Showing posts with label f150. Show all posts
Showing posts with label f150. Show all posts

Monday, May 12, 2014

How to Change the Fuel Pump in a 1988 Ford F150

The Ford F series is a line of full-size pickup trucks in continuous production since 1948, with the F-150 models being the most popular. The 1988 Ford F-150 has an early form of fuel injection that uses a low-pressure electric fuel pump. The replacement of the fuel pump itself is a relatively simple task, but accessing the fuel pump requires you to remove the fuel tank. The great majority of the work in replacing the fuel pump on a 1988 Ford F-150 is the removal and installation of the fuel tank.

Instructions

    1

    Park the vehicle and turn off the ignition. Open and secure the hood. Disconnect the negative battery cable with a socket wrench and remove the fuel tank filler cap.

    2

    Remove the valve cap to the fuel pressure relief valve on the fuel line and connect the T80L-9974-A pressure gauge to the relief valve. Place the end of the hose for the pressure gauge into a gasoline-approved container. Open the pressure gauge valve. Drain the fuel from the fuel system into the container. Remove the pressure gauge and replace the valve cap on the relief valve.

    3

    Drain the fuel from the tank. Disconnect the wiring from the fuel-sending unit and the fuel line from the fuel tank. Remove the air relief tube from the fuel tank. Loosen the clamp on the filler neck hose and detach the filler neck from the fuel tank. Disconnect the mounting bolts for the fuel tanks retaining strap. Remove the fuel tank from the vehicle.

    4

    Detach the electrical wiring from the fuel-sending unit. Clean the fuel tank around the fuel sending unit and disconnect the fuel lines from the fuel sending unit. Turn the locking ring of the fuel sending unit counterclockwise with a hammer and wood dowel. Remove the locking ring and disconnect the fuel sending unit from the fuel tank. Discard the gasket on the fuel tank.

    5

    Put the new gasket into the groove on the tank. Install the new fuel-sending unit to the fuel tank while keeping the gasket in place. Align the tabs on the locking ring with the slots on the fuel tank and turn the locking ring clockwise until it is against the retainer ring tab.

    6

    Connect the fuel lines and electrical wiring to the fuel sending unit. Connect the fuel tank and tighten the nuts on the fuel tanks restraining strap to 30 foot-pounds with a torque wrench.

Read More.. >

Wednesday, May 7, 2014

How to Remove Install the CV Half Shaft on a 2007 Ford F150

Changing the half shaft on a 2007 Ford F150 pickup is a moderately challenging job for the do-it-yourself mechanic. Steering and suspension parts such as the half shaft, are exposed to the elements, and endure many stresses during use. The accumulated wear can make parts stubborn to remove. Read the following instructions caully before attempting the repair, and make sure you have the necessary parts and equipment on hand.

Instructions

    1

    Place the vehicle in neutral and raise it with the floor jack. Place jack stands securely under the vehicle frame rails.

    2

    Remove the wheel whose half shaft is to be replaced.

    3

    Remove the dust cap in the center of the wheel hub using a screwdriver and rubber mallet. You can also use channel lock pliers large enough to grip it.

    4

    Remove the wheel end nut and discard it.

    5

    Remove the two vacuum lines at the integrated wheel end, where the axle bolts to the wheel hub.

    6

    Remove the three integrated wheel end bolts securing the half shaft to the wheel hub.

    7

    Remove and discard the tie rod end nut. Separate the tie rod from the knuckle using a ball joint separator.

    8

    Remove and discard the upper ball joint nut. Separate the upper ball joint from the knuckle using a ball joint separator.

    9

    Hold the half shaft in. Allow the wheel hub assembly to swing away caully until there is enough clearance to remove the outboard end of the half shaft from the hub bearing. Take care not to damage the hub seal.

    10

    Remove the integrated wheel end from the half shaft.

    11

    Remove the six bolts attaching the half shaft flange to the axle flange. Separate the half shaft from the axle and remove the half shaft from the vehicle.

