Tuesday, April 22, 2014
How to Pull Codes From a 1995 Chevy
You can pull the codes from your 1995 Chevy right in your garage, saving you time and money. When your Chevy is having problems, you might see a warning light such as "Check Engine" illuminate on its instrument cluster. This light ers to a problem with one of the vehicles sensors. Before repair the vehicle, you must troubleshoot the problem with an OBD I scan tool you can purchase from your local auto parts retailer.
Instructions
- 1
Park the vehicle and turn off the ignition. Find the open OBD port under the steering column. Plug the OBD I scan tool into the open port.
2Put the key into the ignition and turn it to the "ACC" position and do not start the engine.
3Turn on the OBD I scan tool and wait for it to read the codes.
4Wait for the display on the OBD I scan tool to read "OK," then turn off the ignition and the scan tool.
5Select the "Menu" command and scroll through it until you see "Stored Codes." Select this option and write down the alphanumeric codes on a piece of paper.
6Look up the codes in the scan tools manual. Unplug the scan tool and have your Chevy serviced or repaired according to the diagnostic codes.
Friday, March 7, 2014
Transmission Codes for Chevy Blazers
If your Chevy Blazer is not working correctly, you can use General Motors trouble code numbers to help diagnose the problem. The code numbers are read via a scan tool plugged into the vehicle diagnostic connector under the instrument panel. According to AA1Car, for some code numbers the same number may be used for different faults on different model years or models. After youve figured out the code, further testing must be done before repairs are made, AA1Car warns.
P1500 and P1600 Codes
P1521 is defined as transmission engaged at high throttle angle. P1527 is transmission range/pressure switch comparison. P1623 is transmission temp pull-up resistor.
P1700 Codes
P1700 is transmission MIL request. P1701 is transmission MIL request circuit. P1740 is transmission torque reduction request circuit. P1760 is transmission control module supply voltage interrupted. P1792 is ECM to transmission control module engine coolant signal.
P1800 Codes
P1800 is ECM to transmission control module engine coolant signal. P1812 is transmission over temperature condition. P1815 is transmission range switch-start in wrong range. P1819 is transmission range switch out of range, possible no start. P1820 is transmission range switch A voltage low. P1822 is transmission range switch B voltage high. P1823 is transmission range switch P voltage low. P1825 is transmission range switch A, B, C and P signals invalid. P1826 is transmission range switch C voltage high. P1845 is transmission gear ratio output circuit. P1868 is transmission fluid life. P1870 is transmission component slipping.
Thursday, March 6, 2014
How to Access Trouble Codes on a 1994 BMW 530i
You can access trouble codes on your 94 BMW 530i right from your home garage, saving yourself time and money. To access the codes you must purchase or borrow an OBD I code scanner. These small, computerized devices are available at your local auto parts retailer. The scanner reads trouble codes stored in the vehicles On-Board Diagnostics computer. Each code gives you specific information about the vehicle to help you diagnose the problem with your BMW.
Instructions
- 1
Locate a port on the drivers side dashboard near the steering column. This port is the same size and shape as the connector end on the OBD I code scanner. Plug the scanner into the port, taking care not to shove it in and bend the pins.
2Put the key into the ignition and turn it to the "On" position, but dont crank the engine. This will power on most scanners. If not, look for an "on/off" button on the scanner and press it.
3Select "Retrieve Codes" or other similar command on the scanner. Wait for the scanner to display the trouble codes. Write them down on a piece of paper. Look up the codes in the code scanners manual.
4Unplug the scanner and have the vehicle serviced or repaired based on the diagnostic trouble codes.
Thursday, December 5, 2013
How to Pull Codes for a 1988 Mazda RX7
You can pull the codes from your 88 Mazda RX7 using a small computerized device known as an OBD I code reader. These tools can be purchased at any auto parts store. The Mazda RX7 comes equipped with an On-Board Diagnostics I computer (OBD I), which receives and stores trouble codes sent to it from sensors found throughout the vehicle. When a sensor detects a malfunction and sends a code to the computer, the computer illuminates a warning or service light on the instrument panel.
Instructions
- 1
Locate the diagnostic port found on the drivers side dash. Plug the code reader into this port.
2Put the key into the ignition and turn it to the "on" position, but dont start the vehicle. This will turn on most code readers. If not, find the on/off switch on the reader and turn it on.
3Wait for the code reader to interface with the Mazdas computer. Most readers will retrieve the codes automatically; for some readers you have to select the "Retrieve Codes" command on the face of the reader.
4Write down the codes the reader displays and look up their meanings in the code readers manual.
5Unplug the code reader and turn off the vehicle. Have the Mazda serviced or repaired based on the information obtained from the codes.
Friday, November 15, 2013
How Do I Read 1995 Ford F150 Check Engine Codes
The Ford F-150s made in 1995 have check engine lights that come on when the computer system in the truck senses trouble. Sensors send information to the power train control of the truck when the information does not match up to what the trucks known limits are. The trucks computer generates a code and displays the check engine light. Each code refers to a specific issue that can be pinpointed once you have retrieved the code from the trucks onboard diagnostic system.
Instructions
- 1
Remove the cover off the diagnostic port of the Ford, located under the dashboard on the left-hand side.
2Plug in the OBD scanner into the link of the diagnostic port. Code scanners can be found at your local auto-parts store. You can also ask a local auto-parts store if they can plug in a store-owned scanner for you to check the codes.
3Run the self-test with the code scanner. Read the manufacturers instructions to find out how your particular scanner runs the self-test.
4Write down the codes as the scanner reports them. There may be several codes--allow the scanner to run through the entire test.
5Move through the codes as they appear, but do not delete them.
6Remove the data cable and replace the cover over the port when complete.