Friday, June 6, 2014
How to Troubleshoot a Motorcycle Carburetor
A carburetor is a device responsible for regulating the amount of fuel and air inside the cylinders of a motorcycle engine in order to maximize performance. The carburetor is a very expensive device to replace and it can become damaged from fuel clogs and mechanical failure. It requires regular maintenance to maintain proper function. If a carburetor starts to have problems, troubleshooting it becomes a necessity to keep the motorcycle in prime running condition.
Instructions
- 1
Start the motorcycle. If your motorcycle was running fine the last time it was used but then sat for an extended period of time (during the winter for example), the fuel may have broken down and gummed up the carburetor. The most common symptom of this is that the bike will not start properly after sitting for an extended period of time. If this is the case, you will need to remove and clean the carburetor.
2Run the motorcycle at a low RPM if you are able to. If the bike has trouble running at low RPM when the idle is at 1/4 throttle, the pilot system or the slide valve is the likely culprit.
3Increase the RPM gradually if the bike is still running. The engine is directly affected by the throttle of the carburetor. If the engine starts having problems between 1/4 and 3/4 throttle, the jet needle is more likely the problem and may need replacement. If the problem is happening at more than 3/4 throttle, the main fuel jet in the carburetor is the most likely issue.
Tuesday, February 11, 2014
428 Motorcycle Chain Specs
Motorcycles use chains to move power from the transmission to the wheels. Roller chains have two types of links. The inner link had two plates held together by two pins with sleeves covering the pins. Two rollers ride the bushings and touch the sprocket of the rear wheel. The outer link is simply a connector plate holding two inner links together. The 428 chain keeps power flowing on modern motorcycles and motorcycle-based small vehicles, such as ATVs.
Dimensions of the Links
The inside width is the distance between the inside plates. Inside width of the 428 measures 7.95 mm. Pitch is the distance between the centers of the two inner link pins and is 12.700 mm on the 428. The roller diameter for the 428 is 8.51 mm. The pins inside the sleeves inside the rollers of the 428 are 4.45 mm thick and 16.7 mm long. The plates holding the inner links together are 1.60 mm thick.
The Strength of the Chain
The American National Standards Institute tested the 428 chain for tensile strength and found that it takes a weight of 3,125 pounds to break it. ANSI recommends that the load on the 428 chain never exceed 810 pounds in continuous use.
The Weight of the Chain
The 428 chain weighs 71 kg per meter of chain.
Saturday, November 30, 2013
How to Time a Harley Davidson Motorcycle
Checking the timing on your Harley-Davidson motorcycle every 5,000 miles plays an important role in a comprehensive maintenance routine. As a Harley-Davidson engine ages, you must adjust the ignition timing to compensate for the wear of internal engine parts. Setting the timing correctly keeps your motorcycle running smoothly and efficiently. Maladjusted timing may result in sluggish performance, poor fuel economy and possible damage to internal engine components. Setting the timing is relatively easy and ensures the maximum life from the engine.
Instructions
- 1
Remove the crankcase timing plug using an Allen wrench, and expose the timing hole. The timing hole is located on the primary chain case side of the motor on the engine block and capped with a solid hex-head plug. Install a clear plastic timing hole plug to prevent oil splash.
2Connect the positive terminal of an inductive timing light to the positive battery terminal of the motorcycle. Connect the negative terminal of the timing light to the negative terminal of the battery. Connect the inductive pickup probe of the timing light to the front cylinder spark plug wire.
3Start the engine, and run it at idle. Point the timing light into the timing inspection hole. If the ignition is properly timed, the timing bar will align with the circular timing reference mark. The reference marks on a correctly timed engine will appear as a vertical bar through the center of the circle. Some models only have a timing reference mark on the flywheel of the motor; on these models, the engine is correctly timed when the reference mark is visible in the timing inspection hole.
4Remove the timing cover from the right side of the motor with a Phillips screwdriver or Allen wrench, depending on your specific model. Loosen the the timing plate screws with a slotted screwdriver, and turn the timing plate to adjust the timing. Recheck the timing marks with the timing light. Tighten the timing plate screws, and install the cover.
