Showing posts with label mazda. Show all posts
Showing posts with label mazda. Show all posts

Wednesday, April 30, 2014

How to Replace the Heater on a 1992 Mazda B2600

The heater in the 1992 Mazda B2600 is a radiator that uses hot coolant from the engine to heat the cab of the truck. The procedure for replacing the heater is the same for all Mazda trucks made from 1987 to 1993.

Instructions

    1

    Disconnect the negative battery cable with a socket wrench to ensure the engine doesnt start while replacing the heater. Put a drain pan under the radiator, and open the drain plug. Allow the coolant to drain from the radiator, and replace the drain plug.

    2

    Disconnect the shield for the water valve on the heaters left side with a socket wrench. Detach the coolant hoses from the heater, and remove the housing for the control cable from its mounting clip on the heater. Disconnect the cable wires from the heaters crank arms. Detach the electrical connector from the fan motor.

    3

    Remove the glove compartment with a socket wrench to provide clearance for the heater. Disconnect the retaining nuts for the heater that are inside the glove compartment. Detach the defroster ducts from the heater, and pull the heater from the dashboard.

    4

    Mount the new heater to the dashboard, and align the mounting studs on the heater with the corresponding holes in the dashboard. Fasten the mounting nuts for the heater, and attach the defroster ducts to the heater. Attach the control cable for the defrost door for the heater to the crank arm.

    5

    Turn the upper control lever to the heat position, and push the crank arm for the heater towards its mounting clip as far as possible. Attach the cable housing to the clip, and fasten the clip to the heater with a socket wrench.

    6

    Attach the control cable for the water valve to the lever for the water valve. Set the heaters control lever to the hot setting, and push the crank arm for the lever as far towards the mounting clip for the control cable as possible. Fasten the screw for the clip with a socket wrench.

    7

    Insert the control cable for the recirculation door into the doors crank arm. Bend the cable, and fasten it into place with the retaining screw. Move the center control lever to the REC setting, and push the crank arm for the recirculation door toward the mounting clip as far as possible.

    8

    Attach the housing for the recirculation door cable to its clip, and fasten the retaining screw for the clip with a socket wrench. Connect the electrical connector for the fan motor. Attach the coolant hoses to the tubes on the left side of the heater, and fasten the hose clamps. Connect the shield for the heaters water valve with the retaining screws, and install the glove compartment.

    9

    Replace the coolant in the radiator, and reconnect the cable to the negative battery terminal with a socket wrench. Check for coolant leaks, and ensure the heater is functioning properly.

Read More.. >

Sunday, March 9, 2014

Troubleshooting a Mazda MPV

Troubleshooting a Mazda MPV

Mazdas MPV is a sedan-style car that is perred by consumers for its fuel economy. If you are having problems with your Mazda MPV, there are several things that you can do before you take it to a service shop. Dead batteries, no gas, or a low coolant level can lead to the Mazda MPV not starting. You dont have to be a Mazda technician to get your MPV back on the road. You can generally do it yourself with little hassle.

Instructions

    1

    Turn the key in the MPVs ignition and look over the instrument panel. Check the fuel level and the battery charge to determine if this is your problem. If you hear a clicking noise when your turn the key, you need to have your alternator replaced by a service technician.

    2

    Fill the gas tank with gasoline if needed. Pop the hood to your Mazda MPV and look over the battery connections. The battery is located on the right side of the engine. The battery should be properly connected to the terminals. Use a pair of channel locks to tighten the cable connections to the battery terminals.

    3

    Use a voltmeter to test the battery charge. Hold the leads of the voltmeter to the terminals on the top of the battery. You should get a 12V reading. If you dont get a 12V reading, you can jump the battery.

    4

    Have a friend hook jumper-cables up to their car battery and then connect the other ends of the jumper cable to your cars battery. Start the other car and then try to start your MPV. Allow the battery to charge for about 10 minutes before you turn the MPV off. Try to restart the MPV. If the MPV doesnt restart, the battery is dead and you will need to replace it.

    5

    Check over the coolant system if your MPV is overheating. Locate the coolant tank on the left side of the engine. Look for the fill line on the edge of the tank. Make sure that you coolant is filled to the fill line. If the coolant is not filled to that line, fill it with 50/50 coolant.

Read More.. >

Thursday, January 16, 2014

My Mazda 6 Wont Start and Dials Bounce

My Mazda 6 Wont Start and Dials Bounce

The Mazda 6 was first introduced in 2002 as a mid-sized sedan. If you are having problems starting your Mazda 6, there are several things that you can do before you take the car to a mechanic. The dials in your Mazda 6 will bounce if the engine is trying to crank. Some common problems are a low charge on the battery and no fuel in the gas tank. You can troubleshoot your Mazda 6 to find out the problem, but a major repair should only be handled by a professional mechanic.