    12

    Install the integrated wheel end to the outer CV joint housing on the new half shaft. Take care not to dislodge the seal spring when installing.

    13

    Installation is the reverse of removal, using the following torque specifications: half shaft flange to axle flange bolts, 60 foot-pounds; upper ball joint and tie rod nuts, 110 foot-pounds; integrated wheel end bolts, 9 foot-pounds; wheel end nut, 18 foot-pounds.

Read More.. >

Tuesday, March 4, 2014

How to Bleed the Slave Cylinder on a 2004 F150

The 2004 Ford F-150 truck with a manual transmission is equipped with a hydraulic clutch release system. Pressure is generated within the clutch system by depressing the clutch pedal. The clutch pedal actuates the clutch master cylinder and supplies pressurized hydraulic fluid to the slave cylinder on the transmission. Air bubbles can become trapped and suspended within the hydraulic fluid, which can lead to a spongy feel at the clutch pedal and incomplete clutch disengagement. The 2004 F-150 trucks come equipped with either an internal or external type slave cylinder, depending on the engine size, and require a different bleeding procedure for each type.

Instructions

Internal Slave Cylinder

    1

    Set the parking brake and chock the rear wheels. Place a jack under the front jacking points on the frame rail behind the front wheels and lift the vehicle clear of the ground. Support the vehicle on jack stands.

    2

    Locate the clutch master cylinder within the engine compartment next to the brake booster and brake master cylinder. Clean the cap of the clutch master cylinder using a shop rag and remove the cap and diaphragm. Fill the master cylinder up to the Full mark with clean DOT 3 brake fluid.

    3

    Locate the clutch bleeder screw on the drivers side of the transmission, near where the hydraulic brake line enters the transmission. Install the clear vinyl tubing on the bleeder screw nipple and place the loose end of the tubing in a catch pan.

    4

    Loosen the bleeder screw and allow the fluid to drain from the system until the fluid stream is free of air bubbles. Ensure that the master cylinder does not run dry and add fluid as necessary. Close the bleeder screw.

    5

    Depress the clutch pedal fully and quickly release it 10 times in a row. Check and top off the fluid in the reservoir. Depress and release the clutch pedal five more times.

    6

    Install the clutch master cylinder diaphragm and cap.

    7

    Have a helper fully depress the clutch lever and hold it down. Open the bleeder screw slightly to release any residual air in the system. Close the bleeder screw and then have your helper release the clutch pedal. Repeat as necessary until the fluid stream is free of air bubbles.

    8

    Ensure that the fluid level in the master cylinder is up to the Full mark. Reinstall the cap and diaphragm.

    9

    Remove the jack stands and lower the vehicle.

External Slave Cylinder

    10

    Set the parking brake and chock the rear wheels. Place a jack under the front jacking points on the frame rail behind the front wheels and lift the vehicle clear of the ground. Support the vehicle on jack stands.

    11

    Locate the clutch master cylinder within the engine compartment next to the brake booster and brake master cylinder. Clean the cap of the clutch master cylinder using a shop rag and remove the cap. Fill the master cylinder up to the Full mark with clean DOT 3 brake fluid.

    12

    Locate the slave cylinder on the drivers side of the transmission. Push the cylinder into the transmission and rotate it counterclockwise until the cylinder disengages from the transmission. Remove the cylinder from the transmission.

    13

    Disconnect the hydraulic line support clip from the floor pan of the vehicle. Hold the slave cylinder with the hydraulic line up and the slave cylinder plunger down and the hydraulic line taking as straight of a path as possible to the master cylinder.

    14

    Slowly push the pushrod into the slave cylinder until it stops, then hold it for five to 10 seconds. Slowly release the pushrod and allow it to extend from the slave cylinder. Repeat this step as necessary until all the air is purged from the system and the fluid in the master cylinder is free of air bubbles.

