Showing posts with label duramax. Show all posts
Showing posts with label duramax. Show all posts

Wednesday, February 5, 2014

How to Change a 2003 Duramax Injector

A Duramax engine is an eight-cylinder diesel engine that General Motors has manufactured since 2001. It appears in heavy Chevrolet trucks, such as the Silverado 2500HD. The most common 2003 Duramax engine has a displacement of 6.6 liters with electronic fuel injection. The fuel injectors are on top of the engine and deliver fuel to the engine in the correct quantity and sequence. Each cylinder of the engine has its own fuel injector.

Instructions

    1

    Remove the cables from the negative terminals of both batteries with a socket wrench. This ensures that you dont inadvertently start the engine. Disconnect the lower valve cover. Detach the fuel line from the fuel injectors and remove the bracket from the fuel injector.

    2

    Connect Special Tool J-29873 to the retainer bracket of the fuel injector. Attach a socket wrench to the special tool and pry the retainer bracket away from the fuel injector.

    3

    Detach the fuel injector from the injection socket. Remove the copper washer from the injection socket if it is not attached to the injector. Apply assembly grease to the copper washer and place it back into the injection socket.

    4

    Install the new fuel injector into the injection socket. Install the injector bracket and tighten its retainer bolt to 36 ft. pounds. with a torque wrench.

    5

    Attach the fuel line to the fuel injector and tighten its retaining bolts to 108 in. lbs. with a torque wrench. Install the lower valve cover with a socket wrench. Connect the cables to the negative terminals of the batteries.

Read More.. >

Thursday, December 26, 2013

How to Remove 2004 Duramax Injectors

The Duramax family of diesel engines are designed by Isuzu and built by General Motors. They are primarily available in medium-duty trucks, such as the Chevrolet Silverado 2500 pickup. The first generation of Duramax engines had the engine code LB7, and were in production from 2001 through 2004. The 2004 Duramax engine used common-rail direct injection, which does not rely on an electronic controller. The procedure for removing the fuel injectors from a LB7 Duramax engine is generally the same for all vehicles.

Instructions

    1

    Disconnect the cable from the batterys negative terminal with a socket wrench to prevent the accidental discharge of fuel during the injector removal. Remove the mounting bolts for the lower valve cover and disconnect the cover.

    2

    Remove the retaining bolts for the fuel spill line with a socket wrench, and detach the spill line from the fuel injector. Remove the retainer bolt from the bracket of the fuel injector.

    3

    Attach fuel injector removal tool J 44639 to the bracket for the fuel injector. Grip the handle of the removal tool with a flare nut wrench.

    4

    Pull the flare nut wrench away from the fuel injector to pry it out of the injector hole. Remove the fuel injector from the vehicle.

    5

    Check the fuel injector for a copper washer. Remove the washer from the injection hole if the washer is not on the injector.

    6

    Repeat Steps Two through Five to remove the remaining fuel injectors.

Read More.. >

Sunday, October 6, 2013

How to Hook Up the Brake Controller on the 2006 Duramax

Duramax is the name of an 8-cylinder 6.6-liter diesel engine that General Motors has manufactured since 2001. The 2006 version carries the LLY designation and is an option for many full-size Chevrolet pickup trucks. The braking system on vehicles with a 2006 Duramax engine includes an electronic brake control module. The function of the EBCM is to keep the wheels from locking during an emergency stop by applying less braking force to a wheel that is rotating more slowly than the other wheels.

Instructions

    1

    Remove the negative battery cable with a socket wrench to prevent anyone from inadvertently starting the engine. Raise the vehicle with a floor jack and support it on jack stands. Clean the area around the EBCM under the vehicle with a shop cloth to prevent contamination of the disassembled braking components.

    2

    Disconnect the mounting screws for the EBCM with a socket wrench and discard the mounting screws. Pull the EBCM down slightly to detach it from the brake pressure modulator valve, or BPMV. Discard the EBCM.

    3

    Clean the mounting surfaces on the BPMV with a clean shop cloth to ensure a good electrical contact between the EBCM and BPMV. Install the new EBCM to the BPMV with new mounting screws and fasten the mounting screws with a socket wrench.

    4

    Lower the vehicle with the floor jack. Attach the negative battery cable with a socket wrench.

    5

    Turn the ignition on. Connect a scan tool to the data link connector under the dashboard on the left side of the steering column. Check and clear any error codes that the scan tool displays.

Read More.. >

Sunday, September 22, 2013

How do I Rebuild a Duramax Injector

The Duramax engines are a series of diesel engines that General Motors has manufactured for its larger trucks since 2001. Several different versions of these engines exist, but they all have a displacement of 6.6 liters. Duramax engines use direct fuel injection, which does not require an electronic controller. The procedure for rebuilding the fuel injector is generally the same as for all vehicles with a Duramax engine.

Instructions

    1

    Open your hood. Disconnect the cables from the negative terminals of the batteries with a socket wrench. Detach the clips on the fuel lines to the fuel injectors, and disconnect the fuel lines from the injectors. Remove the fuel return lines from the fuel injectors. Plug the open fuel lines with plastic caps to prevent debris from entering the fuel lines.

    2

    Attach GM special tool J-29873 to a socket wrench, and use this assembly to turn the fuel injector counterclockwise. Make sure you grip the 30 mm hex portion of the fuel injector to avoid damage to the injector. Remove the fuel injector, and cover its ends with plastic caps.

    3

    Replace the gasket on the fuel injector with a new gasket. Install the new fuel injector to the fuel rail. Fasten the fuel injector into place by turning it clockwise with GM special tool J-29873 and a socket wrench.

    4

    Attach GM special tool J-29873 to a torque wrench, and torque the fuel injector to 50 foot-pounds. Remove the protective caps from the fuel lines, and connect the fuel lines to the fuel injector. Fasten the retaining nuts for the fuel lines, and tighten them to 20 foot-pounds with a torque wrench.

    5

    Connect the fuel return line to the fuel injector, and attach the clips to the fuel lines. Connect the cables to the negative terminals of the batteries with a socket wrench.

Read More.. >