Friday, June 6, 2014
How to Turn Off the Seat Belt Warning on a Toyota Camry
Newer Toyota Camrys are equipped with a bell that warns you to put on your seat belt before starting the car. Some people find it annoying and wish to turn off the chiming. There are instructions in the owners manual on how to do this. You dont need any special tools to turn off this seat belt warning and it will only take a few moments of your time.
Instructions
- 1
Put the key into the ignition and turn it to the on position, but do not start the engine.
2Look for a tiny knob on the instrument panel and press it to toggle between the odometer reading and the trip odometer reading. Keep pressing the knob until you see "ODO." Turn off the vehicle.
3Turn the ignition on but dont crank the engine. Pull the tiny knob out for 10 seconds. While still holding the knob out, put on your seat belt and keep holding the knob for another 5 seconds then release it. The instrument panel will now read "B off."
4Repeat the above procedure to turn the seat belt warning chime back on.
Thursday, May 22, 2014
How to Measure a V Belt Length
V-belts have a cross section resembling a "V." The narrow end of the "V" taper sits inside the groove of a taper wheel. This increases the contact area between the pulley and the belt. During use the belt stretches and will eventually break. Installing a correctly sized replacement belt between the pulleys will ensure the belt sits under proper tension. A simple method for determining the length of a V-belt exists that allows you to avoid using a complex mathematical formula.
Instructions
- 1
Wipe the inside groove of the pulleys clean with a rag.
2Pull a length of 1/8-inch diameter twine around the two pulleys to be connected by the V-belt. Pull the twine tight. Ensure the ends of the twine overlap by 4 inches.
3Draw a line across the overlapped twine with a permanent marker. Make sure the line is visible on both pieces of twine. Remove the twine from the pulleys.
4Set the marked twine flat on a firm surface. Hold one end of the twine on the end of a tape measure. Pull the twine taught while it sits next to the tape measure. Read the dimension where the second mark on the twine falls on the tape measure to determine the length of the V-belt.
Saturday, May 17, 2014
How to Install a Timing Belt for a 2000 Ford Focus
The Ford Focus is a compact car that Ford began manufacturing for the 2000 model year in North America. The engine for a Ford Focus made before 2005 is a four-cylinder 2.0-liter engine with a double overhead camshaft. This type of engine uses a timing belt instead of a timing chain, and requires you to replace the timing belt at regular intervals. The timing belt for a 2000 Ford Focus allows the crankshaft to turn the camshaft.
Instructions
- 1
Remove the cable from the negative battery terminal with a socket wrench to prevent you from inadvertently starting the engine. Disconnect the accessory drive belt and its tensioner. Remove the cover for the timing belt.
2Loosen the lug nuts for the right front wheel with a lug wrench. Raise the vehicle and support it on jack stands. Remove the right front wheel and the right splash shield with a socket wrench. Disconnect the pulley for the crankshaft.
3Turn the timing belt clockwise so that the timing marks on the camshaft and crankshaft sprockets align with their respective marks on the engine.
4Loosen the bolt for the timing belt tensioner with a socket wrench. Turn the tensioner 1/4 turn counterclockwise with an 8mm Allen wrench. Place a 1/8 in. drill bit into the hole of the timing belt tensioner to hold the tensioner in place. Remove the timing belt from the camshaft sprocket and crankshaft sprocket.
5Place the new timing belt on the crankshaft. Complete the timing belt installation by proceeding in a counterclockwise direction. Remove the drill bit from the timing belt tensioner hole to release the tensioner.
6Turn the crankshaft clockwise by two complete turns to align the timing marks once again. Tighten the bolt for the timing belt tensioner to between 15 and 22 pounds with a torque wrench.
7Connect the crankshaft pulley and tighten its mounting bolt to between 81 and 96 ft. lbs. with a torque wrench. Connect the right splash shield and right front wheel with a socket wrench.
8Lower the vehicle and tighten the lug nuts with a lug wrench. Install the accessory drive belt and its tensioner with a socket wrench. Attach the cable to the negative battery terminal.