    15

    Insert the slave cylinder into the transmission. Push the cylinder in while rotating it clockwise until it snaps into place. Install the hydraulic line support clip onto its mount on the floor pan.

    16

    Remove the jack stands and lower the vehicle to the ground using the jack.

    17

    Slowly depress the clutch pedal through its full range of motion and release it 25 times to complete the purging of air from the system.

    18

    Check the fluid level in the clutch master cylinder and fill it to the Full mark. Install the master cylinder cap.

Read More.. >

Sunday, February 2, 2014

How to Replace the Harmonic Balancer on a 1994 Ford F150

The Ford F-150 is a full-size pickup truck with a 3/4-ton capacity. Ford has manufactured this popular truck continuously since 1975. The 1994 F-150 belongs to the ninth generation of the Ford F-series. The crankshaft in this vehicle must have a counterweight to dampen harmonic vibrations that can occur when the crankshaft rotates at certain speeds. The harmonic balancer can be a separate weight or simply a weighted crankshaft pulley, depending on the engine.

Instructions

    1

    Disconnect the cooling fan shroud with a socket wrench, if you need additional clearance to access the crankshaft. Place a drain pan under the radiator drain and remove the drain plug with a socket wrench. Drain the coolant from the radiator into the drain pan and store the coolant for later use. Reinstall and tighten the drain plug.

    2

    Disconnect the coolant hoses from the radiator. Remove the bolts holding the radiator in place with a socket wrench and lift the radiator out of the vehicle. Turn the tensioner bolt for the drive belt counterclockwise with a box-end wrench to relieve the tension on the drive belt. Detach the drive belt from its pulleys.

    3

    Mark the crankshaft pulley and the crankshaft with white paint to ensure that you install the pulley to its original position. You only need to perform this step if the crankshaft damper and crankshaft pulley are separate components in your vehicle.

    4

    Disconnect the bolts that attach the crankshaft pulley to the crankshaft damper using a socket wrench. You only need to perform this step if the crankshaft damper and crankshaft pulley are separate components in your vehicle.

    5

    Remove the central retaining bolt from the crankshaft damper with a socket wrench. Pull the crankshaft damper from the crankshaft with a gear puller.

    6

    Align the key slot on the new crankshaft damper with the key on the crankshaft and mount the damper to the crankshaft. Tighten the central retaining bolt for the crankshaft damper with a socket wrench. Fasten the retaining bolts that attach the crankshaft damper to the crankshaft pulley if the damper and pulley are separate components on your vehicle.

    7

    Attach the drive belt to the crankshaft pulley. Install the radiator and cooling fan shroud if you removed these components earlier. Refill the radiator with coolant if necessary.

Read More.. >

Sunday, January 19, 2014

How to Change the Exhaust Manifold Gasket in a F150 4 6L Engine

The Ford F150s history spans back to the 1948 Ford F-1 half-ton pickup. In 1975, the F-150 was released as a bridge between the F-100 and F-250. The F-150 replaced the F-100 as the smallest of the F-series pickups in 1984. In 1997, Ford dropped the 5.0-liter engine and replaced it with the 4.6-liter V-8, which remained until the 2010 model year. The exhaust manifold gasket is the gasket that seals the connection between the exhaust manifold and the engine. When this gasket fails, it not only creates an exhaust leak, but it can also create a poor running condition.

Instructions

    1

    Loosen and remove the the EGR valve tube, only on the left exhaust manifold, with a combination wrench. Trace the oil dipstick tube downward and locate the point where its bracket bolts to the engine block. Loosen the bolt securing the bracket to the block, with a ratchet and socket, and pull the tube and dipstick from the engine.

    2

    Remove the nuts securing the exhaust manifold to the engine, using a ratchet and socket. If the nuts are frozen, apply a coat of rust penetrating spray to free them. Pry the manifold from the engine, using a 12-inch pry bar. Secure the manifold away from the engine using a bungee strap.

