Showing posts with label 6. Show all posts
Showing posts with label 6. Show all posts

Sunday, March 9, 2014

The Clifford 6 Cylinder Performance

The Clifford Performance company manufactures parts and accessories to increase the performance of six-cylinder engines to match the performance of larger V-8 engines.

History

    Clifford Performance was established as Clifford Research by aerospace engineer Jack Clifford in 1967. Jack Clifford began developing automobile parts because of his interest in drag racing during the 1950s, which he used to increase the performance of a 1954 Hudson Flathead 6 engine.

Performance

    To increase the performance of six-cylinder engines produced in the U.S. in the 1960s, Clifford designed modified parts for the intake and exhaust systems, including an exhaust header and intake manifold. These modifications gave six-cylinder engines a similar performance to the larger, more powerful V-8 engines.

Design

    Clifford Performance is headquartered in Wildomar, California, where the company manufactures exhaust headers, cams and intake manifolds. Exhaust headers produced by Clifford Performance are created using 16 gauge tubing.

Read More.. >

Thursday, February 20, 2014

How to Turn the Distributor on a 1985 Camaro 2 8 With a V 6 Engine

The distributor on the 1985 Chevrolet Camaro is the main component that the spark plugs receive their voltage from. The distributor also supplies the proper firing order to the spark plugs to keep the engine in time. The gears on the bottom of the distributor shaft are turned by the camshaft. As the camshaft turns the distributor shaft, the distributor shaft turns the rotor inside of the distributor cap. The rotor then turns inside of the distributor cap and supplies the spark plugs with the proper amount of voltage to keep the engine timed.

Instructions

    1

    Park the 1985 Chevrolet Camaro in a safe working area and open the hood. Shut the motor off and engage the parking brake.

    2

    Raise the hood and prop it in place. Locate the distributor cap near the back of the engine. All of the spark plug wires are attached to the top of the distributor cap.

    3

    Mark a straight line on the front side of the distributor cap with a marker. Also mark another straight line on the front side of the distributor cap base directly below the other line. This will help you remember the exact setting of the distributor before moving it.

    4

    Loosen the hold-down screws on the bottom side of the distributor with a Phillips-head screwdriver.

    5

    Grab the distributor with both hands and turn it clockwise to retract the timing. Turn the distributor counterclockwise to advance the timing. Be sure to make short turns when turning the distributor. Once the distributor is timed to your liking, screw the hold-down screws back down tight with the Phillips-head screwdriver.

Read More.. >

Thursday, January 16, 2014

My Mazda 6 Wont Start and Dials Bounce

My Mazda 6 Wont Start and Dials Bounce

The Mazda 6 was first introduced in 2002 as a mid-sized sedan. If you are having problems starting your Mazda 6, there are several things that you can do before you take the car to a mechanic. The dials in your Mazda 6 will bounce if the engine is trying to crank. Some common problems are a low charge on the battery and no fuel in the gas tank. You can troubleshoot your Mazda 6 to find out the problem, but a major repair should only be handled by a professional mechanic.

Instructions

    1

    Turn the Mazda 6s key in the ignition. Listen for the engine to crank. If you dont hear the engine crank, you probably have a dead battery.

    2

    Open the hood of your Mazda 6 and look over the battery terminals. Use a socket wrench to tighten the terminals if needed.

    3

    Take the battery terminals off of the battery and pour a little bit of soda onto them. Scrub the areas with a wire brush to take any corrosion off.

    4

    Use jumper cables and another car to jump-start the Mazda 6. Leave the car running for about 10 minutes to get the battery charged. If you smell something like rotten eggs coming from your battery, you will need to replace it.

    5

    Add one gallon of gasoline to your Mazda 6 and then try to start the car. If your gas gauge is broken, you could be out of fuel.

Read More.. >

Thursday, November 7, 2013

6 0 Powerstroke Issues

The 6.0-liter Powerstroke was a turbo-diesel engine used in a wide variety of Ford trucks and vans. Until 2007, all Powerstroke engines were made by a subcontractor, Navistar. Unfortunately, Navistar had poor quality controls and all the engines produced by Navistar had numerous problems. The 6.0-liter Powerstroke cost Ford millions in warranty repairs, in addition to the extra cost of redesigning the engines.

Unreliable Variable Vane Turbocharger Solenoid

    All turbo-diesels rely on a turbocharger to properly burn the fuel/air mixture. On the Powerstroke, a variable vane is used to adjust the air intake coming from the turbocharger into the engine. A solenoid controls the degree of rotation of the vane. On Navistar Powerstrokes the solenoid detaches easily, in addition to corroding early. Damage to the solenoid prevents the variable vane from changing position. A Powerstroke with a damaged solenoid will suffer power loss throughout the power band.

Carbon Deposits

    All Navistar engines, not just the Powerstrokes, suffer from excessive carbon deposits. Carbon deposits are a byproduct of the combustion of carbon-based fuels like diesel. In a well-designed engine the carbon is pushed out during the exhaust cycle of the combustion chamber. Unfortunately Navistar did not get the fuel injection timing right, and carbon builds up with each combustion cycle. A Powerstroke with carbon buildup shows excessive black exhaust smoke as well as power loss at higher engine speeds.

