Showing posts with label with. Show all posts
Showing posts with label with. Show all posts

Wednesday, May 21, 2014

Problems With 2007 Volkswagen Jetta

The 2007 Volkwagen Jetta, of German manufacturing, has several problems to consider before purchasing the vehicle. It weathered two serious recalls, which could have greatly impaired the cars performance and even endangered the driver if not fixed. It also has many consumer complaints dealing with various aspects of the car ranging from mechanical failures to cost spent in repairing these issues.

Headlights

    In Sept. 2007, a recall was issued for 2007 Volkswagen Jettas because of a malfunction in their headlights. Some vehicles may not have received a cap that disables horizontal aim of the headlights and some vehicles may have contained a cap that disabled the vertical aiming screw. This means that the nighttime illumination of the roadway would have been partially disabled and could contribute to a crash.

Driveshaft Screws

    In May 2009, a recall was issued for 2007 Volkswagen Jettas because of loose screws near the driveshaft cover. These screws may not have been properly torqued and could loosen over time, creating a knocking sound when the vehicle was in motion. They could also loosen to the point where the driveshaft could detach from the gearbox. The driveshaft could cause damage to the gearbox in a moving Jetta, damaging the gearbox and causing it to leak oil onto the highway. This could be a potential threat for the driver of the Jetta and other drivers on the roadway.

Other Problems

    The 2007 Jetta also has a list of other problems that were not widespread enough to cause recalls. Drivers found problems with their engine, transmission and driveline, steering and suspension, brakes, heating and air conditioning, starting and charging and car accessories. Excessive complaints have been raised about the engine. At certain times the car will not start. Aside from the problems, 2007 Jetta parts are quite expensive to buy and repair, financially setting many drivers back.

Read More.. >

Thursday, April 17, 2014

How to Weld Stainless Steel With Stick Welder

How to Weld Stainless Steel With Stick Welder

Stick or ARC welding stainless steel requires the use of a welding rod that is compatible with the chemical makeup of the stainless steel you are welding. You can use a higher purity stainless steel welding rod for lower grade stainless steel, but not vice versa. For example, a 316L rod can weld 304-grade stainless steel, but you cannot produce a weld with structural integrity using a 309L rod to weld 316-grade stainless steel; this is due to crystalline structures that form in the weld joint.

Instructions

    1

    Place the two pieces of stainless steel flat on the welding table, with the sides that need to be welded resting 1/16 inch apart. Secure the pieces of stainless steel by clamping them to the welding table with self-locking clamps.

    2

    Turn on the ARC welder and adjust the amperage for the size thickness and type of stainless steel welding electrode you are going to use to weld the stainless steel.

    3

    Put on your safety glasses, welding helmet and heavy leather welding gloves. Clamp a stainless steel welding electrode in the stinger of the ARC welder and connect the ARC welders ground clamp to the welding table.

    4

    Align the welding electrode with the joint between the two pieces of stainless steel and lower your welding helmet.

    5

    Strike and lift the welding electrode on the stainless steel joint to start the ARC between the stainless steel pieces and the welding electrode.

    6

    Work the electrode over and down 1/8 inch, then back over the weld joint to weld the two pieces of stainless steel together.

    7

    Remove your welding helmet and tap the weld with the chipping hammer to remove the slag from the stainless steel weld.

    8

    Allow the weld joint to cool thoroughly before you handle the welded stainless steel--the weld joint will be hot and can cause severe burns.

Read More.. >

Friday, March 28, 2014

How to Repair Wiper Blades With Rubbing Alcohol

How to Repair Wiper Blades With Rubbing Alcohol

Continuous buildup of dust and debris such as dust, smoke and mineral deposits from rain water reduces the efficiency of the windshield wiper blades on your car. Poorly performing wiper blades create hazardous driving conditions when its raining, potentially leading to accidents or even death. Performing frequent wiper blade maintenance significantly improves the efficiency with which the wipers remove dust, debris and water from the windshield and saves the cost, frequency and hassle of purchasing and installing new windshield wiper blades.

Instructions

    1

    Pour 1 cup of rubbing alcohol into a measuring cup.

    2

    Soak 10 cotton balls in the alcohol until the cotton balls become saturated with alcohol.

    3

    Pull the windshield wipers away from the windshield to allow yourself easy access to the blades for cleaning.

    4
    Cotton balls soaked in alcohol allow for easy cleaning of wiper blades.
    Cotton balls soaked in alcohol allow for easy cleaning of wiper blades.

    Wipe one cotton ball along the entire length of the wiper blade. Discard each cotton ball after it is used. Repeat the process as many times as necessary until the liquid runs clear from the wiper blade.

    5
    Linen cloth cleans a windshield to a streak-free shine.
    Linen cloth cleans a windshield to a streak-free shine.

    Soak a soft linen cloth in a solution of 50 percent rubbing alcohol and 50 percent warm water. Wash the windshield surface from top to bottom to remove dust, dirt, oil and other grime from the windshield and improve the performance of the wipers.