Friday, May 16, 2014
How to Replace the Timing Belt on a 2003 Ford Focus
Ford started production of the Ford Focus in 1999. The models made from 1999 to 2007 were the first generation of this series. The standard engine in the 2003 Focus has four cylinders and a displacement of 2.0 liters. The timing belt on this vehicle synchronizes the movements between the crankshaft and the camshaft. The tension on the timing belt is a critical factor in its installation.
Instructions
- 1
Open the hood. Disconnect the negative battery terminal with socket wrench. Turn the drive belt tensioner clockwise to reduce the tension on the accessory drive belt. Remove the drive belt. Disconnect the tensioner with a socket wrench. Remove the timing belt cover.
2Raise and support the vehicle on jack stands. Remove the right front wheel with a lug wrench and disconnect the right splash shield. Remove the pulley for the crankshaft.
3Turn the crankshaft clockwise to align the timing marks on the crankshaft and camshaft sprockets. Loosen the tensioner bolt on the timing belt with a socket wrench. Turn the tensioner counterclockwise by 1/4 turn with an 8mm Allen wrench. Place a 1/8-inch drill bit into the hole on the timing belt tensioner to hold the belt tensioner in place. Remove the timing belt.
4Install the new timing belt onto the crankshaft by proceeding in a counterclockwise direction. Remove the drill bit from the hole in the timing belt tensioner. Turn the crankshaft clockwise by two turns so that the timing marks align once again. Torque the tensioner bolt for the timing belt to between 15 and 22 foot-pounds with a torque wrench.
5Install the crankshaft pulley with a socket wrench and tighten its mounting bolt to between 81 and 96 foot-pounds. Connect the right splash shield and the right front wheel. Lower the vehicle and replace the timing belt cover. Install the accessory drive belt tensioner and mount the drive belt. Attach the cable to the negative battery terminal.
Monday, April 21, 2014
1992 Plymouth Neon Timing Belt Installation
Neon was first introduced in North America in the early 90s. It is a front-wheel drive compact car that was manufactured by Chrysler Corporations Plymouth and Dodge Brands. It was powered by an inline 4 cylinder 2.0L engine that had an output of 132 horsepower and 130 foot-pounds of torque. It is a small and reliable engine, but it still need periodic service if parts like the timing belt fail.
Instructions
- 1
Disconnect the negative cable of your battery before performing any maintenance work on your engine, to prevent electrical shock or accidental starting. Remove the nut from the negative post with a box-end wrench. Lift the cable from your battery, move it outside of the battery box and close the lid of the battery box.
2Align the sprocket with the arrow on the oil pump housing and then set the crankshaft sprocket to the top dead center (TDC) position. Using a suitable wrench, move crankshaft to 1/2 notch before top dead center.
3Place the camshaft timing marks by aligning the notches on sprockets. Install timing belt, starting at crankshaft, around water pump sprocket, idler pulley, camshaft pulleys and tensioner pulley. Move the crankshaft sprocket to TDC to take up belt slack.
4Install belt tensioner to engine block but do not tighten fasteners. Using a suitable torque wrench on the tensioner pulley, torque the pulley to 28 foot-pounds. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and torque fasteners to 23 foot-pounds.
5Pull the tensioner plunger pin. Pretension is proper when pin can be easily removed or installed. Rotate crankshaft two revolutions and inspect the alignment of the timing marks. If the alignment is improper, repeat the operation.
Sunday, April 20, 2014
How do I Replace a Timing Belt on a 2000 Hyundai Elantra
The Hyundai Elantra is a series of compact cars that Hyundai has manufactured since 1990. The 2000 model represents the last year of the second generation Hyundai, which had a 4-cylinder, 2.0-liter engine as its standard engine. This engine uses a timing belt to synchronize the movement of the camshaft and crankshaft as opposed to a timing chain. The timing belt in a 2000 Hyundai requires replacement approximately every 60,000 miles.
Instructions
- 1
Disconnect any components necessary to access the cover of the timing belt. Remove the timing belt cover with a socket wrench.
