Showing posts with label brake. Show all posts
Showing posts with label brake. Show all posts

Wednesday, August 27, 2014

Jeep Cherokee Parking Brake Lever Removal

The brake lever sits in the center console of the Jeep Cherokee. The emergency brake cable runs under the Jeep and attaches from the bottom side, joining the two rear cables with the single front cable. While failure of the lever assembly is not common, the ratcheting gears inside the handle and the locking mechanism can fail. Those parts cannot be serviced individually. You have to replace the entire assembly to fix a problem with the lever or the components inside it.

Instructions

    1

    Raise the front of your Cherokee off the ground with a jack. Position a set of jack stands under the frame to support the Jeep. Slide under the Jeep and locate the parking brake equalizer, which is directly under the parking brake lever.

    2

    Remove the nut from the tension rod with a wrench. Slide the equalizer off the tension rod. Remove the front cable from the tension rod and lay it aside. Slide out from under the Jeep. Open the passengers door so you can access the center console and the brake lever.

    3

    Open the center console. Locate the two screws at the top edge of the trim panel that extends from the top of the console to the front of the brake lever cutout. Remove the screws with a Phillips screwdriver.

    4

    Pull the brake handle up then lift the rear of the trim panel up several inches. Slide the trim panel back to release it from the front of the center console and lift it off the brake lever.

    5

    Locate the electrical connector on the brake lever switch near the bottom of the brake handle assemble. It is on the drivers side near the back of the assembly. Pull the connector off the switch and set the connector aside.

    6

    Remove the two retaining bolts from the brake handle assembly with a socket and ratchet. Lift the assembly out of the console and remove it from the Jeep.

Read More.. >

Tuesday, April 29, 2014

How to Reset the Brake Light on a BMW 528i

How to Reset the Brake Light on a BMW 528i

The On-Board Diagnostics computer, or OBD, on your BMW 528i stores trouble codes that come from sensors positioned throughout the vehicle. These sensors keep track of the mechanical functions of your vehicle. When you see the ABS or Antilock Brake light flash on your instrument panel, you know there is a malfunction with your braking system. This needs to be looked at and repaired as soon as possible by a qualified mechanic. Once the repairs have been made, you need to reset the brake light to ensure the vehicles computer will continue to properly monitor the braking system.

Instructions

    1

    Locate the fuse panel cover on the drivers side dashboard, near the foot well. Use your fingers to pull down on it from the top.

    2

    Find a large port on the fuse panel. Plug the connective end of the OBD reset tool into this port.

    3

    Put the key into the ignition and turn it to the "on" position. Dont turn on the engine, though. This will power on the OBD reset tool automatically.

    4

    Wait for the codes to flash on the OBD reset tool screen. Use the arrow keys on the reset tool to find and select "Delete" on the menu screen. Some OBD reset tools have a "Delete" button on the face of the tool. Either way, select "Delete" and wait for the ABS light to blink and then turn off on the instrument panel.

    5

    Unplug the tool from the port and replace the fuse panel cover. Turn off the vehicle and wait 60 seconds. Turn the engine on and verify the ABS light is off.

Read More.. >

Wednesday, March 26, 2014

How to Adjust a Rear Brake Pedal on a Harley Road Glide

How to Adjust a Rear Brake Pedal on a Harley Road Glide

The original equipment connection between the rear brake pedal and the rear brake master cylinder on all Harley-Davidson Road Glides to date is completely mechanical and not hydraulic. The mechanical connection is the same whether your Road Glide is equipped with your original brake pedal or an aftermarket pedal.

Instructions

    1

    Sit down next to the right side of your motorcycle and find the brake pedal.

    2

    Find the rear brake master cylinder which is approximately parallel to the bottom of the brake pedal and about two feet closer to the rear of the bike. Then find the metal rod that connects the two.

    3

    Loosen the jam nut that connects the rear brake cylinder to the brake rod by turning the nut counterclockwise with an open end wrench.