Read More.. >

Thursday, February 20, 2014

How to Turn the Distributor on a 1985 Camaro 2 8 With a V 6 Engine

The distributor on the 1985 Chevrolet Camaro is the main component that the spark plugs receive their voltage from. The distributor also supplies the proper firing order to the spark plugs to keep the engine in time. The gears on the bottom of the distributor shaft are turned by the camshaft. As the camshaft turns the distributor shaft, the distributor shaft turns the rotor inside of the distributor cap. The rotor then turns inside of the distributor cap and supplies the spark plugs with the proper amount of voltage to keep the engine timed.

Instructions

    1

    Park the 1985 Chevrolet Camaro in a safe working area and open the hood. Shut the motor off and engage the parking brake.

    2

    Raise the hood and prop it in place. Locate the distributor cap near the back of the engine. All of the spark plug wires are attached to the top of the distributor cap.

    3

    Mark a straight line on the front side of the distributor cap with a marker. Also mark another straight line on the front side of the distributor cap base directly below the other line. This will help you remember the exact setting of the distributor before moving it.

    4

    Loosen the hold-down screws on the bottom side of the distributor with a Phillips-head screwdriver.

    5

    Grab the distributor with both hands and turn it clockwise to retract the timing. Turn the distributor counterclockwise to advance the timing. Be sure to make short turns when turning the distributor. Once the distributor is timed to your liking, screw the hold-down screws back down tight with the Phillips-head screwdriver.

Read More.. >

Wednesday, November 27, 2013

How to Move a Car With a Dead Starter

How to Move a Car With a Dead Starter

When you turn the key in your cars ignition and the car fails to start, you may begin seeing dollar signs. The cost of repairing your vehicle is an immediate concern, and the cost of towing the vehicle soon follows. If your vehicles starter has failed, you can eliminate the towing costs by safely moving the vehicle on your own. By following a few quick steps, you can tow the vehicle to the appropriate location with a simple tow strap.

Instructions

    1

    Ask a friend or family member with a heavy-duty truck capable of towing cargo to help move your car. Trucks and large sport utility vehicles are recommended.

    2

    Attach one end of the tow strap to the hooks or holes in the front frame of your car. Do not attach the straps to the bumper of the car as your bumper cannot handle the pull of the tow and may become damaged.

    3

    Attach the remaining end of the tow strap to the back of the truck or sport utility vehicle doing the towing. Loop or hook the strap on the towing hitch receiver on the vehicle, not the bumper.

    4

    Turn on the hazard lights in both vehicles to signal other drivers to slow down and maintain assured clear distance. Assign a person to drive the towed vehicle with the dead starter. Although the car cannot run, someone must steer the vehicle and apply the brakes when stopping.

    5

    Put the car being towed in "Neutral." Drive slowly and avoid busy roadways. Ensure that the lead vehicle allows turning and stopping time for the towed vehicle, to avoid a collision. Drive with caution and avoid slamming on the brakes, which may cause the strap to jerk loose (see Reference one).

Read More.. >

Thursday, November 21, 2013

Problems With 1998 Ford Expeditions

Problems With 1998 Ford Expeditions

The 1998 Ford Expedition was the second year of the Expedition model, which continues to release new full-size SUVs as of 2011. Registered owner complaints include engine problems, suspension and transmission problems, accessories issues and electrical problems, among other issues.

Engine Problems

    The most common problems registered on 1998 Ford Expeditions involve engine problems. As many as 5 out of 10 complaints detail that the spark plug blew out of or ruined the head. Other complaints claim that the engine burns oil, misfires, stalls at idle or shudders at idle.

Suspension Problems

    The second most common complaint among 1998 Ford Expedition owners is that the air suspension fails frequently. The problem is often identified by a "sagging" back end and a "bouncy" response while driving. The average mileage of this problem and repair cost were noted to be 142,429 and $338, respectively.

Transmission Problems

    Common transmission problems of the 1998 Expedition include misaligned shift indicators, slipping transmissions and an inability to go into park. ALLDATA indicates that there has been a safety recall (TSB 97S86).

Safety Recalls

    Since 1997 there have been seven safety recalls on parts associated with the 1998 Ford Expedition, which have included recalls on exterior lights, vehicle speed control mechanisms, wheel lugs and bolts, lights, and gear position indication mechanisms, and other items. If your SUV still contains a recalled part, check with your local dealer for replacement options.

Read More.. >

Sunday, November 3, 2013

How to Remove Burrs From a Stainless Steel Product With Files

How to Remove Burrs From a Stainless Steel Product With Files

The process of cutting and forming stainless steel creates sharp thin burrs on the edges of the metal. Removing the burr from the edges of a stainless steel part will eliminate painful cuts to people handling the material. A properly used file will remove a burr from stainless steel without leaving a jagged edge. Jagged edges form when the file binds against the edge of the stainless steel. This creates a serrated edge that destroys the edge of the metal and creates additional cut hazards when handling the material.

Instructions

    1

    Set the stainless steel product on a work table. Fold a towel in half and place it on top of the stainless steel with the edge of the towel 1 to 2 inches from the burred edge of the stainless steel.

