Thursday, March 13, 2014
PT Cruiser Service Guide
Chrysler released the first PT Cruiser in 2000. Classified as a sedan with a rear hatch, the 2010 PT Cruiser was the last of this model. Owners benefit from following the prescribed maintenance schedule within the PT Cruiser owners manual or service guide by increasing the vehicles life.
Oil Changes
According the 2010 Chrysler PT Cruiser owners manual, change the oil and oil filter every 3,000 miles or every three months if you frequently drive off-road, use your vehicle for a delivery service, drive on heavily trafficked roads or in an environment with temperatures frequently above 90 degrees Fahrenheit. Change the oil and oil filter every 6,000 miles in normal conditions or conditions not listed above.
Monthly Checks
Each month check your tire pressure and tire wear. Check the oil and fluid levels indicated by the engine oil dipstick, coolant reservoir and brake master cylinder. Also, test the light bulbs on the interior and exterior of the vehicle work.
Replacing Filters and Spark Plugs
Replace the spark plugs, air cleaner filter and make-up filter when the odometer reaches 30,000 miles, 60,000 miles and then every 30,000 miles thereafter in normal driving conditions.
Friday, November 22, 2013
Chrysler Cruiser Fault Code P1494
The current industry standard for on-board diagnostics (OBD) codes is OBD-II. While Chrysler use OBD-II, they also use their own codes for specific problems. OBD-II codes start P0 followed by three digits. P1494 is a Chrysler-specific code.
Cruiser Codes
To read error codes on a Chrysler Cruiser, turn the key between the Run position (just before Start) and the off position three times within the space of five seconds. The odometer will show the codes.
Code P1494
Code P1494 gives the description Leak Detection Pump Switch or Mechanical Fault. Either the switch system for the leak detection pump, or the pump itself, is malfunctioning.
Significance
Cars have an evaporative (EVAP) system to stop fuel vapors being emitted to the atmosphere. The leak detection pump (LDP) is used to check that there are no leaks in the EVAP system. As the EVAP system is meant to be pressurized, it needs to be monitored for leaks, and so the LDP or switch needs fixing or replacing.
Tuesday, October 29, 2013
Problems With the Horn on a PT Cruiser
The PT Cruiser is a model produced by Chrysler Corporation. It is a small multi-purpose vehicle and has been available since the year 2000. While popular, it has its share of mechanical problems.
Ever Honking Horn
One issue with the horn involves the electronic key chain that opens and locks the door. Sometimes, after locking the car from the outside, the horn starts up and doesnt stop. This is as opposed to the gentle beep that tells you your car is safely locked. This problem is due to the key chain not working properly.
Hard to Find Horn Button
Another issue involves the horn not working or only working when pressed on the steering wheel. Troubleshooters also often find that the horn will only work if it is hit with a lot of force in certain areas. This is cited as one of the more common problems with the 2006 model.
Dead Horn
Some cases report the horn just giving out completely, even when the alarm sounds. This is because of the electrical connector becoming loose or detached. The relevant switch can be found inside the steering wheel.
Tuesday, October 22, 2013
How to Replace a Land Cruiser Oxygen Sensor
Your Toyota Land Cruiser monitors the oxygen levels in the exhaust using oxygen sensors. When an oxygen sensor fails, your truck begins to burn more fuel, running rich. Your gas mileage will decrease and the check engine light may come on. A Toyota Land Cruiser has as many as four oxygen sensors if it is equipped with dual exhaust. A single exhaust truck will have two sensors.
Instructions
- 1
Identify the sensor you need to replace. For trucks with single exhaust pipes, you will find the sensors in front of and behind the catalytic converter. If you have dual exhaust, you will have a set of two sensors on each exhaust pipe. Replace them all for ease of maintenance if you can. You can buy sensors at a Toyota dealer or auto parts specialty store.
2Pull the wiring harness from the top of the sensor. The wiring harness clips into place and will pull free easily.
3Remove the sensor from the exhaust pipe. You may find two retaining nuts securing it, or it may thread into the pipe. Use a closed-end wrench to remove the nuts if needed. Use an oxygen sensor socket and ratchet to remove the sensor if it threads into the pipe.
4Replace the sensor with a new one, threading it in by hand and then tightening it with the oxygen sensor socket and ratchet. If retaining nuts secure your sensor, replace them and tighten them with a closed-end wrench.
5Insert the wiring harness connector to the top of the oxygen sensor. Press the connector in until it is secure. Repeat the process on the remaining sensors.