Showing posts with label 2003. Show all posts
Showing posts with label 2003. Show all posts

Friday, May 16, 2014

How to Replace the Timing Belt on a 2003 Ford Focus

Ford started production of the Ford Focus in 1999. The models made from 1999 to 2007 were the first generation of this series. The standard engine in the 2003 Focus has four cylinders and a displacement of 2.0 liters. The timing belt on this vehicle synchronizes the movements between the crankshaft and the camshaft. The tension on the timing belt is a critical factor in its installation.

Instructions

    1

    Open the hood. Disconnect the negative battery terminal with socket wrench. Turn the drive belt tensioner clockwise to reduce the tension on the accessory drive belt. Remove the drive belt. Disconnect the tensioner with a socket wrench. Remove the timing belt cover.

    2

    Raise and support the vehicle on jack stands. Remove the right front wheel with a lug wrench and disconnect the right splash shield. Remove the pulley for the crankshaft.

    3

    Turn the crankshaft clockwise to align the timing marks on the crankshaft and camshaft sprockets. Loosen the tensioner bolt on the timing belt with a socket wrench. Turn the tensioner counterclockwise by 1/4 turn with an 8mm Allen wrench. Place a 1/8-inch drill bit into the hole on the timing belt tensioner to hold the belt tensioner in place. Remove the timing belt.

    4

    Install the new timing belt onto the crankshaft by proceeding in a counterclockwise direction. Remove the drill bit from the hole in the timing belt tensioner. Turn the crankshaft clockwise by two turns so that the timing marks align once again. Torque the tensioner bolt for the timing belt to between 15 and 22 foot-pounds with a torque wrench.

    5

    Install the crankshaft pulley with a socket wrench and tighten its mounting bolt to between 81 and 96 foot-pounds. Connect the right splash shield and the right front wheel. Lower the vehicle and replace the timing belt cover. Install the accessory drive belt tensioner and mount the drive belt. Attach the cable to the negative battery terminal.

Read More.. >

Sunday, April 20, 2014

How to Replace a Diesel Injection Pump in a 2003 Dodge

A diesel engine is an option for many Dodge vehicles, especially heavy trucks. An eight-cylinder 5.9-liter diesel engine is available for the 2003 Dodge Ram 2500 3/4 ton pickup. This engine uses fuel injection and requires an injection pump to keep the fuel under pressure. The procedure for replacing the diesel injection pump is the same for all full-size Dodge trucks made from 2001 to 2005.

Instructions

    1

    Disconnect the cables from the negative battery terminals with a socket wrench. Remove the throttle linkage and its bracket. Disconnect the fuel drain manifold, and detach the fuel lines from the injection pump. Remove the fuel air control tube and the connector for the fuel shut-off valve from the injection pump. Disconnect the support bracket and oil fill tube from the injector pump.

    2

    Put a shop rag over the opening in the injector pumps gear cover. Remove the gear retaining nut and washer for the injector pump with a socket wrench. Turn the crankshaft clockwise with a socket wrench until the top dead center pin on the crankshaft drops into the gear timing hole. Pull the pin from the gear timing hole.

    3

    Remove the lock screw and its washer from the injection pump with a socket wrench. Tighten the lock screw to 22 ft. lbs. with a torque wrench, then push the drive gear for the injection pump from the drive shaft. Disconnect the mounting nuts for the injection pump with a socket wrench. Remove the injection pump from the crankcase.

    4

    Install the new injection pump and tighten the mounting nuts by hand, ensuring that the pump can move freely within its slots. Connect the drive gear to the drive shaft with its retaining nut and washer. Tighten the nut to between 11 and 15 ft. lbs. with a torque wrench.

    5

    Rotate the injection pump counterclockwise to take up gear lash. Tighten its mounting nuts to 18 ft. lbs. with a torque wrench. Connect the support bracket for the injection pump. Tighten the nut for the pump drive gear to 48 ft. lbs.

    6

    Connect the oil filler tube and connector valve for the fuel shut-off valve to the injector pump. Attach the fuel lines to the injector pump. Install the fuel drain manifold and throttle linkage with a socket wrench. Connect the cables for the negative battery terminals.

    7

    Loosen the bleed bolt on the fuel rail with a socket wrench. Push the primer button on the fuel transfer pump until the fuel coming from the bleed screw no longer has air bubbles. Tighten the bleed screw to 72 in. lbs. with a torque wrench. Start the engine and check for fuel leaks.

Read More.. >

Thursday, April 17, 2014

How Do I Replace a 2003 Expedition Side View Mirror Assembly

How Do I Replace a 2003 Expedition Side View Mirror Assembly?

