Tuesday, May 13, 2014
How to Check to See If Water Pump Is Bad
Water pumps push coolant through a vehicles cooling system, using a fan belt or a timing belt. Water pumps can become faulty over time. There are usually signs that its going bad. If the problem is fixed in time, you can avoid costly repairs. You can check for a bad water pump in a few simple steps.
Instructions
Signs of a Bad Water Pump
- 1
Look for leaks from under the vehicle. When a water pump is going bad, one of the first signs is leaking coolant. Inspect the areas around the radiator and hoses for signs of leaking. If there is leaking, consult a mechanic immediately.
2Determine if there is overheating. Overheating is a sign that the water pump is leaking and needs immediate attention. Check the temperature gauge on the dashboard to see if it has risen into the hot zone. Also check to see if steam is rising from the engine.
3Look for pools of green fluid under your vehicle. This is another sign that the water pump is bad. After pulling out of a parking spot, check to see if a green fluid is on the ground underneath the vehicle.
4Listen for unusual sounds coming from the vehicle while driving. If you hear a whining sound coming from the heating or cooling vents, that indicates that there is a problem with the water pump.
Saturday, May 10, 2014
How to Clear the Check Engine Light on a 1995 Escort
You can clear the Check Engine light on your 95 Ford Escort using a computerized tool called an OBD I scanner. Retrieve the engine trouble codes using the OBD I scanner and make the necessary repairs before clearing the Check Engine light. If you clear the Check Engine light before repairing the Escort, you can damage the engine, the emissions system or the cars on-board diagnostics (OBD) computer.
Instructions
- 1
Locate the Diagnostic Link Connector (DLC) port on the drivers side dashboard under the steering column.
2Plug the OBD I scanner into the DLC port.
3Put the key into the ignition and turn it to the "On" position. This will power on the scanner.
4Select the "Clear Codes" or similar option. Wait for the scanner to return to the main menu. This will indicate that the task has been completed.
5Unplug the scanner and start the engine. Verify that the Check Engine light has shut off.
Thursday, December 26, 2013
How to Find the Check Engine Light Code for My 1994 Toyota
Back in the days before check engine light codes could be retrieved by using an OBD scanner, technician had to actually know how to retrieve the codes so that engine problems could be accurately diagnosed. Although technical advances have made it simple to retrieve check engine light codes on current model vehicles, the older cars such as in 1994 Toyota can still be accurately retrieved.
Instructions
- 1
Remove the rubber covers on the connectors diagnostic connectors. The diagnostic connectors are located in the engine compartment or by the kick panel under the dashboard on the passenger side. Refer to the manufacturers repair manual for the exact position of the diagnostic connector for your particular model 1994 Toyota.
2Connect either the TE1 and E1, or the T and E1 terminals in the diagnostic connectors by using a jumper wire. Refer to the manufacturers repair manual to ascertain which terminals should be jumped in and the location of the terminals to be jumped within the diagnostic connector on the particular model being diagnosed.
3Turn the ignition key to the "On" position. Any available codes can be determined by observing the flashing of the check engine light. For example, if the engine code is "41" the check engine light will flash four times and pause followed by one additional flash. If there are any additional codes they will be displayed after a 2.5-second pause.
4Refer to the 1994 Toyota manufacturers repair manual to decipher any codes that are retrieved.
5Disconnect the jumper wires and replace the rubber covers on the diagnostic connectors by pushing them back over the end of the diagnostic connector.
Thursday, December 19, 2013
How to Check a Coil Pack
The coil pack in a car is responsible for delivering a clean strong spark to the spark plugs. A defective coil pack can cause an intermittent spark, as well as a weak spark. Heat can create problems for a coil pack causing internal damage. You can check the coil with only a few tools and a basic knowledge of cars.
Instructions
- 1
Park the vehicle on level ground and set the emergency brake. Open the hood of the vehicle.
2Disconnect the spark plug wires from the spark plugs. Label the wires for proper replacement. Follow back the spark plug wires to the coil pack.
3Disconnect the coil pack by pulling on the electrical connector in the center of the pack.
4Remove the coil pack using the wrench to unbolt the support bracket. Place the coil on a work bench, with the terminal facing up.
5Turn on the volt meter and turn the dial to 20,000 ohms. Place the volt meter black lead to the center of the coil pack where the spark plug wire is connected. Place the red meter lead to the positive terminal on the coil. This checks the secondary resistance. Check the readings against your cars service manual to determine the proper operating range.
6Set the volt meter to 10 ohms, and touch the terminal "B+" found on top of the coil. Use the red meter lead. Touch the negative terminal with the black meter lead. This will test the primary resistance. Check the readings against the vehicles service manual for proper range of operation.
Tuesday, November 26, 2013
How to Check the Speed Sensor on a 99 Chevy Silverado
When the speed sensor on a 1999 Chevrolet Silverado begins to fail, the first noticeable sign may be a fluctuating speedometer. The speedometers needle may jump from one speed to another, or fall to zero and then suddenly return to the correct speed. The vehicle speed sensor, or VSS, is the sensor responsible for relaying the vehicles speed to the engine computer. In addition to using data from the VSS to calculate the vehicles speed, it also uses this data to make other computational decisions, including when to shift the transmission. The VSS is located on the tailshaft of the transmission or on transfer case in four wheel drive models. The sensor itself is a magnetic inductive sensor that monitors the magnetic field around a notched, reluctor wheel affixed to the tailshaft. The notches in this wheel interfere with the sensors magnetic field and the engine computer calculates the frequency of this interference and converts it into a speed value.
