Friday, June 6, 2014
How to Troubleshoot a Motorcycle Carburetor
A carburetor is a device responsible for regulating the amount of fuel and air inside the cylinders of a motorcycle engine in order to maximize performance. The carburetor is a very expensive device to replace and it can become damaged from fuel clogs and mechanical failure. It requires regular maintenance to maintain proper function. If a carburetor starts to have problems, troubleshooting it becomes a necessity to keep the motorcycle in prime running condition.
Instructions
- 1
Start the motorcycle. If your motorcycle was running fine the last time it was used but then sat for an extended period of time (during the winter for example), the fuel may have broken down and gummed up the carburetor. The most common symptom of this is that the bike will not start properly after sitting for an extended period of time. If this is the case, you will need to remove and clean the carburetor.
2Run the motorcycle at a low RPM if you are able to. If the bike has trouble running at low RPM when the idle is at 1/4 throttle, the pilot system or the slide valve is the likely culprit.
3Increase the RPM gradually if the bike is still running. The engine is directly affected by the throttle of the carburetor. If the engine starts having problems between 1/4 and 3/4 throttle, the jet needle is more likely the problem and may need replacement. If the problem is happening at more than 3/4 throttle, the main fuel jet in the carburetor is the most likely issue.
Monday, March 24, 2014
How to Rebuild the EMPI in a Carburetor
The carburetor on a vehicle is used for the internal combustion inside the engine. This works by mixing the fuel with air to create the combustion that propels the engine while driving. A European Motor Parts Incorporated carburetor kit allows you to replace any worn or leaking parts in your carb. These kits can be used with everything from a VW Beetle to a 78 Chevy. If you would like to rebuild your carburetor with an EMPI kit, you can do it with little hassle. You dont have to be an auto mechanic to rebuild your carburetor; you can do it yourself even if you have minimal knowledge of the task.
Instructions
- 1
Buy an EMPI carburetor kit. This can be found at local auto parts stores or through an online outlet. EMPI kits come with all of the rubber seals and gaskets that you need to rebuild your carb.
2Put on safety glasses and gloves to keep grease and dirt off of your hands and out of your eyes. Remove the carburetor from your vehicle. Consult your service manual if you do not know how to remove the unit, as the process can vary from car to car.
3Look over the diagram that came with your EMPI kit. This diagram will vary depending on the carburetor kit specific to your vehicle. Use a ratchet to remove the accelerator pump from your carburetor. Remove the cover from your carb and then remove the choke linkages as well. All of these parts are labeled on the diagram that comes with your EMPI kit.
4Use a stiff-bristled toothbrush and cleaner to remove all debris from the parts on your carburetor. Use the EMPI kit diagram to replace the broken parts on your carb. Put the carburetor back together and then reinstall the carburetor in your car.
Thursday, January 30, 2014
How to Set the Float Level on a Weber Carburetor
Setting the float height on a Weber carburetor is important to the proper operation of the engine. Any time a new or rebuilt carburetor is used, the float height must be checked. A float level that is too high will cause the engine to run rich and may flood the carburetor with too much gas. A float that is too low will make the engine run lean and cause poor performance. Adjusting the float height is an easy task that does not require special tools or expertise.
Instructions
- 1
Remove the fuel line, choke thermostat wire and carburetor flange mounting bolts. Remove the throttle linkage and lift the carburetor off the vehicle. Place a clean shop rag over the exposed intake manifold to prevent dirt and debris from entering the engine.
2Remove the six retaining screws on the top of the carburetor. Remove the clip holding on the choke linkage. Be caul not to damage the clip. Remove the top of the carburetor. The carburetor may have gasoline inside the float bowl; drain any residual gas into a fuel proof container and dispose of properly.
3Hold the carburetor at approximately a 45-degree angle and allow the float to hang freely. Measure the bottom of the float to ensure both sides are parallel to the gasket surface of the carburetor body. Bend the float to correct any warpage between the two sides of the float.
4Hold the carburetor upside down so that the float is resting on the float valve. Measure from the bottom surface of the float to the machined gasket surface of the carburetor body. Bend the float tab until the reading is 1.5 inches or 38.5 mm.
5Install the top of the carburetor and tighten the six hold down screws. Attach the choke rod with the retaining clip. Remove the shop rag on the intake manifold and install the carburetor on the vehicle. Connect the fuel line, throttle linkage, choke wire and hold down bolts. Start the vehicle and check for leaks.