2Turn the crankshaft clockwise to position the No. 1 piston at the top dead center position as indicated by the timing marks on the crankshaft. Disconnect the tensioner for the timing belt and the idler pulley with a socket wrench. Remove the timing belt from the camshaft sprocket and the crankshaft sprocket.
3Turn the camshaft sprocket clockwise to align its timing marks and ensure the timing marks for the crankshaft timing are still aligned. Connect the tensioner for the timing belt with a socket wrench, but do not tighten the pulley bolt for the tensioner. Install the idler pulley and tighten its mounting bolt to between 32 and 41 foot-pounds.
4Place the timing belt over the sprocket of the camshaft, then over the sprocket of the crankshaft. Turn the timing belt tensioner counterclockwise to place tension on the timing belt. Apply 5 pounds of force to the middle of the longest span of the timing belt. The deflection of the timing belt will be between 0.16 inches and 0.24 inches when the timing belt is at the correct tension.
5Tighten the pulley bolt for the timing belt tensioner to between 32 and 41 foot-pounds with a torque wrench. Turn the crankshaft sprocket clockwise by one turn to align the timing marks on the crankshaft sprocket. Adjust the timing belt tension as required.
6Replace the cover for the timing belt. Install any additional components that you removed in step one to access the timing belt.
Sunday, March 23, 2014
How to Replace the Timing Belt on a 2005 KIA Spectra
The Kia Spectra is a compact car produced from 2000 to 2009. The second generation of this series includes the 2004 through 2009 models, and represents a major redesign over the first generation Kia. The only engine available for the 2005 Kia in North American is a four-cylinder 2.0-liter engine with a double overhead camshaft. This design uses a timing belt to drive the camshafts with the crankshaft. The most important part of replacing the timing belt is keeping the crankshaft and camshafts in the correct position during the procedure.
Instructions
- 1
Disconnect the cable from the negative battery terminal with a socket wrench to ensure you dont inadvertently start the engine. Raise the vehicle and support it on jack stands. Remove the engine cover, right wheel and side cover for the right wheel. Detach the accessory drive belts, water pump pulley and upper cover for the timing belt.
2Turn the crankshaft pulley clockwise to align the groove on the pulley with the timing mark on the lower timing belt cover. Disconnect the pulley and flange for the crankshaft with a socket wrench. Remove the lower timing belt cover and timing belt tensioner. Detach the timing belt from the pulleys.
3Turn the crankshaft clockwise to align the timing marks for the crankshaft and camshaft. Install the timing belt tensioner with a socket wrench. Place the new timing belt onto the crankshaft sprocket, idler pulley, camshaft sprockets and timing belt tensioner in that order.
4Turn the timing belt tensioner clockwise to apply tension to the timing belt. Press the tension side of the timing belt with moderate force. The tension is correct when the deflection of the timing belt is about 0.2 in. Tighten the mounting bolts for the tensioner to 20 ft. lbs. with a torque wrench. Turn the crankshaft clockwise by two full turns and align the timing marks once again.
5Attach the lower timing belt cover and tighten its mounting bolts to between six and seven ft. lbs. with a torque wrench. Connect the flange and pulley for the crankshaft. Tighten the bolt for the crankshaft pulley to between 123 and 130 ft. lbs. Connect the upper timing belt cover and tighten the mounting bolts to between six and seven ft. lbs.
6Install the water pump pulley and accessory drive belts with a socket wrench. Attach the right wheel and side cover for the right wheel. Replace the engine cover and connect the cable to the negative battery terminal with a socket wrench.
Thursday, March 20, 2014
How to Install a Timing Belt on a 2002 KIA Rio Cinco
The Kia Rio is a subcompact car that Kia Motors has produced since 2001. The Cinco trim level of the Rio is a five-door hatchback available in the United States. The procedure for installing the timing belt depends only on the engine and is not directly affected by the trim level. The 2002 Kia Rio Cinco has a four-cylinder, 1.5-liter engine that uses a timing belt to synchronize the movements of the camshaft and crankshaft.
