Showing posts with label caravan. Show all posts
Showing posts with label caravan. Show all posts

Saturday, March 22, 2014

How to Install a Thermostat in a 2002 Grand Caravan

How to Install a Thermostat in a 2002 Grand Caravan

If the thermostat in the 2002 Dodge Grand Caravan malfunctions, the engine may not warm up properly and you may not be able to heat the cabin of the vehicle. This is annoying for the driver and passengers, especially if the thermostat fails in the winter. If the thermostat fails, replace the thermostat as quickly as possible to prevent extended use of the vehicle without proper engine heating.

Instructions

    1

    Drain two gallons of radiator fluid from the radiator via the petcock on the bottom of the radiator. You can reuse the fluid later so use a clean container.

    2

    Locate the thermostat by following the upper radiator hose from the radiator to the housing on the engine.

    3

    Pry the clamp off the hose with a pair of pliers. Pull the hose off the housing.

    4

    Remove the bolts that secure the housing to the Caravans engine with a socket and ratchet. Pull the housing off the engine.

    5

    Pull the thermostat out of the engine. Remove and discard the thermostat gasket.

    6

    Clean the surface of the thermostat housing and the engine with a clean towel.

    7

    Install the new gasket. Put the new thermostat into the hole.

    8

    Place the thermostat housing on top of the gasket. Thread the bolts into the housing with your fingers. Tighten the bolts with the socket and ratchet.

    9

    Slide the hose onto the housing. Secure the hose with the clamp.

    10

    Pour the radiator fluid back into the radiator.

Read More.. >

Sunday, March 16, 2014

How to Change the Tensioner Pully on a 94 Dodge Caravan

The tensioner pulley on a 1994 Dodge Caravan serpentine belt tensioner assembly allows the transference of tension from the tensioner to the belt. The pulley itself has an internal bearing ring so it can rotate freely at the end of the serpentine belt tensioner arm. If the bearing ring gives out, the pulley will either wobble or seize, neither of which is conducive to continued serpentine drive system operation. Unfortunately, the pulley itself is not serviceable. However, Dodge does offer the entire tensioner assembly. Anyone with good mechanical aptitude can change a Caravan tensioner in about an hour.

Instructions

    1

    Lift the Caravans hood and support it with the prop rod. Examine the belt routing diagram sticker, placed on the fan shroud or underside of the hood, to verify the location of the belt tensioner on your specific Caravan.

    2

    Rotate the Caravans serpentine belt tensioner assembly clockwise to relieve the tension on the belt. Slip the belt off the tensioner with your free hand before rotating the tensioner back to its home position. Remove the tool.

    3

    Extract the two mounting bolts that hold the serpentine belt tensioner assembly to the Caravans front engine cover using your socket set. Depending on your physical size and dexterity, you may find this easier to accomplish through the top of the engine well or through the passenger-side wheel well.

    4

    Pull the old serpentine belt tensioner assembly out of the Caravans engine bay by hand. Place the new serpentine belt tensioner assembly on the Caravans front engine cover and bolt it in using your socket set.

    5

    Rotate the new serpentine belt tensioner assembly clockwise with the serpentine belt tool and then place the belt on the pulley by hand. Rotate the new serpentine belt tensioner assembly back into place. Remove the tool and close the hood.

Read More.. >

Monday, December 9, 2013

How to Change the Timing Chain on a 2001 Caravan

The Caravan is a minivan that Chrysler Group sells under its Dodge brand. Chrysler introduced the Caravan in 1984, and the the 2001 model belongs to the fourth generation of this series. The 2001 Dodge Caravan is available with six-cylinder engines that require timing chains. These engines have a single overhead camshaft, and a displacement of 3.3 or 3.8 liters. The timing chain does not wear out and should only require replacement if it breaks.

Instructions

    1

    Drain the coolant from the radiator into a drain pan. Drain the oil from the crankcase into a separate drain pan. Disconnect the cable from the negative battery terminal with a socket wrench. Raise and support the vehicle on jack stands. Remove the right wheel and splash shield under the engine with a socket wrench.

