Thursday, February 20, 2014
How to Turn the Distributor on a 1985 Camaro 2 8 With a V 6 Engine
The distributor on the 1985 Chevrolet Camaro is the main component that the spark plugs receive their voltage from. The distributor also supplies the proper firing order to the spark plugs to keep the engine in time. The gears on the bottom of the distributor shaft are turned by the camshaft. As the camshaft turns the distributor shaft, the distributor shaft turns the rotor inside of the distributor cap. The rotor then turns inside of the distributor cap and supplies the spark plugs with the proper amount of voltage to keep the engine timed.
Instructions
- 1
Park the 1985 Chevrolet Camaro in a safe working area and open the hood. Shut the motor off and engage the parking brake.
2Raise the hood and prop it in place. Locate the distributor cap near the back of the engine. All of the spark plug wires are attached to the top of the distributor cap.
3Mark a straight line on the front side of the distributor cap with a marker. Also mark another straight line on the front side of the distributor cap base directly below the other line. This will help you remember the exact setting of the distributor before moving it.
4Loosen the hold-down screws on the bottom side of the distributor with a Phillips-head screwdriver.
5Grab the distributor with both hands and turn it clockwise to retract the timing. Turn the distributor counterclockwise to advance the timing. Be sure to make short turns when turning the distributor. Once the distributor is timed to your liking, screw the hold-down screws back down tight with the Phillips-head screwdriver.
Tuesday, January 28, 2014
How Do I Replace an Oxygen Sensor in a 1985 Chevy S 10 Blazer
The single oxygen sensor on the 1985 Chevy S-10 Blazer is a more primitive design than todays O2 sensors. Its erred to as a non-heated single (one) wired sensor. While it functions similarly to todays sensors, it demands that the engine is up to operating temperature, including the engine coolant, before it begins to monitor the fuel-to-air ratio. Todays sensors have multiple wires with built-in heaters that heat them up quickly to begin monitoring the emissions more readily. This lessens the amount of pollutants allowed into the air while the vehicle is warming up.
Instructions
- 1
Apply the parking brake of the 1985 Chevy S-10 Blazer and then open the hood. Access to the oxygen sensor is on the lower side of the engine, but youll have more adequate lighting with the hood opened.
2Hoist one front quarter of the Blazer up with a jack placed under the frame rail and then lower the jack and Blazer onto a jack stand. Repeat for the other front quarter to elevate the front end completely.
3Put on the safety glasses and crawl underneath the Blazer with the remaining items.
4Follow the front exhaust pipe to where it connects to the manifold on the drivers side to locate the oxygen sensor.
5Follow the wire coming off the end of the oxygen sensor to the wire harness plug mating connection to the oxygen sensor plug. Lift up the release tab of the wire harness plug and then pull the oxygen sensor plug out.
6Put the oxygen sensor socket onto the ratchet and then align the wire of the sensor into the slit on the side of the socket.
7Place the socket fully onto the hex-head of the sensor and then turn the ratchet counterclockwise to remove it from the sensor exhaust port. Remove the sensor.
8Inspect the replacement oxygen sensor threads. If there is no anti-seize compound on the threads, apply a thin coating of electrically conductive anti-seize compound to the threads, being caul not to get the compound on the head of the sensor.
9Hand-thread the replacement sensor into the oxygen sensor exhaust port as far as it will go.
10Tighten the sensor snugly with the ratchet and oxygen sensor socket (placing the sensor wire into the socket slit), but do not over-tighten it. The threads of the sensors are made of much softer metal than the exhaust system to prevent damaging the mating threads of the system. Because of this, its easy to strip the threads of the sensors.
11Connect the sensor wire plug to the mating plug of the wire harness until the lock clicks into place.
12Lower the Blazer and close the hood.