    4

    Turn the brake rod with an open end wrench fitted to the flattened section of the brake rod. Turn the rod clockwise to lower the pedal and counterclockwise to raise the pedal.

    5

    Tighten the jam nut by turning it clockwise when the brake pedal is adjusted to the proper height.

    6

    Inspect the cotter pin that locks the brake rod to the brake pedal assembly. Use pliers to replace the cotter pin if it is broken or very corroded.

Read More.. >

Wednesday, March 12, 2014

How to Adjust a Parking Brake in a 95 Mx 5

How to Adjust a Parking Brake in a 95 Mx-5

You can adjust the parking brake on your 1995 Mazda MX-5 right from your home garage, saving time and money. You will know that its time to adjust your parking brake when the vehicle starts to slip when parked downhill. Adjusting the parking brake takes up the slack in the parking brake cable, allowing the parking brake to be more effective. You only need a few basic tools to do the job.

Instructions

    1

    Start the engine. Step on the brake pedal so it goes all the way to the floor four times. Shut off the engine.

    2

    Locate the center console cover between the drivers and passengers seats. Unhinge the hooks. Remove the cover by lifting up.

    3

    Find the adjuster nut attached to the parking brake cable. Tighten the nut with the wrench.

    4

    Lift up on the hand brake one click. Start the engine and look on the instrument panel to see that the parking brake light is on. Disengage the hand brake.

    5

    Put wheel chocks behind and in front of the front wheels. Lift up the rear end of the Mazda with a jack. Slide jack stands under the vehicle next to the two rear wheels. Lower the vehicle onto the stands.

    6

    Spin the rear wheels forward with your hands. If youve done the adjustment correctly, they should spin freely.

    7

    Raise up the vehicle, slide the jack stands out of the way and lower the car to the ground. Remove the jack and wheel chocks.

Read More.. >

Thursday, February 6, 2014

How to Install a Brake Controller in an 03 Dodge Ram

A Dodge Ram is a full-size pickup truck that Chrysler has manufactured under its Dodge brand since 1981. The 2003 model belongs to the third generation of this series, which was in production from 2002 to 2008. The anti-lock braking system in a 2003 Dodge Ram has a brake controller known as a hydraulic control unit, or HCU. The HCU prevents the wheels from locking during an emergency stop by reducing the braking power to a wheel when it rotates more slowly than the other wheels.

Instructions

    1

    Disconnect the housing for the left front turn signal with a socket wrench and remove the extension panel under the housing. Detach the electrical connector for the horn and disconnect the horns access cover.

    2

    Disconnect the mounting screws for the windshield washer reservoir and pull the reservoir up. Detach the electrical connector and hose from the windshield washer pump. Disconnect the reservoir and remove it from the engine compartment.

    3

    Remove the cables from the battery with a socket wrench and disconnect the power distribution center in the engine compartment. Push the connectors for the electrical wiring harness together to detach it from the controller anti-lock brakes. Disconnect the brake lines from the HCU.

    4

    Disconnect the front mounting bolt for the HCU bracket through the access opening with a socket wrench. Disconnect the rear mounting bolt for the HCU bracket from the engine compartment. Pull the HCU assembly up slightly and detach it from its bracket.

    5

    Place the new HCU in its mounting bracket, and install the HCU assembly. Tighten the mounting bolts for the HCU bracket to 11 foot-pounds with a torque wrench. Connect the brake lines to the HCU and tighten its retaining nuts 115 inch-pounds. Attach the wiring harness for the controller anti-lock brakes and lock the connectors into place.

    6

    Install the reservoir for the windshield washer. Connect the motor and hose for the windshield washer pump. Fasten the mounting screws for the reservoir with a socket wrench.

    7

    Attach the battery cables and the power distribution center. Connect the electrical connector for the horn, and replace the horns access cover. Fasten the extension panel and housing for the left front turn signal.