Instructions
- 1
Remove the cable from the negative terminal of the battery with a socket wrench. Detach the accessory drive belts from their respective pulleys. Disconnect the alternator and water pump.
2Disconnect the crankshaft pulley with a socket wrench and remove the guide plate from the timing belt pulley. Disconnect the upper and lower covers for the timing belt.
3Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing mark on the engine. The I and E marks on the camshaft pulley must also align with their respective marks on the cylinder head. Disconnect the timing belt tensioner pulley and the timing belt with a socket wrench.
4Connect the pulley for the timing belt tensioner. Pull the tensioner away from the crankshaft pulley as far as possible and fasten the lock bolt for the tensioner to hold it in place. Place the timing belt onto the crankshaft pulley, idler pulley, exhaust camshaft pulley, intake camshaft pulley and tensioner pulley, in that order.
5Loosen the pulley for the timing belt tensioner to apply tension to the timing belt. Tighten the lock bolt to between 28 and 38 foot-pounds with a torque wrench. Turn the crankshaft clockwise by two full turns and align the timing marks.
6Install the upper and lower covers for the timing belt with a socket wrench. Tighten the mounting bolt for the crankshaft pulley to between 9 and 13 foot-pounds with a torque wrench. Connect the water pump pulley and tighten its mounting bolt to between 9 and 13 foot-pounds.
7Install the alternator and attach the accessory drive belts. Connect the cable to the negative terminal of the battery.
Wednesday, February 19, 2014
How to Change the Timing Belt on a 2001 Four Cylinder Honda Accord
The Honda Accord is a mid-size car that has been in production since 1976. The 2001 model belongs to the sixth generation of this series, which includes Accords made from 1998 to 2002. The 2001 Honda Accord typically has a four-cylinder 2.3-liter engine with multi-point fuel injection. This engine uses a timing belt to keep the camshaft synchronized with the crankshaft. The procedure for replacing the timing belt requires you to set the crankshaft to the top dead center (TDC) position several times.
Instructions
- 1
Disconnect the valve cover and upper covers for the timing belt with a socket wrench. Remove any additional components needed to access the crankshaft. Turn the crankshaft clockwise by hand to align the white mark on the crankshaft sprocket with the pointer on the lower cover of for the timing belt. The word "UP" on the camshaft sprocket must also be in the 12 oclock position.
2Remove the lower timing belt cover with a socket wrench. Fasten one of the mounting bolts for the lower timing cover to the adjuster arm of the timing belt tensioner. This will hold the timing belt adjuster in position.
3Loosen the lock bolt and adjusting nut on the timing belt tensioner with a socket wrench, and push the tensioner away from the timing belt to relieve the tension on the timing belt. Tighten the adjuster nut on the timing belt, and pull the timing belt off its sprockets.
4Turn the crankshaft clockwise by hand to align the pointer on the crankshaft sprocket with the pointer on the oil pump. The word "UP" on the camshaft sprocket must also be in the 12 oclock position.
5Mount the new timing belt to the crankshaft sprocket, timing belt tensioner sprocket, water pump sprocket and camshaft sprocket in that order. Loosen the adjusting nut on the timing belt tensioner with a socket wrench, then tighten it again to apply tension to the timing belt.
6Install the lower timing belt cover with a socket wrench, and rotate the crankshaft sprocket five to six complete turns clockwise to seat the timing belt on the sprockets. Make sure the timing mark on the crankshaft sprocket aligns with the timing mark on the lower timing cover. The word "UP" on the camshaft sprocket must also be in the 12 oclock position.
7Turn the adjusting nut on the timing belt tensioner counterclockwise by one turn. Turn the crankshaft counterclockwise to move the camshaft sprocket back by three teeth, and tighten the adjusting nut on the timing belt. Turn the crankshaft clockwise to align the timing marks once again.
8Install the upper timing belt cover with a socket wrench. Connect all additional components you removed to access the crankshaft. Replace the valve cover.