The 2003 Ford Expedition features both a left and right side view mirror. These mirrors are important for backing up the large SUV and for keeping a caul eye on traffic behind the vehicle. Because of its larger size, the Expedition is a hard vehicle to back up while looking out the back window, and it takes a certain amount of skill to be able to do so.

Instructions

    1

    Open the door on the Expedition with the mirror that needs to be replaced.

    2

    Lower the window all the way down then turn the ignition off and remove the key.

    3

    Remove the outer screw located on the rear side of the door panel with a flat head screwdriver.

    4

    Remove the two retaining bolts located at the bottom of the door panel with a 7 mm socket wrench.

    5

    Pry off the door handle cover with a pry tool.

    6

    Remove the window control module cover with the pry tool and disconnect the wire harness connections under the cover.

    7

    Pry off the panel under the door pull bar with the pry tool then remove the two screws under the panel. Use the T-27 Torx head screwdriver to remove the screws.

    8

    Pry around the bottom and side of the door panel with the pry tool. When the retaining snaps are all unseated, reach behind the door panel and disconnect any remaining wire harness connections. Remove the door panel.

    9

    Disconnect the side view mirror wire harness.

    10

    Remove the three retaining bolts located on the door frame opposite the side view mirror with an 11 mm socket wrench. Be caul not to allow the mirror to fall and scratch the door when removing the last retaining bolt.

    11

    Feed the wire harness out through the access hole of the door frame and remove the old mirror.

    12

    Install the new mirror by reversing Steps 9 through 11.

    13

    Reinstall the door panel by reversing Steps 3 through 8.

Read More.. >

Sunday, February 9, 2014

How to Remove the Overhead Console on a 2003 Dodge Ram

Removal of the overhead console in your Dodge Ram will allow access to the electronics and light assemblies mounted in it. The console comes out without much effort and its removal does not require any special tools. There are several wiring connections under the console to disconnect before removal of the console, but they are readily accessible once the mounting hardware is removed. If your vehicles console is damaged, replacements are available from the dealerships parts department.

Instructions

    1

    Disconnect the negative battery cable from the battery by removing the retaining bolt on the cable end with a wrench, then isolate the cable end from the battery. Move inside the truck and open the sunglasses storage bin.

    2

    Locate the screws inside the storage bin and remove them with a Phillips head screwdriver. Set the screws aside for later use.

    3

    Grasp the sides of the console with your hands, then pull straight down on it until the two clips under the console release. The console may come off suddenly, so beware that you are not directly under it.

    4

    Slide your hand in under the console and disconnect the EVIC, CMTC and lamp connections from the back of the console. Lower the console and remove it from the truck.

Read More.. >

Wednesday, February 5, 2014

How to Change a 2003 Duramax Injector

A Duramax engine is an eight-cylinder diesel engine that General Motors has manufactured since 2001. It appears in heavy Chevrolet trucks, such as the Silverado 2500HD. The most common 2003 Duramax engine has a displacement of 6.6 liters with electronic fuel injection. The fuel injectors are on top of the engine and deliver fuel to the engine in the correct quantity and sequence. Each cylinder of the engine has its own fuel injector.

Instructions

    1

    Remove the cables from the negative terminals of both batteries with a socket wrench. This ensures that you dont inadvertently start the engine. Disconnect the lower valve cover. Detach the fuel line from the fuel injectors and remove the bracket from the fuel injector.

    2

    Connect Special Tool J-29873 to the retainer bracket of the fuel injector. Attach a socket wrench to the special tool and pry the retainer bracket away from the fuel injector.

    3

    Detach the fuel injector from the injection socket. Remove the copper washer from the injection socket if it is not attached to the injector. Apply assembly grease to the copper washer and place it back into the injection socket.

    4

    Install the new fuel injector into the injection socket. Install the injector bracket and tighten its retainer bolt to 36 ft. pounds. with a torque wrench.

    5

    Attach the fuel line to the fuel injector and tighten its retaining bolts to 108 in. lbs. with a torque wrench. Install the lower valve cover with a socket wrench. Connect the cables to the negative terminals of the batteries.

Read More.. >

Monday, December 9, 2013

How to Repair the Headlights on a 2003 Infiniti FX35

Infiniti equipped the 2003 FX35 models with a xenon bulb headlamp system. Over time, the bulb can fail because of vibration or shock caused by driving over rough road surfaces. The bulb and bulb socket snap into the back of the headlamp housing, allowing you replace the bulb without removing the entire headlamp assembly. Remove some engine compartment components to gain access to the headlamp housings.

Instructions

Passenger Side Headlamp Replacement

    1

    Turn the headlight control switch and the ignition switch to the Off position. Open the hood.

    2

    Locate the radiator overflow reservoir on the passenger side fender inside the engine compartment. Remove the overflow tube clamp from the radiator pressure cap tower, using pliers. Remove the reservoir mounting bolt, using a ratchet and socket. Pull the reservoir out of the engine compartment and place it in an upright position with the loose end of the overflow hose above the fluid level in the reservoir to prevent coolant loss.