    3

    Pull the old manifold gaskets from the 4.6-liter. Use a wire brush to clean the gasket mating surface on both the exhaust manifold and the engine.

    4

    Place the new gaskets on the manifold studs protruding from the engine block. Each side of the 4.6-liter has two gaskets, one front and one rear.

    5

    Release the exhaust manifold from the bungee strap and place it on the studs protruding from the engine block. Hand-tighten all of the nuts to secure the manifold in place.

    6

    Tighten the nuts, in a crossing pattern starting from the upper rear bolt, to 13 to 16 foot-pounds of torque, using a torque wrench and a socket.

    7

    Place the dipstick tube back into the engine and tighten the bracket bolt with a ratchet and socket.

    8

    Reconnect the EGR valve tube to the exhaust manifold, if applicable, and tighten it to 26 to 33 foot-pounds with a torque wrench and combination wrench.

Read More.. >

Wednesday, January 15, 2014

How to Adjust Emergency Brake Cables on a 1997 F150

How to Adjust Emergency Brake Cables on a 1997 F150

You can adjust the emergency brake cables on your 1997 Ford F-150 yourself right from your home garage or driveway. This will save you a trip to the mechanic. When you park your F-150 on a downhill slope and the parking brake starts to slip, you know its time to adjust the cables on the parking brake. You just need a couple of tools purchased from your local auto parts retailer to get the job done. Start by parking the vehicle on level ground before making the adjustment.

Instructions

    1

    Step on the parking brake pedal, pressing it all the way to the floor.

    2

    Place wheel chocks in front of the front wheels and chocks behind the front wheels.

    3

    Put the floor jack under the back end of the vehicle and lift it up high enough to slid the jack stands underneath the F150 next to each wheel. Lower the vehicle onto the jack stands.

    4

    Get under the Ford and find the parking brake cable rod in the center of the vehicle. It is the rod with the cables coming to it. Hold the rod in place with your hand. Using pliers, tighten the equalizer nut about six turns.

    5

    Attach the cable tension gauge to the rear tension cable to measure and set the number of pounds of tension. Set the F-150s tension at 350 pounds.

    6

    Disengage the parking brake and spin the rear wheels to make sure they turn freely.

    7

    Adjust the parking brake equalizer nut so that it has a clearance of 0.38 mm if you find there is resistance when you spin the wheels.

    8

    Raise up the truck, remove the jack stands, lower the vehicle to the ground and remove the wheel chocks.

Read More.. >

Monday, November 18, 2013

How to Remove the 2001 F150 Steering Wheel

How to Remove the 2001 F150 Steering Wheel

A Ford F-150s steering wheel can be removed either for aftermarket options or for repair purposes. Because the steering wheel is in the way of the steering column and shaft, this is not the sort of task that can be done on a whim or an impulse. A specialized tool is involved.

Instructions

    1

    Pop the F-150s hood and prop it open. Disconnect the negative cable from the batterys negative terminal. Then, disconnect the positive battery cable. This disengages the F-150s airbags and restraint systems, keeping them from accidental triggering and deployment. Before proceeding, however, allow at least five minutes to pass. While you have put the airbags main power source off line, there will still be residual power within the F-150 that needs to drain off.

    2

    Disengage the battery to starter relay cable.

    3

    Pry off the oval covers over the airbag retaining screws with a small flat head screwdriver. Remove the screws underneath.

    4

    Lift the air bag unit off the steering wheel while keeping the trim cover "pointing" away from you. Even if disengage from electricity, there is still a risk of accidental deployment. Unplug the wiring around the F150s horn and air bags. Place the unit to the side, with the trim cover facing up.

    5

    Unscrew the steering wheel retaining bolt with a socket wrench and a socket wrench extension.

    6

    Mark the steering wheel and the steering wheel shaft with a marker. This will help align the steering wheel later, if you plan on reinstalling it.