Instructions
- 1
Turn off the engine, but leave the ignition on. Connect a scan tool to the Silverados scan tool terminal.
2Navigate to the live data menu and select VSS. Test drive the vehicle in a safe, controlled area such as an empty parking lot where there is no possibility of hitting other cars or objects.
3Look down at the scan tools display and note the speed value for the VSS. It should reflect the vehicles current speed. If the speed displayed is 0 or different from the speedometer reading, its likely there is a problem with the VSS or the VSS harness connector.
4Note the voltage value for the VSS on the scan tool. This value should be listed below or above the VSS speed value. It should read between 1.5 and 12 volts. If the value is outside this range, the VSS is either not receiving the proper voltage or is faulty.
5Raise the vehicle with an automotive jack and support it with jack stands. Locate the VSS on the tailshaft of the transmission of transfer case for vehicles equipped with four wheel drive. Disconnect the VSSs electrical connector.
6Turn the ignition on and probe the light blue wire on the connector with a digital multimeter set to DC volts. The multimeter should show between 1.5 and 12 volts. Connect a test lamp to a positive voltage source and probe the black, ground wire on the VSS connector. The test lamp should illuminate if the ground properly connected. If the ground is OK and you find voltage at the connector, then the VSS is faulty and needs to be replaced.
Friday, November 15, 2013
How Do I Read 1995 Ford F150 Check Engine Codes
The Ford F-150s made in 1995 have check engine lights that come on when the computer system in the truck senses trouble. Sensors send information to the power train control of the truck when the information does not match up to what the trucks known limits are. The trucks computer generates a code and displays the check engine light. Each code refers to a specific issue that can be pinpointed once you have retrieved the code from the trucks onboard diagnostic system.
Instructions
- 1
Remove the cover off the diagnostic port of the Ford, located under the dashboard on the left-hand side.
2Plug in the OBD scanner into the link of the diagnostic port. Code scanners can be found at your local auto-parts store. You can also ask a local auto-parts store if they can plug in a store-owned scanner for you to check the codes.
3Run the self-test with the code scanner. Read the manufacturers instructions to find out how your particular scanner runs the self-test.
4Write down the codes as the scanner reports them. There may be several codes--allow the scanner to run through the entire test.
5Move through the codes as they appear, but do not delete them.
6Remove the data cable and replace the cover over the port when complete.
Monday, November 11, 2013
How to Reset the Check Engine Light in a Toyota Corolla
Any Toyota Corolla made in 1996 or later will come with an On-board Diagnostics II computer (OBD II). When the check engine light illuminates on the Corolla, it is coming from an error code sent from a sensor to the computer in the car. It indicates a problem that needs to be addressed by a qualified mechanic as soon as possible or you may risk further damage to the vehicle. After the problem has been diagnosed and repaired, you can reset and erase the light yourself at home with just a few moments of your time.
Instructions
- 1
Find the Diagnostic Link Connector (DLC) on the lower left side of the dashboard on the drivers side of the car. You can find it near the hood release.
2Plug an OBD II scanner into this port and put the key in the ignition. Turn the key forward about two clicks, taking care not to start the engine. This will power the scanner.
3Scroll through the menu on the scanner using the arrow keys until you find the command that says "Erase Codes." Press "Enter." (Some scanners have a separate "Erase" button that you can press instead.) Wait for the main menu to appear or until you see the message on the scanner that says "Command Sent."
4Unplug the OBD II scanner and start the vehicle. Look at the instrument panel to make sure the check engine light has turned off.
Friday, November 1, 2013
How to Properly Check Vehicle Ball Joints
Vehicle ball joints often go bad over the course of vehicle ownership, and must be replaced to prevent uneven tire wear. The first sign of a bad ball joint is when you hear a distinctive "clunk" sound when the vehicle is being turned at a slow speed. Once you are suspicious of having a defective ball joint, you can take the next step to determining how bad the problem is.
Instructions
- 1
Position the vehicle on a flat, level surface and set the parking brake.
2Jack up the front of the vehicle and support the frame with jack stands so that both front wheels of the vehicle are off the ground.
3Place your hands on the tire, one at the 12 oclock position and one at the 6 oclock position. Work the top and bottom of the tire back and forth. If the tire moves back and forth, the ball joint is failing. If the tire moves more than 15 degrees, then the ball joint has already failed and must be replaced. If the tire does not move at all, then the ball joint is undamaged.
Friday, September 27, 2013
How to Check for Worn Wheel Bearings
Wheel bearings are important parts of the suspension system of your vehicle. They help support the weight of your vehicle and allow the steering wheel to rotate with the least amount of friction. Like all automobile parts, wheel bearings wear out over time. Worn wheel bearings can be dangerous and must be replaced immediately. Driving with severely worn-out wheel bearings can cause you to lose control of your vehicle.
Instructions
- 1
Feel for vibrations or wobbling from your steering wheel while you drive. Your steering wheel will shake and sometimes cause you to pull your car to the side when you apply your brakes.
2Listen for a squealing noise that gets louder as your car picks accelerates. Hearing this noise coming from your tires or steering wheel indicates that the wheel bearings are worn.
3Listen for grinding noises coming from the steering wheel as you drive. A grinding noise is the most common noise youll hear and is indicative of worn-out wheel bearings.
4Feel for looseness in the wheel while driving. Any looseness indicates a worn-out wheel bearing.