    3

    Locate the headlamp socket on the rear of the headlamp housing. Rotate the headlamp cap counterclockwise to disengage it from the housing. Unsnap the socket retaining spring. Rotate the bulb socket assembly counterclockwise to disengage it from the housing and pull the bulb socket out of the housing.

    4

    Pull the old bulb out of the bulb socket. Insert the new bulb into position in the bulb socket. Insert the bulb socket in the housing and rotate it clockwise until it locks in the housing. Snap the socket retaining spring into position. Install the headlamp cap and rotate it clockwise until it locks in position.

    5

    Place the coolant overflow reservoir in position in the engine compartment. Install the reservoir mounting bolt and tighten it to 37 inch-pounds, using an inch-pound torque wrench and socket. Push the overflow tube onto the radiator pressure cap tower nipple and install the clamp, using pliers.

Driver Side Headlamp Replacement

    6

    Turn the headlight control switch and the ignition switch to the Off position. Open the hood.

    7

    Unsnap the four air cleaner case clips around the perimeter of the air cleaner case cover. Push the cover toward the driver side fender to disengage the cover from the air inlet duct, then lift the cover up and out of the engine compartment to gain access to the headlamp housing.

    8

    Locate the headlamp socket on the rear of the headlamp housing. Rotate the headlamp cap counterclockwise to disengage it from the housing. Unsnap the socket retaining spring. Rotate the bulb socket assembly counterclockwise to disengage it from the housing and pull the bulb socket out of the housing.

    9

    Pull the old bulb out of the bulb socket. Snap the new bulb in position in the bulb socket. Insert the bulb socket in the housing and rotate it clockwise until it locks in the housing. Snap the socket retaining spring into position. Install the headlamp cap and rotate it clockwise until it locks in position.

    10

    Place the air cleaner cover in the engine compartment. Cock the cover to the right and push it down until the grommet goes into the locator hole while guiding it onto the resonator below the cover. Push the cover to the left while guiding the air inlet duct into the hole in the side of the cover. Snap the four cover clips into position on the cover.

Read More.. >

Monday, December 2, 2013

How to Locate the EGR Valve on a 2003 Dodge Intrepid

How to Locate the EGR Valve on a 2003 Dodge Intrepid

The EGR or exhaust gas recirculation valve is part of the 2003 Dodge Intrepid emissions system. The EGR valve helps to reduce the levels of nitrogen oxides (NOX) in the vehicles exhaust. As your 2003 Dodge Intrepid ages, carbon deposits will eventually begin to build up on the valve and in the passages inside the intake manifold that lead to it. These carbon deposits will eventually decrease the efficiency of the engine, and could lead to the check-engine light illuminating.

Instructions

    1

    Locate the air-filter housing and duct. It will be on the right side of the engine bay.

    2

    Locate the throttle body. It will be positioned between the air duct and the engine.

    3

    Locate the bracket directly underneath the throttle body.

    4

    Locate the EGR valve. It will be bolted to the engine just to the right of the bracket and beneath the throttle body.

Read More.. >

Saturday, November 2, 2013

How to Install an Antenna on a Lexus 2003 Rx300

How to Install an Antenna on a Lexus 2003 Rx300

The Lexus Rx300 is a luxury SUV with a raising antenna. Even minor repairs to the RX300 can cost hundreds of dollars at a repair shop. If you would like to repair the RX300s antenna yourself, you can buy a replacement antenna from online auction websites or an auto parts store. You dont have to be a Lexus mechanic to repair your Rx300s antenna. You can do it yourself.

Instructions

    1

    Go to the antennas base and remove the nut at the bottom of the base with a wrench.

    2

    Get a friend to turn the car on, and then turn the radio on. This will force the antenna to raise. Pull on the antenna as it is raising to release it from the car.

    3

    Make sure that the retaining sleeve is at the bottom of the antenna after you have removed it. If it is not, use a pair of pliers to remove the retaining sleeve from the base.

    4

    Have your friend turn the car off. Line the new antenna up with the teeth facing the appropriate place in the antennas base. Lock the antenna in place.

    5

    Turn the radio back on to test the antenna. If the antenna does not raise fully, wiggle the base until the antenna is properly in place.

Read More.. >

Wednesday, October 23, 2013

How to Replace a 2003 Hyundai Sonata Timing Belt

The 2003 Hyundai Sonata is available with a four-cylinder 2.0-liter engine with a double overhead cam. This engine design requires a timing belt to synchronize the crankshaft with the camshaft. The Sonatas timing belt should be replaced approximately every 60,000 miles.