    7

    Fit a two-jaw pulling tool over the steering wheel. Ensure the tool is firmly on, and adjust for tightness as needed.

    8

    Turn the two-jaw pulling tool for several rotations, until the steering wheel detaches from the steering shaft.

Read More.. >

Friday, November 15, 2013

How Do I Read 1995 Ford F150 Check Engine Codes

How Do I Read 1995 Ford F150 Check Engine Codes?

The Ford F-150s made in 1995 have check engine lights that come on when the computer system in the truck senses trouble. Sensors send information to the power train control of the truck when the information does not match up to what the trucks known limits are. The trucks computer generates a code and displays the check engine light. Each code refers to a specific issue that can be pinpointed once you have retrieved the code from the trucks onboard diagnostic system.

Instructions

    1

    Remove the cover off the diagnostic port of the Ford, located under the dashboard on the left-hand side.

    2

    Plug in the OBD scanner into the link of the diagnostic port. Code scanners can be found at your local auto-parts store. You can also ask a local auto-parts store if they can plug in a store-owned scanner for you to check the codes.

    3

    Run the self-test with the code scanner. Read the manufacturers instructions to find out how your particular scanner runs the self-test.

    4

    Write down the codes as the scanner reports them. There may be several codes--allow the scanner to run through the entire test.

    5

    Move through the codes as they appear, but do not delete them.

    6

    Remove the data cable and replace the cover over the port when complete.

Read More.. >

Tuesday, September 17, 2013

How to Install a 98 Ford F150 4 6 Head Gasket

The Ford F150 is a 1/2-ton pickup truck that has been in continuous production since 1975. The 1998 model belongs the tenth generation of this series, which includes F150s made from 1997 to 2004. A 4.6-liter V-8 engine is one of the options available for the Ford F150. Each side of the engine has a cylinder head that covers the four cylinders on that side. The cylinder head gasket lies between the engine block and the cylinder head.

Instructions

    1

    Discharge the air conditioning system with a refrigerant recovery machine, if your vehicle is equipped with AC. This step requires a mechanic certified by the Environmental Protection Agency.

    2

    Remove the cable from the negative battery terminal with a socket wrench. Disconnect the valve covers, and remove the intake manifold from the engine block. Detach the timing chains from the crankshaft sprocket and camshaft sprocket. Disconnect both exhaust manifolds from the engine block. Disconnect the air compressor to obtain access to the cylinder heads if your vehicle has air conditioning.

    3

    Disconnect the retaining bolts from the heater hose with a socket wrench. Squeeze the hose clamp and pull it down the hose to release the clamp. Detach the heater hose from the cylinder head. Disconnect the mounting bolts from the cylinder head and pull the cylinder head from the engine block. Discard the gasket for the cylinder head and remove any remaining gasket material from the engine block with a gasket scraper.

    4

    Turn the crankshaft clockwise until the key way on the crankshaft points straight up, and clean the cylinder head with a shop rag. Place the the new gasket for the cylinder head gasket over the dowel pins on the engine block, then mount the cylinder head on the engine block.

    5

    Fasten new mounting bolts to the cylinder head by hand. Tighten the mounting bolts to between 27 and 31 foot-pounds on the first pass with a torque wrench. Tighten the bolts another 85 to 95 degrees with a socket wrench on the second pass. Tighten the bolts another 85 to 95 degrees on the third pass.

    6

    Connect the heater hose to the cylinder head, and attach the hose clamp. Fasten the retaining bolts for the heater hose with a socket wrench. Connect the exhaust manifolds to the engine block, and mount the timing chain to the crankshaft sprocket and camshaft sprocket. Connect the intake manifold, and replace the valve covers.

    7

    Attach the cable for the negative battery terminal with a socket wrench. Start the engine and check for coolant leaks. Recharge the air conditioning system, if your vehicle is so equipped. This requires a mechanic certified by the EPA.

Read More.. >