Sunday, February 16, 2014
How to Use a Tensioner on an Alternator Belt
A belt tensioner is a spring-loaded device on some engines that holds a specific amount of tension on the serpentine drive belt or accessory belt while the engine is in motion. Too much tension on the belt can stretch it, causing the belt to weaken, while too little tension can cause the belt to squeak and whine. The belt tensioner makes it relatively easy to remove the belt from your vehicle if you need to perform maintenance on any of the components the belt drives, such as the alternator.
Instructions
- 1
Open the hood of your vehicle and locate the alternator and the belt that drives the alternator. Find the belt tensioner for the alternator belt.
2Place the box-end of a wrench around the bolt on the belt tensioner. Choose a wrench that properly fits the bolts so it does not slip.
3Pull the wrench counterclockwise to draw back the belt tensioner (compressing the spring) arm and release tension on the belt. Continue holding the belt tensioner and remove the belt.
4Turn the belt tensioner clockwise slowly to return to its normal position (allowing the spring to relax).
5Pull the belt tensioner arm counterclockwise to reinstall the belt. Route the belt along the pulleys following the belt-routing diagram for your vehicle. Check under your hood for the belt-routing diagram; consult your service manual if you are not able to find it.
6Turn the belt tensioner clockwise slowly, with the belt rerouted along the appropriate path, allowing the tensioner arm to draw the belt taut.
Tuesday, February 11, 2014
The Removal of a Belt Driven Fan on a 1999 Dodge Dakota
Removing the mechanical fan from the front of the engine in your Dodge Dakota requires a specific wrench. The spanner wrench is available from tool dealers and through the Dodge dealerships parts department, though it can be expensive. Many auto parts stores rent these wrenches as well as stocking a new fan assembly for your Dakota. The fan assembly threads onto the water pump hub, and does not require removal of the drive belt to remove.
Instructions
- 1
Open the hood and locate the negative battery cable. Follow it to the battery and remove the retaining bolt securing the cable end to the battery terminal with a wrench. Lift the cable off the battery and set it aside.
2Locate the bolts on the top section of the radiator shroud that secure the upper and lower halves. Remove the bolts with a socket and ratchet, then lift the top section of the shroud off the bottom section and remove it from the engine compartment.
3Place a spanner wrench with a pin adapter on it between the fan and water pump hub. There are four holes in the face of the water pump hub. Slide the two pins on the spanner into two of these holes.
4Grasp the fan blade with the opposite hand and spin the blades clockwise while holding the water pump hub with the spanner. The threads are right-handed, so turning it clockwise will loosen the blades.
5Caully lift the fan assembly out of the engine compartment and store it in an upright position so the silicone gel inside does not leak out. Remove the spanner from the engine compartment.
Saturday, January 25, 2014
How to Change the AC Belt on a Silverado
The serpentine belt in the Chevy Silverado works hard. The serpentine belt that controls the air conditioner also controls the other accessories in your vehicle. It is called a serpentine belt because of the way it snakes around inside the engine. It should be inspected each time you change the oil. Look for cuts, cracks or glazing. If it makes noise, it should be replaced. (Reference 1)
Instructions
- 1
Study the belts routing. If there is no diagram under the hood that shows the routing, draw one yourself. If the new belt is placed on the wrong way it will cause problems. (Reference 2)
2Unload the tensioner pulley using a 3/8 inch extension and ratchet. Attach the ratchet to the tensioner bolt and turn it counterclockwise.
3Caully remove the belt by first releasing it from the tensioner, then side the tensioner back into place, and remove the belt from the other pulleys.
4Check and clean the tensioner pulley and all the other pulleys for possible wear, dirt, old rubber or oil. Clean the grooves in the pulleys with a wire brush or brake cleaner.
5Install the replacement belt around all the pulleys, except the tensioner pulley, erring to your notes to be certain you are installing it in the correct direction.
6Turn the tensioner pulley to the left with the 3/8 inch ratchet, and slip the belt over it. Restore the tensioner to its original position.
7Start the engine and run it for about two minutes to allow the belt to become completely seated.
