Tuesday, January 21, 2014
How to Replace a Side Mirror on a 2008 Elantra
The side mirror on a Hyundai Elantra consists of a plastic shell bolted to the side of the door, a small motor bolted inside the shell and a mirror lens attached to the motor. Hyundai designed the mirror to withstand a moderate amount of impact. However, if struck hard enough, the mirror lens will shatter. A shattered mirror could cause you to fail a vehicle inspection or even get you a ticket in a traffic stop.
Instructions
- 1
Remove the glass shards from the shell of the mirror. The lens is made of plastic so you will not get cut by the shards. If any of the shards are attached to the mirror motor, pull out on them to pop them off the motor.
2Suck any of the small shards of plastic out of the housing with a vacuum cleaner. Any small pieces of plastic left inside of the shell could jam between the new mirror lens and the plastic shell, preventing you from being able to adjust the mirror.
3Place the replacement mirror lens in the shell. The tight tolerance of the shell forces the mirror to center in the hole.
4Press on the mirror lens to push the mounting tabs on the back of the mirror lens around the mirror motor until you feel the mirror pop into place.
Wednesday, October 30, 2013
2008 Impala Alignment Specs
The current generation of the Chevy Impala was introduced in 2006. It is a full-sized family sedan available in several trims. A 50th Anniversary edition was available for the 2008 model year, and there were four different types of suspension used on the Impala in 2008. Check your owners manual to determine which type of suspension your car has, and always check your owners manual or consult a certified mechanic before attempting to make any auto repairs.
Alignment Specs for the Soft Ride Suspension System
For the front end, the caster angle can range from +2.40 degrees to +3.40 degrees, with the ideal setting being +2.90 degrees. The camber angle can range from -1.30 degrees to -.30 degrees, with the ideal setting being -.80 degrees. The toe-in can range from -.10 degrees to +.30 degrees. The steering-wheel angle can range from -3.50 degrees to +3.50 degrees, but ideally it should be evened out at zero degrees.
For the rear end, the camber angle can range from -1.15 degrees to -.15 degrees, with the ideal being -.65 degrees. The total toe can range from -.10 degrees to +.30 degrees, with the ideal setting being +.10 degrees. The thrust angle can range from -.15 degrees to +.15 degrees. The caster angle is not adjustable on the rear end.
Alignment Specs for the Sport Suspension System
For the front end, the caster angle can range from +2.65 degrees to +3.65 degrees, with the ideal setting being +3.15. The camber angle can range from -1.20 degrees to -.20 degrees, with the ideal setting being -.70 degrees. The toe-in can range from -.10 to +.30 degrees. The steering-wheel angle can range from -3.50 degrees to +3.50 degrees, but ideally it should be evened out at zero degrees.
For the rear end, the camber angle can range from -1.40 degrees to -.40 degrees, with the ideal setting being -.90. The total toe can range from -.10 degrees to +.30 degrees, with the ideal setting being +.10 degrees. The thrust angle can range from -.15 degrees to +.15 degrees. The caster angle is not adjustable on the rear end.
Alignment Specs for the SEO Vehicle Police Car and the SEO Vehicle Police Car LC
For the front end of cars with the SEO Vehicle Police Car suspension system, the caster angle can range from +2.70 degrees to +3.70 degrees, with the ideal setting being +3.20 degrees. The camber angle can range from -1.00 degrees to zero degrees, with the ideal setting being -.50 degrees. The toe-in can range from -.10 degrees to +.30 degrees. The steering angle can range from -3.50 degrees to +3.50 degrees, but ideally it should be evened out at zero degrees.
For the front end of cars with the SEO Vehicle Police Car LC suspension system, the caster angle can range from +2.55 degrees to +3.55 degrees, with the ideal setting being +3.05. The camber angle can range from -1.15 degrees to -.15 degrees, with the ideal setting being -.65 degrees. The toe-in can range from -10 degrees to +.30 degrees. The steering angle can range from -3.50 degrees to +3.50 degrees, but ideally it should be evened out at zero degrees.
The rear-end alignment specs are the same for the SEO Vehicle Police Car and the SEO Vehicle Police Car LC. The camber angle can range from -1.20 degrees to -.20 degrees, with the ideal setting being -.70 degrees. The total toe can range from -.10 degrees to +.30 degrees, with the ideal setting being +.10 degrees. The thrust angle can range from -.15 degrees to +.15 degrees. The caster angle is not adjustable on the rear end.
Monday, September 16, 2013
How to Install a 2008 Altima Exhaust Tip
The factory exhaust tips on a 2008 Nissan Altima are located on the exit pipes of the muffler. These factory-fitted tips arent welded in place, nor are they secured with clamps like most aftermarket exhaust tips; they are lightly pressed into place and held on by pressure. Some Altima owners have even reported these tips coming loose and falling off on their own after time, although this is relatively uncommon. The automotive aftermarket provides a vast array of exhaust tips options, available from a number of performance parts websites, mail order catalogs, and automotive parts stores.
Instructions
- 1
Turn off the Altimas engine and allow the exhaust to cool for one to two hours; working on the exhaust too soon could cause serious burns.
2Raise the rear of the vehicle with a jack and lower it down onto jack stands. Check to make sure that the car is stable before moving on to the next step.
3Slide underneath the rear of the car on a mechanics creeper with a slip-joint pliers and a hammer. Grip the exhaust tip with a large, slip-joint pliers on the bare, uncoated portion of the tip just in front of the muffler. Wiggle the tip back and forth while pulling it away from the muffler until its free. If the tip is extra stubborn, tap it with a hammer while wiggling it with the pliers; the shock from the hammer blow will often dislodge it from its initial position and break some of the corrosion so you can remove it easier. Remove the second exhaust tip off of the muffler in the same manner.
4Position the new exhaust tip on the muffler. For factory-style exhaust tips, drive the tip into position with the same block of wood and hammer until its fully-seated, then reinstall the second exhaust tip using the same technique. For aftermarket exhaust tips, set them into position and then gently drive the tips into place with the block of wood and hammer. Tighten the set screws or exhaust clamps with a ratchet and metric socket.
5Check the tips to make sure that they are securely fastened to the muffler. Stand back from the vehicle to make sure that the exhaust tips are even. If the tips are slightly uneven or crooked, make small adjustments by tapping them with the block of wood and hammer, and then re-checking the exhaust clamps or set screws for tightness, if equipped.