Read More.. >

Thursday, January 23, 2014

Rear Disc Brake Tools

Rear Disc Brake Tools

The rear disc brake on an automobile requires the use of a variety of specialty tools, when repairing or replacing it. Many of these tools are available at most auto parts stores, but some need to be ordered, or purchased, through an automotive tool supplier.

Disc Brake Piston Tool

    The disc brake piston tool is used to adjust the rear disc brakes on automobiles. This disc brake piston tool is used with a wrench and driver set. The piston tool looks like a cylinder, which fits around the piston and has a square hole, located in the middle of the cylinder, where the driver fits in place.

Rear Brake Caliper Kit

    Rear brake caliper kits are used on rear disc brakes, where the pistons are tied to the parking brake. When the pistons and parking brake are tied together, it requires the parking brake to be turned and pushed back, in order to gain access to the rest of the brake systems. It comes with different size adapters, in order to fit most domestic and import automobiles.

Disc Brake Caliper Spreader

    The disc brake caliper spreader is a tool used when the parking brake is not tied into the pistons. The caliper spreader is used to open the calipers, which hold, and press, the brake pads against the brake rotor. In order for the brake pads to be removed, the brake calipers need to be opened wide, or pressed open, with the caliper spreader. The disc brake caliper spreader looks like a small flat plate, with a rod and handle, which turns or screws, so the calipers can be pressed open.

Electronic Brake Fluid Tester

    The electronic brake fluid tester is used to check the moisture in the brake fluid. The brake fluid tester looks like a test tube that has LED lights, which inform the mechanic of the quality of the brake fluid. A little moisture in the brake fluid is acceptable, but this brake fluid tester has different colored lights, which tell how much moisture is in the brake fluid, so the mechanic can make a decision on whether to flush the rear brake lines and replace the fluid.

Brake Shoe Retaining Spring Tool

    The brake shoe retaining spring tool is a tool used on the rear disc brakes, to install or remove the retaining spring on the brake shoes. It comes with different size ends, which fit four different size springs. The brake-shoe retaining spring tool has a handle, located in the middle, so the mechanic can turn the tool.

Read More.. >

Wednesday, January 22, 2014

Replacing Brake Lightbulbs on an Isuzu Rodeo

The brake lights on your Isuzu Rodeo notify other drivers when you are stopping, making a safer driving experience for everyone. In fact, working brake lights are required by law. If your brake lights are out, you create a hazard for other drivers who may not notice you are stopping or slowing down. Replace your brake lights as soon as they go out. Replacement bulbs are available at any major auto parts store.

Instructions

    1

    Use a Phillips screwdriver to remove the two screws on the sides of the taillight assembly.

    2

    Remove the Phillips screw from underneath the taillight assembly.

    3

    Pull the assembly toward you and out of the back end of the Rodeo.

    4

    Turn the top light socket counterclockwise to unlock it from the assembly. Slide it out of the taillight assembly. The top socket is the brake light, while the other two are the turn signal lights and reverse lights.

    5

    Press the bulb in toward the socket and turn it counterclockwise to disengage it from the socket. Pull the bulb out of the socket. Slide a new bulb into the socket, press it down and turn it clockwise to lock it into the socket.

    6

    Slide the socket back into the taillight assembly and turn it clockwise to lock it in. Slide the assembly back into the rear of the Rodeo and replace the screws.

Read More.. >

Monday, January 20, 2014

How to Remove Brake Drums From a 2000 Honda Accord

Removing the brake drums from the rear of your Honda Civic allows access to the brake shoes, brake hardware and slave cylinders. The drums do not wear quickly, so replacing them is not normally a requirement. However, the drum can warp from excess heat. The shoes will require replacement and maintenance periodically. While the drums are off the car, it is a good idea to inspect the springs and hardware, as well as the slave cylinders and the brake lines.