Friday, November 15, 2013
How to Use a Motorcycle Belt Adjustment Tool
Motorcycle belt adjustment tools are designed to adjust the tension and alignment on your motorcycle belts. Performing this adjustment yourself can help you better understand the mechanics of your motorcycle and help you troubleshoot any problems that arise with the belts on your motorcycle. Adjustment is easier if you are accustomed to using a belt adjustment tool.
Instructions
- 1
Stand your motorcycle in an upright position with a kickstand and four concrete blocks. Secure its position with the blocks on both sides of the front tire so that the motorcycle does not rock back and forth while you are working on it.
2Place the transmission into neutral and elevate the rear tire by placing a concrete block or jack under the rear suspension. You will need the rear tire to be able to spin freely to check the belt tension.
3Rotate the rear tire and measure the tight spots of the belt. Note the deflection of the belt as you rotate the rear tire in four places. Measure the deflection with a tape measure or a ruler approximately half the distance between the front and rear sprockets on the lower part of the belt. Note the tightest point on the belt and mark this area with your silver permanent marker.
4Adjust the wheel alignment if the left and right notches are not at the same marks or position of the swing arm. Be sure to do this before adjusting your belt.
5Use the tension gauge to push up the belt in the center from underneath, using 10 pounds of pressure (indicated on the tool), with maximum deflection of 1.5 mm to 4 mm at the front of the swing arm cross pipe. Repeat at the areas that you marked with the silver marker. Adjust your belt as needed for your motorcycles specifications
Thursday, November 14, 2013
How to Replace the Accessory Belt on a Dodge Grand Caravan
The engine accessories on the Dodge Grand Caravan are controlled by a single wide accessory belt that travels around each accessory pulley at the same time. The belt is designed in a manner that makes it possible for the single belt to control all of the accessories at the same exact time. As the belt turns around each accessory pulley, each accessory performs its designated operation. The excessive turning of the belt around the pulleys can cause fraying and cracking. Replace the belt as soon as any damage to the belt is visible.
Instructions
- 1
Inspect the top center portion of the plastic radiator guard for the diagram that explains the routing instructions for the single accessory belt, also known as a serpentine belt.
2Inspect the front of the motor and find the belt tensioner device that is keeping the belt tight inside of the accessory pulleys. Use the bolt that connects the pulley to the end of the tensioner arm to release the tension from the accessory belt.
3Pivot the belt tensioner device counterclockwise with a breaker bar and a socket. Pull the belt out from under the tensioner pulley. Slowly release the tension from the breaker bar until the tensioner device stops moving.
4Unwrap the belt from each accessory pulley. Slide the belt around the fan blades, and out of the engine well. Match the new and old belt together to ensure the correct size of the new belt.
5Maneuver the belt around each of the fan blades and around each accessory pulley by following the routing directions exactly as described from the belt routing diagram.
6Pivot the tensioner device counterclockwise with the breaker bar and socket. Pull the belt around the tensioner pulley, and release the tension from the breaker bar. As the tensioner pulley is springing back against the belt, the tensioner device will tighten the belt to the proper tension. Take the breaker bar off of the tensioner, and remove it from the engine well.
7Crank the engine, and let it to run for about 20 seconds or so. This will finish seating the ribs of the belt to the inside of the accessory pulley grooves. Shut the engine off.
Sunday, November 10, 2013
How to Install a Timing Belt on a 91 Honda Accord
The timing belt replacement on a 1991 Honda Accord requires removal of the balancer shaft belt. The timing belt regulates the rotation of the crankshaft and camshaft inside this models 2.2-liter engine. Timing belts should be replaced every 105,000 miles to prevent engine damage as a result of the valves colliding with the pistons if the belt breaks. This damage is both difficult and costly to repair.
Instructions
- 1
Align the two timing marks on the crankshaft sprocket with the correlating arrows on the engine block.
2Position the timing belt over the crankshaft on the side with no tension, then lead it over the camshaft sprocket, staying on the same side. Continue threading the belt in front of the water pump pulley, then pull it behind the tensioner, ending at the crankshaft sprocket again.