    2

    Detach the oil pick up tube from the oil pan and disconnect the oil pan. Remove the drive belt from the air compressor and disconnect the damper from the crankshaft. Detach the lower hose from the radiator and remove the heater hose from the cover of the timing chain.

    3

    Disconnect the engine mount and its bracket from the right side of the engine with a socket wrench. Remove the water pump and power steering support bolt from the timing chain cover. Disconnect the mounting bolts from the timing chain cover and detach the cover. Discard the gasket for the timing chain cover.

    4

    Turn the crankshaft clockwise to align the timing mark on the crankshaft sprocket with the colored link on the timing chain. Disconnect the attaching bolt for the camshaft sprocket with a socket wrench. Remove the timing chain and the camshaft sprocket. Disconnect the crankshaft sprocket from the crankshaft with special tools 5048-1, 5048-6 and 8539.

    5

    Turn the crankshaft clockwise until its timing arrow points straight up. Lubricate the new timing chain and the sprockets with engine oil. Place the timing chain onto the camshaft sprocket so that the plated link aligns with the dot on the camshaft sprocket.

    6

    Put the timing chain around the crankshaft sprocket so that the other plated link on the timing chain aligns with the dot on the crankshaft sprocket. Position the camshaft so that its timing arrow points straight down and install the camshaft sprocket onto the camshaft. Tighten the bolt on the camshaft sprocket 40 ft. lbs. with a torque wrench.

    7

    Install the crankshaft sprocket on the the crankshaft with a socket wrench. Turn the crankshaft two full turns and align its timing marks once again.

    8

    Clean the mating surfaces n the timing chain with a shop towel. Install a new gasket onto the timing chain cover so the edge of the gasket is 0.02 in. past the edge of the cover. Turn the crankshaft clockwise until the flats of the oil pump drive are vertical. Install the oil pump to the crankshaft so that the flats of the oil pump rotor align with the flats of the crankshaft.

    9

    Replace the timing chain cover and fasten its mounting bolts with a socket wrench. Tighten the 8mm bolts to 20 ft. lbs. and tighten the 10mm bolts to 40 ft. lbs. with a torque wrench. Install the water pump and bolt for the power steering support to the timing chain cover. Replace the damper to the crankshaft.

    10

    Install the bracket for the engine mount. bracket with a socket wrench. Tighten the 10mm bolts to 40 ft. lbs. and tighten the 8mm bolts to 21 ft. lbs. with a torque wrench. Install the remaining components by performing steps one and two in reverse order. Fill the radiator with fresh coolant, and fill the engine with new oil. Start the engine and correct any fluid leaks.

Read More.. >

Thursday, November 14, 2013

How to Replace the Accessory Belt on a Dodge Grand Caravan

The engine accessories on the Dodge Grand Caravan are controlled by a single wide accessory belt that travels around each accessory pulley at the same time. The belt is designed in a manner that makes it possible for the single belt to control all of the accessories at the same exact time. As the belt turns around each accessory pulley, each accessory performs its designated operation. The excessive turning of the belt around the pulleys can cause fraying and cracking. Replace the belt as soon as any damage to the belt is visible.

Instructions

    1

    Inspect the top center portion of the plastic radiator guard for the diagram that explains the routing instructions for the single accessory belt, also known as a serpentine belt.

    2

    Inspect the front of the motor and find the belt tensioner device that is keeping the belt tight inside of the accessory pulleys. Use the bolt that connects the pulley to the end of the tensioner arm to release the tension from the accessory belt.

    3

    Pivot the belt tensioner device counterclockwise with a breaker bar and a socket. Pull the belt out from under the tensioner pulley. Slowly release the tension from the breaker bar until the tensioner device stops moving.

    4

    Unwrap the belt from each accessory pulley. Slide the belt around the fan blades, and out of the engine well. Match the new and old belt together to ensure the correct size of the new belt.

    5

    Maneuver the belt around each of the fan blades and around each accessory pulley by following the routing directions exactly as described from the belt routing diagram.

    6

    Pivot the tensioner device counterclockwise with the breaker bar and socket. Pull the belt around the tensioner pulley, and release the tension from the breaker bar. As the tensioner pulley is springing back against the belt, the tensioner device will tighten the belt to the proper tension. Take the breaker bar off of the tensioner, and remove it from the engine well.