Instructions

    1

    Loosen the lug nuts on the rear of your Civic with a lug wrench. Do not take the nuts off the studs yet. Raise the rear of the car with a jack, and position a set of jack stands under the rear suspension.

    2

    Lower the jack, allowing the car to rest on the jack stands. Remove the lug nuts from the wheel studs, and slide the tires and wheels off the car. Set them aside.

    3

    Pry the retaining clips off the wheel studs, if they are still in place, with a flat screwdriver. They look like flat washers on the wheel studs and against the face of the brake drum. Discard the clips.

    4

    Move to the back of the brake drum, and slide a flat screwdriver into the adjuster access hole on the brake drum backing plate. Lift the locking tab off the adjuster. Insert a brake spoon into the adjuster hole, and turn the brake adjuster up to loosen the brake shoe pressure against the drum.

    5

    Move to the front of the brake drum, and grasp it on the side. Pull it straight off the shoes and wheel studs. Set the drum aside, and repeat the process on the opposite brake drum to remove it, as well.

Read More.. >

Wednesday, January 15, 2014

How to Adjust Emergency Brake Cables on a 1997 F150

How to Adjust Emergency Brake Cables on a 1997 F150

You can adjust the emergency brake cables on your 1997 Ford F-150 yourself right from your home garage or driveway. This will save you a trip to the mechanic. When you park your F-150 on a downhill slope and the parking brake starts to slip, you know its time to adjust the cables on the parking brake. You just need a couple of tools purchased from your local auto parts retailer to get the job done. Start by parking the vehicle on level ground before making the adjustment.

Instructions

    1

    Step on the parking brake pedal, pressing it all the way to the floor.

    2

    Place wheel chocks in front of the front wheels and chocks behind the front wheels.

    3

    Put the floor jack under the back end of the vehicle and lift it up high enough to slid the jack stands underneath the F150 next to each wheel. Lower the vehicle onto the jack stands.

    4

    Get under the Ford and find the parking brake cable rod in the center of the vehicle. It is the rod with the cables coming to it. Hold the rod in place with your hand. Using pliers, tighten the equalizer nut about six turns.

    5

    Attach the cable tension gauge to the rear tension cable to measure and set the number of pounds of tension. Set the F-150s tension at 350 pounds.

    6

    Disengage the parking brake and spin the rear wheels to make sure they turn freely.

    7

    Adjust the parking brake equalizer nut so that it has a clearance of 0.38 mm if you find there is resistance when you spin the wheels.

    8

    Raise up the truck, remove the jack stands, lower the vehicle to the ground and remove the wheel chocks.

Read More.. >

Thursday, October 31, 2013

Brake Cylinder Honing Tools

Brake Cylinder Honing Tools

Wheel cylinders hold and control the brake fluid and control pressure in a rear (sometimes front) drum brake housing. They sit at the top of the backing plate between the brake shoes. Leaking wheel cylinders can result in a spongy brake pedal, and sometimes no brake pedal at all if the brake fluid drains out. All brake cylinders can be rebuilt, using replacement kits, a few tools and some acquired knowledge.

Variable Speed Drill

    One of the most versatile brake honing tools has been around for a long time, but the do-it-yourself vehicle owner may not have noticed its connection with brake repair. The electric hand-held drill plays an important role in honing out wheel cylinder bores. A drill motor with a 90-degree angle affords the best leverage and aim for getting into tight spots. The reversible option allows the drill to be pulled backward without chafing, or moved back and forth, which cross-hatches the cylinder bore, making for better surface smoothness. The variable speed feature allows the RPM to be increased or decreased on demand. The slow variable speed option also offers much safer material removal. Variable speed drills for brake cylinder honing perform best in 1/4- and 3/8-inch drive sizes.

