Showing posts with label 1996. Show all posts
Showing posts with label 1996. Show all posts

Friday, May 16, 2014

How to Troubleshoot a 1996 Chrysler Town Country

The base model of the 1996 Chrysler Town and Country minivan came equipped with a 3.3 liter six cylinder engine. The van included several different standard features including bucket seats, passenger seating for seven, an overhead console, cruise control, power steering, a tilt steering wheel, air conditioning, 15 inch wheels, power door locks and a trip computer. Because the Town and Country is comprised of so many different parts it can be difficult to know what repairs or changes to make. One way to troubleshoot the van is by working through general troubleshooting techniques.

Instructions

    1

    Look at the fuel line assembly of the Town and Country if you smell gas fumes inside the passenger compartment of the van while you are driving. There could be a loose or damaged fuel line or fuel line connector. There could also be a leaky fuel filter or the fuel tank could be punctured or damaged and leaking fuel. You should also inspect the canister purge valve of the fuel system to ensure that it isnt leaking. Make sure that the carburetor and fuel injectors inside the engine are not worn, dirty or malfunctioning.

    2

    Check the vans M.A.P. sensor when the engine has an erratic idle. Make sure the sensor is still working properly. Find the EGR valve and look to see if it has become faulty or not too. The fuel injectors could also be dirty or worn or the idle air control valve and idle speed actuator to ensure that they are not damaged, faulty or loose. The throttle position sensor could be incorrectly connected or faulty and the fuel filter could be clogged or dirty. Be sure to also inspect the PCV valve, carburetor, exhaust valves, timing gear, fuel pump, camshaft and ignition points to determine if any of these parts needs to be repaired or replaced.

    3

    Look at the differential system of the Town and Country when you hear a groaning noise coming from underneath the van while you are driving. You could have a low differential fluid level. You may also have a worn or damaged differential bearing or the wrong type of differential fluid inside the system. If you hear the groaning noise coming from the engine compartment while you are turning your steering wheel, look at the steering pump and power steering cylinder to ensure that they are not faulty. You should also check the power steering hose to make sure that it has been correctly installed and is not leaking.

Read More.. >

Sunday, May 4, 2014

How to Adjust the Clutch on a 1996 VW Jetta

Driving a VW Jetta with a manual transmission can be fun, and it gives you more control over the car. You can use the clutch to decelerate, lower the torque to the wheels, accelerate at higher rpm and even kill the engine. The whole system hinges on a clutch, which you use to change gears in the transmission and keep them from grinding each other during the speeding up and slowing down process of driving. If the clutch begins to feel less responsive or has too much slack, you may need to adjust it.

Instructions

    1

    Locate the clutch adjustment mechanism in the engine bay of the car.

    2

    Slide the locking strap down to the top of the mechanisms protective covering.

    3

    Compress the adjustment mechanism and hook the straps over the lugs protruding from the side.

    4

    Press the clutch pedal while someone else pulls the clutch cable, taking care to keep the adjustment mechanism compressed.

    5

    Unhook the locking mechanism straps and depress the clutch pedal several times until the tension is good.

Read More.. >

Thursday, October 31, 2013

How to Fix the Belt on a 1996 Ford F 150

How to Fix the Belt on a 1996 Ford F-150

The Ford F-150 was introduced in 1975. The 1996 Ford F-150 was a 1/2 ton truck, available in both two-wheel and four-wheel drive models. The 1996 F-150 was equipped with a 4.9-liter electronic fuel injected V-6 engine in the base model. Optional engines in the 1996 F-150 included a 4.9-liter bi-fuel OHV V-6, a 5.0-liter V-8 and a 5.8-liter V-8. The drive belt on the 1996 F-150 controls the movement of several engine parts that are vital to the life of the engine, as well as the charging system and cooling system parts.

Instructions

    1

    Raise the hood on the F-150. Remove the negative battery cable from the battery, using a ratchet and socket. Remove the radiator shroud mounting bolts from the top of the radiator, then pull the radiator shroud upward and out of the engine compartment. Look beneath the hood for the belt routing diagram. If no diagram exists, draw a box on a piece of paper representing the front of the engine; draw circles on the box to represent each pulley in its position on the engine; lastly, draw a thick line between the pulleys indicating the routing of the drive belt.

    2

    Depress the tensioner assembly with a 3/8-inch-drive ratchet, by placing the ratchet in the square hole provided in the tensioner body. The tensioner is the metal, teardrop-shaped part that has a pulley at the tip of the teardrop. Remove the drive belt from the tensioner pulley, then from the engine completely.

    3

    Install the new drive belt over the engine cooling fan. Route the belt over each engine pulley as it appears in the routing diagram under the hood, or on the diagram that you drew. Make the belt tensioner the last stop of your belt routing. Depress the belt tensioner with the ratchet, then install the belt over the tensioner pulley.

    4

    Check the vertical alignment of the drive belt to make sure it is centered in the grooves on each pulley. Depress the tensioner halfway and make adjustments to center the belt, if needed.

    5

    Install the radiator shroud into the engine compartment. Tighten the shroud bolts snug with a ratchet and socket. Install the negative battery cable, and tighten it snug.

Read More.. >

Sunday, September 15, 2013

How to Install a Choke Cable on a 1996 883 Sportster

How to Install a Choke Cable on a 1996 883 Sportster

Chokes help cold engines start. Pulling the choke knob out increases the percentage of gasoline in the fuel air mix. Pushing the knob in decreases the amount of gasoline. The knob simply pushes and pulls a thin wire with a tiny ball on the end into and out of a slot in the back of the carburetor. When chokes are properly lubricated they last for at least a decade. Eventually they wear out or break and when they are broken their owners are often stumped because replacing a choke is a rarely performed job.

Instructions

    1

    Close the petcock valve. Run the engine until it dies. Unhook the old choke cable from the clip near the horn.

    2

    Loosen the two Allen screws on the air cleaner cover with an Allen wrench. Unplug the breather tubes from the air cleaner.

    3

    Loosen the air cleaner Allen screws with an Allen wrench and remove the air cleaner. Loosen the backing plate Allen screws and remove the air cleaner backing plate.

    4

    Loosen the fuel line hose clamp with a flathead screwdriver and unplug the fuel line from the carburetor.

    5

    Label the front and back throttle cables. Remove the cables from the throttle cam.

    6

    Gently pull the carburetor out of the intake manifold boot with both hands. Remove the carburetor and choke cable as a single unit.

    7

    Unscrew the black, plastic, cable sealing cap on the back of the carburetor that connects the choke assembly to the carburetor body. Remove the spring inside the sealing cab and remove the choke valve by gently lifting the cable up and out.

    8

    Thread the wire end of the new choke assembly into the hole in the back of the carburetor. Push the ball and wire down into the slot.

    9

    Replace the spring and tighten the sealing cap hand tight.

    10

    Thread the new choke knob under the gas tank to the choke knob clip. Replace the carburetor in the intake manifold boot. Snap the choke knob into the clip.

    11

    Replace and readjust both throttle cables by hand. Reattach the fuel line to the carburetor using a new hose clamp and a flathead screwdriver.

    12

    Reattach the air cleaner backing plate using the Allen screws and an Allen wrench. Reattach the breather tubes by hand.

    13

    Reinstall the air cleaner and the air cleaner cover using an Allen wrench.

Read More.. >