    7

    Crank the engine, and let it to run for about 20 seconds or so. This will finish seating the ribs of the belt to the inside of the accessory pulley grooves. Shut the engine off.

Read More.. >

Thursday, October 17, 2013

How to Install a Timing Belt on a 1990 Dodge Caravan 2 5

The Dodge Caravan is a family minivan that Chrysler Group has sold under its Dodge brand since 1984. One of the engines available for the 1990 model is a four-cylinder 2.5-liter motor with a single overhead camshaft. This type of engine uses a timing belt to connect the crankshaft and camshaft, allowing the cylinder valves to open and close at the correct time. The timing belt requires replacement at regular intervals, and typically lasts at least 60,000 miles.

Instructions

    1

    Disconnect the compressor bracket for the right engine mount with a socket wrench and detach the engine mount. Remove the accessory drive belts and the cover for the timing belt. Place a floor jack under the engine and raise the engine slightly. Remove the tensioner screw on the timing belt and disconnect the timing belt.

    2

    Rotate the crankshaft and intermediate shaft to align the timing marks on the their respective sprockets. Turn the camshaft to align the timing mark on the camshaft hub with the line on the cylinder head.

    3

    Place the new timing belt over the sprockets of the crankshaft and intermediate drive shaft. Turn the hex nut on the timing belt tensioner with a hex wrench to adjust the tension on the timing belt. The timing belt is at the correct tension when you can twist the timing belt to a right angle with your thumb and forefinger.

    4

    Turn the crankshaft two full turns clockwise and align its timing marks. Tighten the locking nut on the timing belt tensioner to 45 foot-pounds. with a torque wrench.

    5

    Lower the engine with the floor jack and replace the timing belt cover with a socket wrench. Connect the accessory drive belts and adjust their tension. Attach the engine mount and fasten the compressor bracket to the engine mount.

Read More.. >

Monday, October 7, 2013

Problems with a 2006 Dodge Caravan

Problems with a 2006 Dodge Caravan

According to the Dodge Problems website, the 2006 Caravan had the fourth-worst model year in its tenure. It had 57 recalls that year, for issues as minor as exterior accessories and as serious as brakes. There were a number of other problems serious enough for recall.

Headlights

    In the summer of 2008, Eagle Eyes, the manufacturers of headlamps for the 2006 Dodge Caravan, recalled the 11,534 Dodge Caravans that bore the lights. The light emanating from the lamps was not bright enough to meet federal motor vehicle safety standards. According to Automall USA, such dimly lit headlamps could result in a crash.

Windshield: Visibility Issues

    On March 8, 2006, Daimler-Chrysler recalled 268,800 Dodge Caravans because of a weak windshield wiper motor armature shaft, according to Automall USA. The concern was that breakage could occur, resulting in the loss of wiper function, which can be dangerous during rainy or snowy conditions.

Air Bags

    According to Automall USA, on January 11, 2010, the Chrysler Corporation deemed the airbag sensors on 308,950 of its cars---including Dodge Caravans---to be weak. The automakers concern was that the sensors could break as a result of inclement weather, allowing water to enter the sensors. This, in turn, would cause the airbags not to deploy properly, resulting in serious injury or loss of life.

Rear and Side Windows

    On December 11, 2007, Chrysler recalled 1,657 of its 2006 Dodge Caravans because the glass that made up their rear and side windows failed a tempered glass breakage test. Breakage of the glass could result in serious injury to the driver and occupants, according to the Automall website.

Engine

    Another complaint that did not lead to a recall, but was an inconvenience for 2006 Dodge Caravan owners, was the tendency of the 3.3-liter water pump to fail on the van. As the MSN Autos website points out, this led to many financial problems for owners. According to MSN Autos, the costs the Dodge Caravan owner incurred included a $72 charge for parts, $112.50 for labor, as well as a $65 flat rate. However, these quotes excluded the time the mechanic spent diagnosing the problems of the vehicle, as well as sales tax.

Read More.. >