Instructions

    1

    Turn the Mazda 6s key in the ignition. Listen for the engine to crank. If you dont hear the engine crank, you probably have a dead battery.

    2

    Open the hood of your Mazda 6 and look over the battery terminals. Use a socket wrench to tighten the terminals if needed.

    3

    Take the battery terminals off of the battery and pour a little bit of soda onto them. Scrub the areas with a wire brush to take any corrosion off.

    4

    Use jumper cables and another car to jump-start the Mazda 6. Leave the car running for about 10 minutes to get the battery charged. If you smell something like rotten eggs coming from your battery, you will need to replace it.

    5

    Add one gallon of gasoline to your Mazda 6 and then try to start the car. If your gas gauge is broken, you could be out of fuel.

Read More.. >

Thursday, December 5, 2013

How to Pull Codes for a 1988 Mazda RX7

How to Pull Codes for a 1988 Mazda RX7

You can pull the codes from your 88 Mazda RX7 using a small computerized device known as an OBD I code reader. These tools can be purchased at any auto parts store. The Mazda RX7 comes equipped with an On-Board Diagnostics I computer (OBD I), which receives and stores trouble codes sent to it from sensors found throughout the vehicle. When a sensor detects a malfunction and sends a code to the computer, the computer illuminates a warning or service light on the instrument panel.

Instructions

    1

    Locate the diagnostic port found on the drivers side dash. Plug the code reader into this port.

    2

    Put the key into the ignition and turn it to the "on" position, but dont start the vehicle. This will turn on most code readers. If not, find the on/off switch on the reader and turn it on.

    3

    Wait for the code reader to interface with the Mazdas computer. Most readers will retrieve the codes automatically; for some readers you have to select the "Retrieve Codes" command on the face of the reader.

    4

    Write down the codes the reader displays and look up their meanings in the code readers manual.

    5

    Unplug the code reader and turn off the vehicle. Have the Mazda serviced or repaired based on the information obtained from the codes.

Read More.. >

Saturday, October 19, 2013

How Do I Reset an Airbag in a 2001 Mazda B3000

How Do I Reset an Airbag in a 2001 Mazda B3000?

The Supplemental Restraint System (SRS) or airbag light on a 2001 Mazda B3000 is designed to alert the driver to malfunctions in the airbag system. The light may illuminate on the instrument panel for reasons unrelated to the airbag, or it may illuminate because of a real problem that needs to be addressed. If you have recently replaced the vehicles battery or installed a new stereo, theres a good chance that the airbag just needs to be reset. Perform the following steps to shut off the light. If the light turns itself back on, then you should take it to a qualified mechanic to have the airbag system examined.

Instructions

    1

    Insert the key into the ignition and turn it to the "ACC" position then turn it off again. Do this 10 times quickly but do not start the engine. If this procedure does not reset the SRS light, proceed to Step 2.

    2

    Locate the fuse panel cover on the drivers side dashboard. Open the panel by pulling down on the cover from the top by hand. Locate the SRS fuse by referring to the fuse diagram. Pull the fuse out with the fuse puller and examine it to see if it has blown. If it has, replace it. This should reset the light. If not, proceed to Step 3.

    3

    Pop the hood on your Mazda B3000 and loosen the bolt on the negative cable clamp with a pair of pliers. Slip the clamp off the negative battery terminal, taking care not to let it touch anything. Wait about 10 minutes then reconnect it to the terminal and tighten the bolt. Close the hood and start the engine. Examine the instrument panel to verify that the SRS light has shut off.

Read More.. >

Saturday, October 12, 2013

What Is an EGR in a Mazda 626

What Is an EGR in a Mazda 626?

An exhaust gas recirculation system is a very important automobile component. It plays a large role in keeping each automobiles emissions from polluting the atmosphere to a large extent.

Function

    The primary function of an EGR system in a Mazda 626 is the same as it is in any car -- to reduce nitrous oxide emissions. When the combustion chamber in a cars engine gets too hot, nitrous oxide can form. The EGR system prevents this by recirculating exhaust into the intake stream to cool down the combustion process.

Significance

    When nitrous oxide is formed in a cars combustion chamber and released, it can combine with hydrocarbons to form smog. The exhaust gas recirculation system is a means of reducing nitrous oxide production and thereby reducing the harmful emissions of your Mazda 626 or any other automobile.

Considerations

    In considering an exhaust gas recirculation system in a Mazda 626, there are a few things you should take into account. The EGR system must control the flow of recirculated exhaust very precisely. This is partly to maintain national standards and partly because the performance of the EGR system will affect the cars performance as a whole. Too much flow may cause a lull in acceleration, and too little flow may cause engine ping.

Read More.. >