3Twist the tensioner nut counterclockwise to apply tension on the belt. Adjust the nut by twisting it clockwise to keep the tensioner in its position.
4Thread the balancer shaft belt over the crankshaft, then around the lower timing belt cover. Set up the crankshaft pulley and rotate the crankshaft counterclockwise six times.
5Unbolt the crankshaft pulley and lower timing belt cover, then pull the balancer shaft belt off of the crankshaft sprocket.
6Rotate the crankshaft counterclockwise until you can see three of the camshaft sprocket teeth move past the timing mark. Turn the tensioner nut counterclockwise to add tension to the timing belt.
7Torque the tensioner nut to 33 foot-lbs. with the torque wrench. Secure the tensioner locking bolt by turning it clockwise until it can go no farther.
Friday, November 8, 2013
How to Disarm a Passenger Seat Belt Alarm in a 2005 Toyota Camry
You can disarm the passenger seat belt alarm in your 2005 Toyota Camry right from your home garage, saving yourself a trip to the mechanic. The instructions can be found in your vehicles owners manual. The chime is there to remind you to fasten your safety belt, but most people just find it annoying. Just remember that if you disable it, be sure to fasten your seat belt before driving because its the law in most states.
Instructions
- 1
Put the key into the ignition and turn it one click, taking care not to start the engine.
2Push in the tiny knob several times on the instrument cluster to toggle between the trip odometer and the vehicles odometer reading. Eventually it will display "ODO" on the instrument panel. Turn off the vehicle.
3Turn on the ignition and hold the tiny knob for about 10 to 15 seconds. While still holding the knob, put on your safety belt.
4Release the knob and notice that your dashboard says "B off." The chime has been disabled.
Thursday, October 31, 2013
How to Fix the Belt on a 1996 Ford F 150
The Ford F-150 was introduced in 1975. The 1996 Ford F-150 was a 1/2 ton truck, available in both two-wheel and four-wheel drive models. The 1996 F-150 was equipped with a 4.9-liter electronic fuel injected V-6 engine in the base model. Optional engines in the 1996 F-150 included a 4.9-liter bi-fuel OHV V-6, a 5.0-liter V-8 and a 5.8-liter V-8. The drive belt on the 1996 F-150 controls the movement of several engine parts that are vital to the life of the engine, as well as the charging system and cooling system parts.
Instructions
- 1
Raise the hood on the F-150. Remove the negative battery cable from the battery, using a ratchet and socket. Remove the radiator shroud mounting bolts from the top of the radiator, then pull the radiator shroud upward and out of the engine compartment. Look beneath the hood for the belt routing diagram. If no diagram exists, draw a box on a piece of paper representing the front of the engine; draw circles on the box to represent each pulley in its position on the engine; lastly, draw a thick line between the pulleys indicating the routing of the drive belt.
2Depress the tensioner assembly with a 3/8-inch-drive ratchet, by placing the ratchet in the square hole provided in the tensioner body. The tensioner is the metal, teardrop-shaped part that has a pulley at the tip of the teardrop. Remove the drive belt from the tensioner pulley, then from the engine completely.
3Install the new drive belt over the engine cooling fan. Route the belt over each engine pulley as it appears in the routing diagram under the hood, or on the diagram that you drew. Make the belt tensioner the last stop of your belt routing. Depress the belt tensioner with the ratchet, then install the belt over the tensioner pulley.
4Check the vertical alignment of the drive belt to make sure it is centered in the grooves on each pulley. Depress the tensioner halfway and make adjustments to center the belt, if needed.
5Install the radiator shroud into the engine compartment. Tighten the shroud bolts snug with a ratchet and socket. Install the negative battery cable, and tighten it snug.
Thursday, October 24, 2013
Ford Contour Timing Belt Installation
A timing belt connects the crankshaft of a car engine to the camshaft. It synchronizes the camshaft to the crankshaft so the engine valves will open and close at the proper time. The timing belt will need to be replaced at a certain time according to the manufacturers instructions. It may also become damaged or cracked and need to be replaced before that period of time is over. If it is not replaced it can result in damage to the engine of the Ford Contour that could be very costly.