    2

    Slide the top leg of a C-clamp over the towel covering the stainless steel and the bottom leg under the worktable edge. Turn the C-clamp handle clockwise to secure the metal to the work table.

    3

    Hold one face of a flat file on top of the burred stainless edge. Tilt the file 15 degrees from the stainless steel products top face.

    4

    Slide the file along the burred edge as you push the file slowly away from you. Continue along the burred edge until no visible burr remains. Release the C-clamp from the stainless product. Flip the product over. Replace the towel over the stainless steel. Position and tighten the C-clamp to hold the metal.

    5

    Slide the file along the stainless steel while aligned at a 15-degree angle to remove the remaining burr. Hold one face of the flat file perpendicular to the front edge of the stainless steel product. Slide the file along the front edge of the stainless steel to remove the last of the burr from the metal.

Read More.. >

Tuesday, October 29, 2013

Problems With the Horn on a PT Cruiser

The PT Cruiser is a model produced by Chrysler Corporation. It is a small multi-purpose vehicle and has been available since the year 2000. While popular, it has its share of mechanical problems.

Ever Honking Horn

    One issue with the horn involves the electronic key chain that opens and locks the door. Sometimes, after locking the car from the outside, the horn starts up and doesnt stop. This is as opposed to the gentle beep that tells you your car is safely locked. This problem is due to the key chain not working properly.

Hard to Find Horn Button

    Another issue involves the horn not working or only working when pressed on the steering wheel. Troubleshooters also often find that the horn will only work if it is hit with a lot of force in certain areas. This is cited as one of the more common problems with the 2006 model.

Dead Horn

    Some cases report the horn just giving out completely, even when the alarm sounds. This is because of the electrical connector becoming loose or detached. The relevant switch can be found inside the steering wheel.

Read More.. >

Monday, October 7, 2013

Problems with a 2006 Dodge Caravan

Problems with a 2006 Dodge Caravan

According to the Dodge Problems website, the 2006 Caravan had the fourth-worst model year in its tenure. It had 57 recalls that year, for issues as minor as exterior accessories and as serious as brakes. There were a number of other problems serious enough for recall.

Headlights

    In the summer of 2008, Eagle Eyes, the manufacturers of headlamps for the 2006 Dodge Caravan, recalled the 11,534 Dodge Caravans that bore the lights. The light emanating from the lamps was not bright enough to meet federal motor vehicle safety standards. According to Automall USA, such dimly lit headlamps could result in a crash.

Windshield: Visibility Issues

    On March 8, 2006, Daimler-Chrysler recalled 268,800 Dodge Caravans because of a weak windshield wiper motor armature shaft, according to Automall USA. The concern was that breakage could occur, resulting in the loss of wiper function, which can be dangerous during rainy or snowy conditions.

Air Bags

    According to Automall USA, on January 11, 2010, the Chrysler Corporation deemed the airbag sensors on 308,950 of its cars---including Dodge Caravans---to be weak. The automakers concern was that the sensors could break as a result of inclement weather, allowing water to enter the sensors. This, in turn, would cause the airbags not to deploy properly, resulting in serious injury or loss of life.

Rear and Side Windows

    On December 11, 2007, Chrysler recalled 1,657 of its 2006 Dodge Caravans because the glass that made up their rear and side windows failed a tempered glass breakage test. Breakage of the glass could result in serious injury to the driver and occupants, according to the Automall website.

Engine

    Another complaint that did not lead to a recall, but was an inconvenience for 2006 Dodge Caravan owners, was the tendency of the 3.3-liter water pump to fail on the van. As the MSN Autos website points out, this led to many financial problems for owners. According to MSN Autos, the costs the Dodge Caravan owner incurred included a $72 charge for parts, $112.50 for labor, as well as a $65 flat rate. However, these quotes excluded the time the mechanic spent diagnosing the problems of the vehicle, as well as sales tax.

Read More.. >

Friday, October 4, 2013

Repair Issues With a Ford Focus

Repair Issues With a Ford Focus

The Ford Focus is a car that has been available in the United States since the late 90s. Since then, owners have shared common issues with it, along with suitable fixes. Contact switches, fuel gauges, and brake pedals are all parts that have caused repair issues for Ford Focus drivers.

Contact Switch Repair

    Interior lights in the Ford Focus may fail to turn off although all doors have been closed. A faulty contact switch in the lock striker is the cause. To repair this issue, you can replace the lock striker with an upgraded one that possesses revised contact switches.

Fuel Gauge Repair

    Sometimes a Ford Focus will still give an empty fuel reading even though youve just pumped a full tank of gas. When this happens, a bad fuel pump module is often to blame. To fix this issue, you will have to replace the fuel level sender card assembly with a revised version.

Brake Pedal Repair

    Some Ford Focus drivers have had problems with hard braking at the outset of a drive. Youll need a revised brake booster vacuum hose, as this will correct the problem of reduced assistance from the brake booster. Youll also have to reprogram and reset the Powertrain Control Module.

Read More.. >