Ball-type Abrasive Flex Hone

    The ball-type abrasive flex hone has aluminum oxide, abrasive sanding balls that extend from the shaft that fits neatly into the drill bit. These hones come in a variety of sizes that accommodate large- or small-bore wheel cylinders. The positioning of the sanding balls gives the flex hone a natural cross-hatch "rip" when inserted and extracted from the cylinder bore. The flex hone can finish the job in 20 seconds while using the forward thrust position and offer months of continuous use without being replaced. Shaft sizes allow for 1/4- and 3/8-inch drill motors.

Adjustable Metal Flex Stone Hone

    The unique design of the tri-rod metal flex hone makes for speedy and clean boring by using three metal extensions that have sanding pads on their ends. The stones come in kits which include a variety of stone sizes and grits. Fine, medium and coarse stones fit every application for rough cuts and final finishing. Cutting stones can be cleaned or replaced when needed. They can adapt to cylinder bores as small as 3/4 inch in diameter, all the way up to 2-1/2 inch.

Rotational Paper Sander

    Paper sanders fit through slots on drill bit shafts; and when coiled, they can be rotated inside the cylinder bore. Paper sanders allow for the flexibility of changing grits or replacing worn sandpaper. Hand dowels can be used manually by simply curling segments of sandpaper around the dowel. Thrusting them in and out of the cylinder bore, while turning, mirrors the cutting movements of drill-mounted flex hones and adjustable metal hones.

Read More.. >

Friday, October 25, 2013

How to Top Up Brake Fluid in a Ford Puma

The Ford Puma, manufactured from 1997 to 2001, is a compact sports coupe available in Europe. While the Puma never officially made it to the US, the car shared much of its technology, including the Zetec engine, with many US-branded Ford vehicles. The Puma uses DOT 4 synthetic brake fluid as its sole brake system fluid. This fluid, like many other brake fluids, is non-compressable and has a high resistance to attracting moisture. The brake fluid is filled through a reservoir mounted on top of the brake master cylinder.

Instructions

    1

    Turn off the engine and pop open the Pumas hood. Support the hood with the hood prop stick.

    2

    Locate the brake fluid reservoir on top of the master cylinder. It is made from white plastic and sits on the master cylinder that protrudes from the right rear section of the engine firewall.

    3

    Clean any dust, debris and dirt off of the reservoir cap with a clean shop rag. Remove the cap by turning it counterclockwise and set the cap aside.

    4

    Pour brake fluid into the reservoir until the level becomes even with the MAX mark imprinted on the left side of the reservoir.

    5

    Replace the cap, clean up any spilled brake fluid, and close the hood.

Read More.. >

Sunday, October 6, 2013

How to Hook Up the Brake Controller on the 2006 Duramax

Duramax is the name of an 8-cylinder 6.6-liter diesel engine that General Motors has manufactured since 2001. The 2006 version carries the LLY designation and is an option for many full-size Chevrolet pickup trucks. The braking system on vehicles with a 2006 Duramax engine includes an electronic brake control module. The function of the EBCM is to keep the wheels from locking during an emergency stop by applying less braking force to a wheel that is rotating more slowly than the other wheels.

Instructions

    1

    Remove the negative battery cable with a socket wrench to prevent anyone from inadvertently starting the engine. Raise the vehicle with a floor jack and support it on jack stands. Clean the area around the EBCM under the vehicle with a shop cloth to prevent contamination of the disassembled braking components.

    2

    Disconnect the mounting screws for the EBCM with a socket wrench and discard the mounting screws. Pull the EBCM down slightly to detach it from the brake pressure modulator valve, or BPMV. Discard the EBCM.

    3

    Clean the mounting surfaces on the BPMV with a clean shop cloth to ensure a good electrical contact between the EBCM and BPMV. Install the new EBCM to the BPMV with new mounting screws and fasten the mounting screws with a socket wrench.

    4

    Lower the vehicle with the floor jack. Attach the negative battery cable with a socket wrench.

    5

    Turn the ignition on. Connect a scan tool to the data link connector under the dashboard on the left side of the steering column. Check and clear any error codes that the scan tool displays.

Read More.. >