Showing posts with label tube. Show all posts
Showing posts with label tube. Show all posts

Wednesday, February 12, 2014

Tire Tube Stem Specs

Tire Tube Stem Specs

There are three different kinds of tire tube stems: the Schrader, Presta and Dunlop valve stems. The Schrader valve is used on almost all automobile tires, the Presta is used on many road and mountain bikes and the Dunlop is a pneumatic valve used on bike tires in Japan and other countries that is somewhat out of date.

Schrader Valve Stems

    A Schrader valve is most often made of brass with a threaded end. For tires, the stems are usually of a standard size, with an external thread of 7.7 millimeters and an internal thread of 5.30 millimeters. If you press the internal pin of the tire stem with a tire gauge, you can measure the internal pressure of the tire. A spring in the Schrader valve ensures that it stays closed.

Presta Valve Stems

    Unlike Schrader valves, Presta valves have no spring, which makes them easier to pump. Presta valves are narrower than Schrader valves at 6 millimeters in diameter. A nut on the top of the valve allows air to flow in or out of the tire stem. After inflating the tire, you must screw the nut back on so air doesnt leak out.

Dunlop Valve Stems

    The bottom of the Dunlop (or Woods) valve starts out at about the diameter of the Schrader valve and then decreases in diameter to about the size of the more narrow Presta valve (6 millimeters). You let air out of the Dunlop or valve by unscrewing the top ring on the valve stem.

Read More.. >

Thursday, September 26, 2013

How to Weld Steel Tube

Welding thin steel exhaust tubing requires patience and the correct equipment to get a sealed weld. The difficult part of welding thin walled steel tubing is maintaining your weld puddle without overheating the connection will result in the puddle melting through the tubing. With a properly set up MIG welder and a little practice, you easily create a sealed weld joint on the thin diameter steel tubing. MIG welders are widely available at rental stores or for purchase at your local welding supply retailer.

Instructions

    1

    Read the owners manual for the welding machine to determine how to change the feeder wheels over to accept the .023 welding wire.

    2

    Spool the welder with the .023 solid welding wire after you switch the wire feeder wheels.

    3

    Open and close the valve located on top of the bottle of shielding gas to clear dirt and debris from the threaded area.

    4

    Turn the threads of the MIG welder gas regulator clockwise to attach the regulator to the bottle of shielding gas. Set the adjustable wrench to fit the regulator nut and lock the nut to seal the connection. Open the valve to send gas to the MIG welder.

    5

    Turn on the welding machine and place the grounding clamp on a piece of metal.

    6

    Point the tip of the MIG gun at the metal and depress the trigger of the MIG gun. Listen to the sound coming from the weld area between the MIG cup and the grounded piece of metal. Adjust the heat and wire speed settings until you hear a sound similar to eggs frying in a pan.

    7

    Place the ends of two pieces of steel exhaust tubing tightly together and ground the steel tubing with the grounding clamp.

    8

    Wearing your safety glasses, place the end of the MIG wire protruding from the tip of the MIG gun against the center of the weld joint and depress the MIG guns trigger for 1 second to create a tack weld. Roll the pipe, placing tack welds around the weld joint.

    9

    Put on your welding helmet and welding gloves.

    10

    Rest the wrist of the hand that you are holding the MIG gun with on a firm flat surface and grasp the tacked pieces of pipe with the other hand.

    11

    Align the wire extending from the MIG gun with the weld joint, flick your head forward to lower your welding helmet, and depress the trigger of the MIG gun.

    12

    Move the MIG 1/8th of an inch and stop to let the weld puddle build, when the weld puddle reaches around 1/8th of an inch tall, move the MIG gun another 1/8th of an inch. Continue the process, turning the pipe as needed to expose more weld joint until you weld around the entire weld joint and reach the spot where you began welding the joint of the steel tube.

    13

    Allow the joint to cool thoroughly before you move the welded tubing.

Read More.. >