5Shut off the engine, and remove the timing light. Remove the clear plastic timing hole plug, and install the solid plug in the hole.
Friday, November 15, 2013
How to Use a Motorcycle Belt Adjustment Tool
Motorcycle belt adjustment tools are designed to adjust the tension and alignment on your motorcycle belts. Performing this adjustment yourself can help you better understand the mechanics of your motorcycle and help you troubleshoot any problems that arise with the belts on your motorcycle. Adjustment is easier if you are accustomed to using a belt adjustment tool.
Instructions
- 1
Stand your motorcycle in an upright position with a kickstand and four concrete blocks. Secure its position with the blocks on both sides of the front tire so that the motorcycle does not rock back and forth while you are working on it.
2Place the transmission into neutral and elevate the rear tire by placing a concrete block or jack under the rear suspension. You will need the rear tire to be able to spin freely to check the belt tension.
3Rotate the rear tire and measure the tight spots of the belt. Note the deflection of the belt as you rotate the rear tire in four places. Measure the deflection with a tape measure or a ruler approximately half the distance between the front and rear sprockets on the lower part of the belt. Note the tightest point on the belt and mark this area with your silver permanent marker.
4Adjust the wheel alignment if the left and right notches are not at the same marks or position of the swing arm. Be sure to do this before adjusting your belt.
5Use the tension gauge to push up the belt in the center from underneath, using 10 pounds of pressure (indicated on the tool), with maximum deflection of 1.5 mm to 4 mm at the front of the swing arm cross pipe. Repeat at the areas that you marked with the silver marker. Adjust your belt as needed for your motorcycles specifications
Saturday, October 26, 2013
Honda Motorcycle Tools
A small, portable tool kit is an essential part of being a motorcycle owner. You can fix simple issues on your Honda motorcycle, such as switching out a bad spark plug or tightening a loose bolt--if you have the right tools. Check with the owners manual of your model Honda motorcycle for the exact specs of the tools needed to work on it.
Spark Plug Socket
If you own a motorcycle, chances are good that you will need to change out your spark plugs often. If this happens when you are out in the middle of a ride, you will need to change them on the road. Always carry extra spark plugs and a spark plug socket, a small wrench made especially for removing spark plugs. Make sure your spark plug socket is for a metric motor. Check your Honda motorcycle owners manual to see what type of spark plugs your engine requires.
Multi-Tool
As its name implies, a multi-tool is a compact tool that can perform a variety of functions. It can be a knife, a screwdriver or pliers to name a few. Several companies make multi-tools, but theyre universal, so choose the one that performs the most useful functions for you (see Resources).
Allen Wrench Set
An Allen wrench is also known as a "hex key." An Allen wrench set includes several sizes for various jobs. The hexagonal heads are used to drive the bolts and screws on your Honda motorcycle that have hexagonal sockets. Allen wrenches are light and small so they can be carried along with you on your motorcycle.
Friday, October 4, 2013
How to Locate Shocks for a Yamaha Motorcycle
When the ride on your Yamaha motorcycle is less than smooth, you may need to replace the shocks. The shocks on your bike absorb the impact as the bike moves over uneven roads. Several retail options are available where you can purchase the right shocks. Its best to shop for the best price.
Instructions
- 1
Purchase parts directly from the source, especially if you have a Yamaha warranty on your shocks. You can find a local Yamaha dealer on the Yamaha Dealer Locator. Tell them which shocks you need. If you arent sure, theyll be able to help you.
2Go to a local motorcycle retailer, even if they dont specifically stock Yamahas. They should have access to the type of shocks you need and can help you find the correct part if you give them the model and year of your Yamaha.
3Purchase parts online. There are hundreds of retailers who sell Yamaha parts over the Internet, including jcwhitney.com, bikebandit.com and motorcycle-superstore.com. If you have the product information for your shocks, you can find them on an online site and have them sent to you. You will have to pay shipping if you order your shocks online.