Thursday, April 17, 2014
How to Weld Stainless Steel With Stick Welder
Stick or ARC welding stainless steel requires the use of a welding rod that is compatible with the chemical makeup of the stainless steel you are welding. You can use a higher purity stainless steel welding rod for lower grade stainless steel, but not vice versa. For example, a 316L rod can weld 304-grade stainless steel, but you cannot produce a weld with structural integrity using a 309L rod to weld 316-grade stainless steel; this is due to crystalline structures that form in the weld joint.
Instructions
- 1
Place the two pieces of stainless steel flat on the welding table, with the sides that need to be welded resting 1/16 inch apart. Secure the pieces of stainless steel by clamping them to the welding table with self-locking clamps.
2Turn on the ARC welder and adjust the amperage for the size thickness and type of stainless steel welding electrode you are going to use to weld the stainless steel.
3Put on your safety glasses, welding helmet and heavy leather welding gloves. Clamp a stainless steel welding electrode in the stinger of the ARC welder and connect the ARC welders ground clamp to the welding table.
4Align the welding electrode with the joint between the two pieces of stainless steel and lower your welding helmet.
5Strike and lift the welding electrode on the stainless steel joint to start the ARC between the stainless steel pieces and the welding electrode.
6Work the electrode over and down 1/8 inch, then back over the weld joint to weld the two pieces of stainless steel together.
7Remove your welding helmet and tap the weld with the chipping hammer to remove the slag from the stainless steel weld.
8Allow the weld joint to cool thoroughly before you handle the welded stainless steel--the weld joint will be hot and can cause severe burns.
Sunday, November 3, 2013
How to Remove Burrs From a Stainless Steel Product With Files
The process of cutting and forming stainless steel creates sharp thin burrs on the edges of the metal. Removing the burr from the edges of a stainless steel part will eliminate painful cuts to people handling the material. A properly used file will remove a burr from stainless steel without leaving a jagged edge. Jagged edges form when the file binds against the edge of the stainless steel. This creates a serrated edge that destroys the edge of the metal and creates additional cut hazards when handling the material.
Instructions
- 1
Set the stainless steel product on a work table. Fold a towel in half and place it on top of the stainless steel with the edge of the towel 1 to 2 inches from the burred edge of the stainless steel.
2Slide the top leg of a C-clamp over the towel covering the stainless steel and the bottom leg under the worktable edge. Turn the C-clamp handle clockwise to secure the metal to the work table.
3Hold one face of a flat file on top of the burred stainless edge. Tilt the file 15 degrees from the stainless steel products top face.
4Slide the file along the burred edge as you push the file slowly away from you. Continue along the burred edge until no visible burr remains. Release the C-clamp from the stainless product. Flip the product over. Replace the towel over the stainless steel. Position and tighten the C-clamp to hold the metal.
5Slide the file along the stainless steel while aligned at a 15-degree angle to remove the remaining burr. Hold one face of the flat file perpendicular to the front edge of the stainless steel product. Slide the file along the front edge of the stainless steel to remove the last of the burr from the metal.
Thursday, September 26, 2013
How to Weld Steel Tube
Welding thin steel exhaust tubing requires patience and the correct equipment to get a sealed weld. The difficult part of welding thin walled steel tubing is maintaining your weld puddle without overheating the connection will result in the puddle melting through the tubing. With a properly set up MIG welder and a little practice, you easily create a sealed weld joint on the thin diameter steel tubing. MIG welders are widely available at rental stores or for purchase at your local welding supply retailer.
Instructions
- 1
Read the owners manual for the welding machine to determine how to change the feeder wheels over to accept the .023 welding wire.
2Spool the welder with the .023 solid welding wire after you switch the wire feeder wheels.
3Open and close the valve located on top of the bottle of shielding gas to clear dirt and debris from the threaded area.
4Turn the threads of the MIG welder gas regulator clockwise to attach the regulator to the bottle of shielding gas. Set the adjustable wrench to fit the regulator nut and lock the nut to seal the connection. Open the valve to send gas to the MIG welder.
5Turn on the welding machine and place the grounding clamp on a piece of metal.
6Point the tip of the MIG gun at the metal and depress the trigger of the MIG gun. Listen to the sound coming from the weld area between the MIG cup and the grounded piece of metal. Adjust the heat and wire speed settings until you hear a sound similar to eggs frying in a pan.
7Place the ends of two pieces of steel exhaust tubing tightly together and ground the steel tubing with the grounding clamp.
8Wearing your safety glasses, place the end of the MIG wire protruding from the tip of the MIG gun against the center of the weld joint and depress the MIG guns trigger for 1 second to create a tack weld. Roll the pipe, placing tack welds around the weld joint.
9Put on your welding helmet and welding gloves.
10Rest the wrist of the hand that you are holding the MIG gun with on a firm flat surface and grasp the tacked pieces of pipe with the other hand.
11Align the wire extending from the MIG gun with the weld joint, flick your head forward to lower your welding helmet, and depress the trigger of the MIG gun.
12Move the MIG 1/8th of an inch and stop to let the weld puddle build, when the weld puddle reaches around 1/8th of an inch tall, move the MIG gun another 1/8th of an inch. Continue the process, turning the pipe as needed to expose more weld joint until you weld around the entire weld joint and reach the spot where you began welding the joint of the steel tube.
13Allow the joint to cool thoroughly before you move the welded tubing.