Instructions

    1

    Remove components as required to access the cover of the timing belt on the front of the engine. Disconnect the cover with a socket wrench. Turn the crankshaft clockwise to align the timing mark on the crankshaft sprocket with the timing mark on the cylinder head. This places the No. 1 piston in the top dead center position needed to replace the timing belt.

    2

    Disconnect the tensioner and the idler pulley for the timing belt with a socket wrench. Detach the timing belt from the crankshaft and camshaft.

    3

    Turn the crankshaft clockwise again to align the timing marks if necessary. Connect the tensioner for the timing belt and the idler pulley. Tighten the mounting bolt for the idler pulley to between 32 and 41 ft-lbs. with a torque wrench.

    4

    Place the timing belt over the camshaft sprocket and crankshaft sprocket in that order. Turn the timing belt tensioner to place tension on the timing belt. The timing belt is at the proper tension when five pounds of force in the middle of the longest span of the timing belt produces a deflection of 0.16 to 0.24 in.

    5

    Tighten the bolt for the tensioner pulley to between 32 and 41 ft-lbs. with a torque wrench. Turn the crankshaft sprocket clockwise by one complete turn to realign the timing marks.

    6

    Adjust the belt tension again if necessary. Replace the cover of the timing belt cover and any components you removed to access the timing belt.

Read More.. >

Tuesday, October 1, 2013

How to Replace the Shocks on a 2003 Dodge RAM

How to Replace the Shocks on a 2003 Dodge RAM

Shock absorbers should be replaced every 75,000 miles. Your 2003 Dodge ram has four shocks, one at each corner. The shocks that came with your truck from the factory are known to have problems. Your local mechanic may be able to do the installation for you, but you can do it yourself to save money.

Instructions

Front Shock Replacement

    1

    Open the hood by pulling the release lever inside the cab.

    2

    Spray each bolt that secures the shocks in place with penetrating fluid

    3

    Remove the nuts that hold the shock tower in place from inside the engine compartment using a ratchet and a 12mm socket.

    4

    Remove the bolt that secures the top of the shock to the shock tower using a ratchet and socket.

    5

    Remove the 3/4-inch nut that secures the shock to the axle using a ratchet and socket. Remove the shock from the brackets.

    6

    Install the replacement shock and tighten the lower bolt with a ratchet and socket.

    7

    Place the shock tower onto the top of shock and tighten the nut with a ratchet and socket.

    8

    Reinstall the shock tower and tighten the 12mm nuts with a ratchet and socket.

    9

    Repeat on the opposite side of the vehicle.

Rear Shock Replacement

    10

    Remove the 3/4-inch bolts that secure the rear shocks to the axle and the frame with a ratchet and socket.

    11

    Remove the shock from the brackets.

    12

    Install the new shock into the brackets and thread the stock bolts through the mounting holes. Install the nuts and tighten them using a ratchet and socket.

    13

    Repeat to the opposite side of the vehicle.

Read More.. >

Friday, September 20, 2013

How to Troubleshoot a 2003 Ford Escape

The 2003 Ford Escape is a small sports utility vehicle that features a V6 engine, large cargo capacity and manual transmission. The vehicle is considered a combination between an SUV and a mid-size car. As an Escape owner, you may experience problems intermittently with the vehicle. You can troubleshoot some of the most common problems without being a certified mechanic. In fact, basic troubleshooting of your Ford Escape may save you the expense of consulting an automobile repair specialist.

Instructions

Oil Pressure Indicator Light

    1

    Turn off your 2003 Ford Escape and raise the hood.

    2

    Locate and remove the oil dipstick near the engine. The dipstick will be labeled "Oil."

    3

    Wipe the dipstick clean with a paper towel or rag. Reinsert the dipstick in its hole.

    4

    Remove the dipstick again and check for the oil level.

    5

    Add more oil with a funnel if the oil level does not reach at least halfway to the fill line on the dipstick. Replace the dipstick and lower the hood.

Fuses

    6

    Locate the fuse box on the dashboard of the Ford Escape.

    7

    Remove the cover of the fuse box and review the diagram on the inside cover.

    8

    Locate the position of the electrical part that is not working. For example, if your radio is not working, the fuse for it is located in slot 12.

    9

    Remove the fuse with your index finger and thumb or pliers. If the metal link inside the fuse is separated or broken, the fuse is blown.

    10

    Insert a new fuse in the slot and replace the fuse box cover.

Overheating

    11

    Turn off your Ford Escape and allow the vehicle to cool.

    12

    Raise the hood and locate the coolant reservoir. The reservoir is located on the left side of the Escape.

    13

    Wipe the area around the reservoir cap. Remove the cap slowly.

    14

    Compare the amount of coolant in the reservoir to the fill line on the side.

    15

    Add more coolant and replace the reservoir cap.

Read More.. >