Showing posts with label view. Show all posts
Showing posts with label view. Show all posts

Thursday, April 17, 2014

How Do I Replace a 2003 Expedition Side View Mirror Assembly

How Do I Replace a 2003 Expedition Side View Mirror Assembly?

The 2003 Ford Expedition features both a left and right side view mirror. These mirrors are important for backing up the large SUV and for keeping a caul eye on traffic behind the vehicle. Because of its larger size, the Expedition is a hard vehicle to back up while looking out the back window, and it takes a certain amount of skill to be able to do so.

Instructions

    1

    Open the door on the Expedition with the mirror that needs to be replaced.

    2

    Lower the window all the way down then turn the ignition off and remove the key.

    3

    Remove the outer screw located on the rear side of the door panel with a flat head screwdriver.

    4

    Remove the two retaining bolts located at the bottom of the door panel with a 7 mm socket wrench.

    5

    Pry off the door handle cover with a pry tool.

    6

    Remove the window control module cover with the pry tool and disconnect the wire harness connections under the cover.

    7

    Pry off the panel under the door pull bar with the pry tool then remove the two screws under the panel. Use the T-27 Torx head screwdriver to remove the screws.

    8

    Pry around the bottom and side of the door panel with the pry tool. When the retaining snaps are all unseated, reach behind the door panel and disconnect any remaining wire harness connections. Remove the door panel.

    9

    Disconnect the side view mirror wire harness.

    10

    Remove the three retaining bolts located on the door frame opposite the side view mirror with an 11 mm socket wrench. Be caul not to allow the mirror to fall and scratch the door when removing the last retaining bolt.

    11

    Feed the wire harness out through the access hole of the door frame and remove the old mirror.

    12

    Install the new mirror by reversing Steps 9 through 11.

    13

    Reinstall the door panel by reversing Steps 3 through 8.

Read More.. >

Thursday, February 27, 2014

Installing a Side View Mirror Assembly

Installing a Side-View Mirror Assembly

The design of a newer mirror assembly allows for a moderate amount of impact before breaking. The assembly has springs that allow it to flex both forwards and backwards. If the impact is hard enough, the plastic assembly could crack. If this happens, pulling the old mirror off and replacing it with a new side-view mirror assembly is necessary.

Instructions

    1

    Remove the cover located inside the door, opposite the rear-view mirror. The cover does not have screws. Instead, it has a few plastic tabs that press into slots in the door. To remove the cover, pull it off with your fingers.

    2

    Locate the wiring harness behind the cover. Disconnect the mirror motor from the vehicle by lifting up on the locking tab in the center of the connector. With the lock lifted, pull the two ends of the connector apart.

    3

    Roll the window down so you can hold the mirror and remove the nuts that secure the mirror to the door at the same time.

    4

    Remove all but one of the nuts that secure the mirror to the door. The nuts are located behind the cover you removed. Usually, there are three nuts. Use a long-well socket and ratchet.

    5

    Hold the mirror against the door and remove the final nut. Do not let the mirror fall out of the door. You risk scratching the paint on the door with the threaded posts used to hold the mirror in place.

    6

    Pull the mirror out of the door. Again, be caul not to scratch the door.

    7

    Slide the new mirror on the door.

    8

    Hold the mirror and thread all of the nuts onto the threaded post with your fingers.

    9

    Tighten each bolt with the long-well socket and ratchet.

    10

    Reconnect the electrical harness by sliding the two connectors together and pushing the locking tab back into place.

    11

    Snap the cover back onto the inside of the door by pressing it in place with your hand

Read More.. >