Defective Exhaust Back Pressure (EBP) Sensor

    The exhaust back pressure sensor tells the engine how much resistance is in the exhaust system. Excessive back pressure can choke the engine and the turbocharger. In the 6.0-liter Powerstroke, the sensor detaches easily from the exhaust system, depriving the ECU of any data. A detached sensor will lead to exhaust gases flowing back into the combustion chambers, stalling the engine. Additionally, the exhaust gases will flow back into the turbocharger and stop it from spinning.

Fuel Injector Harness Chafing

    The most dangerous defect in the 6.0-liter Powerstroke is the easily damaged fuel injector harness. The lines are laid across the engine support struts, which shift as the engine torques. This shifting chafes the fuel lines to the point of leaking. Even though diesel fuel is less flammable than regular gas, it is still a fire hazard. Do not operate any vehicle that is leaking fuel. If there are fuel puddles under the engine, then the fuel lines have been damaged. Contact a Ford dealership for repairs. Ford has bought back some trucks with this issue rather than pay for the repairs.

Read More.. >

Wednesday, October 9, 2013

How to Install an Oil Pump in a 6 5 Turbo Diesel

General Motors manufactured a 6.5-liter diesel engine from 1992 to 1999. It typically had a turbocharger and was most common in heavy trucks made by General Motors during this period. The purpose of the oil pump is to lubricate the moving parts by circulating oil through the engine. The oil pump on the General Motors 6.5-liter turbo diesel engine is under the engine, and is part of the oil pan assembly.

Instructions

    1

    Raise the vehicle and support it on jack stands. Place a drain pan under the drain hole in the crankcase. Remove the drain plug with a socket wrench, and let the oil drain into the pan. Replace the drain plug.

    2

    Rotate the crankshaft manually so that the No. 1 and No. 2 connecting rods are in the up position. Remove the mounting bolts for the oil pan with a socket wrench. Lower the oil pump to gain access to the fuel pump.

    3

    Disconnect the mounting bolts for the oil pump with a socket wrench. Allow the oil pump and its extension shaft to fall into the oil pan. Detach the pan from the vehicle.

    4

    Mount the new oil pump into position on the main bearing cap. Align the extension shaft with the oil pump drive and push the pump into place. Fasten the mounting bolts for the oil pump and tighten them to 65 ft. lbs. with a torque wrench.

    5

    Install the oil pan with a socket wrench and lower the vehicle. Fill the engine with oil. Start the engine and correct any oil leaks.

Read More.. >

Tuesday, September 17, 2013

How to Install a 98 Ford F150 4 6 Head Gasket

The Ford F150 is a 1/2-ton pickup truck that has been in continuous production since 1975. The 1998 model belongs the tenth generation of this series, which includes F150s made from 1997 to 2004. A 4.6-liter V-8 engine is one of the options available for the Ford F150. Each side of the engine has a cylinder head that covers the four cylinders on that side. The cylinder head gasket lies between the engine block and the cylinder head.

Instructions

    1

    Discharge the air conditioning system with a refrigerant recovery machine, if your vehicle is equipped with AC. This step requires a mechanic certified by the Environmental Protection Agency.

    2

    Remove the cable from the negative battery terminal with a socket wrench. Disconnect the valve covers, and remove the intake manifold from the engine block. Detach the timing chains from the crankshaft sprocket and camshaft sprocket. Disconnect both exhaust manifolds from the engine block. Disconnect the air compressor to obtain access to the cylinder heads if your vehicle has air conditioning.

    3

    Disconnect the retaining bolts from the heater hose with a socket wrench. Squeeze the hose clamp and pull it down the hose to release the clamp. Detach the heater hose from the cylinder head. Disconnect the mounting bolts from the cylinder head and pull the cylinder head from the engine block. Discard the gasket for the cylinder head and remove any remaining gasket material from the engine block with a gasket scraper.

    4

    Turn the crankshaft clockwise until the key way on the crankshaft points straight up, and clean the cylinder head with a shop rag. Place the the new gasket for the cylinder head gasket over the dowel pins on the engine block, then mount the cylinder head on the engine block.

    5

    Fasten new mounting bolts to the cylinder head by hand. Tighten the mounting bolts to between 27 and 31 foot-pounds on the first pass with a torque wrench. Tighten the bolts another 85 to 95 degrees with a socket wrench on the second pass. Tighten the bolts another 85 to 95 degrees on the third pass.

    6

    Connect the heater hose to the cylinder head, and attach the hose clamp. Fasten the retaining bolts for the heater hose with a socket wrench. Connect the exhaust manifolds to the engine block, and mount the timing chain to the crankshaft sprocket and camshaft sprocket. Connect the intake manifold, and replace the valve covers.

    7

    Attach the cable for the negative battery terminal with a socket wrench. Start the engine and check for coolant leaks. Recharge the air conditioning system, if your vehicle is so equipped. This requires a mechanic certified by the EPA.

Read More.. >