Instructions
- 1
Pop the hood of the Ford and locate the timing belt near the engine of the vehicle. Loosen and remove the accessory drive belts from the engine with an adjustable wrench.
2Take off the right motor mount on the engine. Unscrew the two bolts holding it in place with a socket wrench. Loosen the six crankshaft bolts holding the pulley in place and remove it. Take off both the upper and lower timing belt covers.
3Loosen the belt tensioner bolt and push the tensioner away from the belt. Tighten the tensioner bolt to hold it in place and remove the timing belt.
4Position the new timing belt on the pulleys and verify that all the timing marks are properly aligned. Loosen the tensioner bolt so the spring can pull it tight against the belt. Tighten down on the tensioner bolt with a wrench and make sure that there is 1/3 of an inch between the tensioner and the crankshaft pulley.
5Rotate the crankshaft two turns to realign the timing marks correctly. Put everything back in place in the reverse order that it was removed following the same procedures. Record the date or mileage that the timing belt was replaced so it will be known when it needs to be replaced again.
Wednesday, October 23, 2013
How to Replace a 2003 Hyundai Sonata Timing Belt
The 2003 Hyundai Sonata is available with a four-cylinder 2.0-liter engine with a double overhead cam. This engine design requires a timing belt to synchronize the crankshaft with the camshaft. The Sonatas timing belt should be replaced approximately every 60,000 miles.
Instructions
- 1
Remove components as required to access the cover of the timing belt on the front of the engine. Disconnect the cover with a socket wrench. Turn the crankshaft clockwise to align the timing mark on the crankshaft sprocket with the timing mark on the cylinder head. This places the No. 1 piston in the top dead center position needed to replace the timing belt.
2Disconnect the tensioner and the idler pulley for the timing belt with a socket wrench. Detach the timing belt from the crankshaft and camshaft.
3Turn the crankshaft clockwise again to align the timing marks if necessary. Connect the tensioner for the timing belt and the idler pulley. Tighten the mounting bolt for the idler pulley to between 32 and 41 ft-lbs. with a torque wrench.
4Place the timing belt over the camshaft sprocket and crankshaft sprocket in that order. Turn the timing belt tensioner to place tension on the timing belt. The timing belt is at the proper tension when five pounds of force in the middle of the longest span of the timing belt produces a deflection of 0.16 to 0.24 in.
5Tighten the bolt for the tensioner pulley to between 32 and 41 ft-lbs. with a torque wrench. Turn the crankshaft sprocket clockwise by one complete turn to realign the timing marks.
6Adjust the belt tension again if necessary. Replace the cover of the timing belt cover and any components you removed to access the timing belt.
Friday, October 18, 2013
Changing the Belt on a 2004 4Runner
Toyotas 2004 4Runner SR5 V6 and SR5 V8 models -- each with a Sport sub-model -- came equipped with a 4.0-liter V-6 engine or a 4.7-liter V-8 engine. Guess which model came with which engine. While the model names werent very imaginative, they certainly are descriptive.
Accessories Belt
The good news -- your 2004 4Runner has a single accessories belt so you dont have to fool with a bunch of belts. The bad news -- your 4Runner has a single accessories belt, which means if that belt breaks, you lose everything at once. Changing the belt is pretty much straightforward; just know that the pulley bolt for the belt tensioner has a left-handed thread. Righty-tighty, lefty-loosey doesnt apply here. The easiest way Ive found to remove the belt is to turn the belt tensioner counterclockwise and then slip the belt off the pulleys. To install the belt, route it over all the pulleys except for the top idler pulley. Turn the belt tensioner counterclockwise and then slip the belt onto the idler pulley. Especially on the 4.7-liter engine, I had to hold tension on the belt with my hand when routing it around the pulleys, since theres a lot of slack until the belt is fitted on the top idler pulley.