and ratchet.

    5

    Hold the mirror against the door and remove the final nut. Do not let the mirror fall out of the door. You risk scratching the paint on the door with the threaded posts used to hold the mirror in place.

    6

    Pull the mirror out of the door. Again, be caul not to scratch the door.

    7

    Slide the new mirror on the door.

    8

    Hold the mirror and thread all of the nuts onto the threaded post with your fingers.

    9

    Tighten each bolt with the long-well socket and ratchet.

    10

    Reconnect the electrical harness by sliding the two connectors together and pushing the locking tab back into place.

    11

    Snap the cover back onto the inside of the door by pressing it in place with your hand

Read More.. >

Friday, February 7, 2014

How to Replace a Passenger Mirror on a Kia

Kia uses plastic side view mirrors housed inside of a large shell on all of their late model vehicles. The method for replacement is generally the same for all models. The plastic shells have three threaded posts inserted into the side and those threaded posts extend through the door and attach via nuts. To replace the passenger mirror on your Kia, you have to locate and remove the nuts that secure the mirror to the door.

Instructions

    1

    Locate the mirror cover on the inside of the Kia door. Its located on the inside the door, directly across from the passenger mirror. To remove the cover, pull on it to release the plastic tabs that secure it to the door.

    2

    Locate the three nuts under the cover and remove them with a 10mm socket. To avoid dropping the mirror, hold it with one hand while you remove the nuts with the other. Be caul not to drop the nuts inside of the door. If you drop a nut, you must remove the door panel to retrieve it.

    3

    Pull the mirror out of the door. Slide the new mirror into the side of the door. The threaded posts can chip the paint. Take caution to prevent this.

    4

    Secure the mirror to the door with the original 10mm bolts. If the new mirror came with different bolts, use those bolts. They may have a different thread pattern or be a different size.

    5

    Place the cover back onto the Kia door and push it into place with your fingers. Sometimes you have to strike it with the palm of your hand to get it to snap into place.

Read More.. >

Tuesday, January 21, 2014

How to Replace a Side Mirror on a 2008 Elantra

The side mirror on a Hyundai Elantra consists of a plastic shell bolted to the side of the door, a small motor bolted inside the shell and a mirror lens attached to the motor. Hyundai designed the mirror to withstand a moderate amount of impact. However, if struck hard enough, the mirror lens will shatter. A shattered mirror could cause you to fail a vehicle inspection or even get you a ticket in a traffic stop.

Instructions

    1

    Remove the glass shards from the shell of the mirror. The lens is made of plastic so you will not get cut by the shards. If any of the shards are attached to the mirror motor, pull out on them to pop them off the motor.

    2

    Suck any of the small shards of plastic out of the housing with a vacuum cleaner. Any small pieces of plastic left inside of the shell could jam between the new mirror lens and the plastic shell, preventing you from being able to adjust the mirror.

    3

    Place the replacement mirror lens in the shell. The tight tolerance of the shell forces the mirror to center in the hole.

    4

    Press on the mirror lens to push the mounting tabs on the back of the mirror lens around the mirror motor until you feel the mirror pop into place.

Read More.. >

DIY Power Mirror Repair for a Tahoe

DIY Power Mirror Repair for a Tahoe

The side power mirror on a Chevy Tahoe can get damaged in small and large accidents alike. The good news is that you do not need to simply live with a damaged side power mirror. Order a new power mirror from your local dealership or auto body shop. You may also need to order auto paint for the mirror that matches your Tahoe. The replacement mirror can then be installed in your Tahoe in just a few hours.

Instructions

    1

    Find the screws on the inside of the Tahoe door panel. Use a screwdriver to remove the screws from the door panel. Pop the door panel out of place and set aside.

    2

    Remove the mirror trim with a door panel remover tool. Unscrew the three screws that are located beneath the mirror trim with a screwdriver. Place the screws somewhere safe.

    3

    Disconnect the cables in the mirror and the door. The cables should come apart easily. Remove the mirror from the door.

    4

    Slip the wiring for the Tahoe replacement mirror through the hole in the door. Screw the mirror into place with the screws from the old mirror. Connect the cable of the new mirror to the cable in the door. The cables should fit together nicely.

    5

    Replace the door panel. Screw it into place with the panel screws and a screwdriver. Push the mirror trim cover panel back into place.

Read More.. >

Saturday, November 9, 2013

How to Replace an Outside Mirror on a 1994 Chevy

As with most late-model vehicles, the outside mirrors on a 1994 Chevy utilize three threaded posts attached to the mirror assembly to secure the mirror to the side of the door from the inside. This design allows the manufacturer to attach the mirrors quickly during the build process. If you need to replace the mirror, you can take advantage of the fact that the bolts are easy to access and quick to remove.

Instructions

    1

    Locate the triangular access panel located on the inside of the door. The panel is on the opposite side of the mirror assembly. To remove the panel, pull it out.

    2

    Remove the three mounting bolts behind the access panel with a socket. Hold the mirror in place, when removing the final bolt, to keep the mirror from falling off the door.

    3

    Place threaded studs onto the new mirror assembly through the holes in the door and secure the mirror by tightening the three mounting nuts with the socket.

    4

    Replace the triangular access panel onto the door and lock it into position by pushing on it.

Read More.. >

Monday, September 23, 2013

How to Paint a Replacement Mirror

How to Paint a Replacement Mirror

An accident can leave your vehicle without a functioning side mirror. It is simple to replace a side mirror, but whether you buy a new replacement mirror or a used one, the mirror probably will not match the paint color of your car. A few coats of paint can transform the replacement mirror and make it look as if it was the original.

Instructions

    1

    Locate the factory paint color code for your car. This is the key to getting the best color match for your replacement mirror. Check the records for your car or contact your local dealer to find the code. Buy the paint and primer from an auto parts store.

    2

    Lightly sand the plastic on the replacement side mirror with fine-grit sandpaper. Wipe away the sanding dust from the mirror with a damp cloth.

    3

    Tape off any areas of the replacement mirror you do not want painted, using painters tape. Set the replacement mirror on a drop cloth in a well-ventilated area.

    4

    Spray the mirror with aerosol automotive primer. Apply the primer in two light coats. Let each coat dry before handling or applying paint or primer.

    5

    Spray the mirror with aerosol automotive paint. Again, apply the paint in light coats. Apply three coats of the paint, letting each coat dry before applying the next. Give the mirror 24 hours to dry before handling it. Remove the painters tape.

Read More.. >