Thursday, January 30, 2014
How to Set the Float Level on a Weber Carburetor
Setting the float height on a Weber carburetor is important to the proper operation of the engine. Any time a new or rebuilt carburetor is used, the float height must be checked. A float level that is too high will cause the engine to run rich and may flood the carburetor with too much gas. A float that is too low will make the engine run lean and cause poor performance. Adjusting the float height is an easy task that does not require special tools or expertise.
Instructions
- 1
Remove the fuel line, choke thermostat wire and carburetor flange mounting bolts. Remove the throttle linkage and lift the carburetor off the vehicle. Place a clean shop rag over the exposed intake manifold to prevent dirt and debris from entering the engine.
2Remove the six retaining screws on the top of the carburetor. Remove the clip holding on the choke linkage. Be caul not to damage the clip. Remove the top of the carburetor. The carburetor may have gasoline inside the float bowl; drain any residual gas into a fuel proof container and dispose of properly.
3Hold the carburetor at approximately a 45-degree angle and allow the float to hang freely. Measure the bottom of the float to ensure both sides are parallel to the gasket surface of the carburetor body. Bend the float to correct any warpage between the two sides of the float.
4Hold the carburetor upside down so that the float is resting on the float valve. Measure from the bottom surface of the float to the machined gasket surface of the carburetor body. Bend the float tab until the reading is 1.5 inches or 38.5 mm.
5Install the top of the carburetor and tighten the six hold down screws. Attach the choke rod with the retaining clip. Remove the shop rag on the intake manifold and install the carburetor on the vehicle. Connect the fuel line, throttle linkage, choke wire and hold down bolts. Start the vehicle and check for leaks.
Saturday, November 16, 2013
How to Set Up a Parts Washer
A parts washer is a key piece of equipment in any repair facility or manufacturing plant. Parts washers utilize water and detergents at high temperatures and pressure to remove grease, oil, bits of metal and other such debris. Detergents designed specifically for parts washers aid in the removal of debris. Liquid soaps work best for degreasing while powders clean most aggressively. Jet sprays or power washing cycles ramp up the cleaning power of the machines.
Instructions
Set Up
- 1
Unpack the parts washer. Use care when lifting such a heavy object. Discard packing materials but keep warranty information or other accompanying paperwork.
2Lift the parts washer lid. Remove the pieces of the parts washer packed inside such as the timer, oil skimmer, basket and debris screen. Place these items aside.
3Move the parts washer into its permanent place. Select a position near a 115V (220AC) electrical outlet outfitted with GFCI, or Ground Fault Circuit Interrupter, for maximum safety. Do not plug in the parts washer yet!
4Locate the bottom frame bar inside the washer. Fill the parts washer with water to that point.
5Return the debris screen and the basket to the parts washer. Close the lid. Plug in the washer.
6Find the timer on the oil skimmer. Select a time for the daily oil skimming. Fit the oil skimmer onto the parts washer.
7Move a 5 gallon bucket under the drain spout to catch skimmed oil. Plug in the oil skimmer.
8Locate the thermostat. Adjust the temperature to the manufacturers recommended setting.
9Find the wash cycle knob. Select a quick 10-minute cycle.
10Test the machines safety apparatus by lifting the lid during the cycle. Adjust the sensitivity switch located along the top of the washer if the machine fails to stop when the lid is lifted. Test again.
11Give the machine 10 to 12 hours to reach the optimum temperature. Add liquid or powder soap according to the manufacturer guidelines.
Tuesday, November 5, 2013
How to Set a Carbs Float Level
In carbureted engines, a float bowl in the carburetor holds fuel prior to it being fed into the engine. Fuel is pumped from the fuel tank into the bowl of the carburetor; the amount of fuel held is closely controlled by the "float". The float is a simple buoyancy device that rises or falls as the fuel increases or decreases. It controls the amount of fuel allowed into the carburetor by opening or closing a valve, depending on its float height. Adjusting floats must be done very accurately to prevent overflow of fuel or stalling.
Instructions
- 1
Determine whether your float level is too high or too low. If too high, you will most likely have fuel run off through an overflow tube. If a glass sight window is present, the fuel level will be toward the upper side of the window. If your float level is too low, the vehicle will run out of fuel when driving at high speeds, or the window will show a fuel level toward the bottom of it. The fuel level should always be in the middle of the window and should not ever overflow.
2Remove the carburetor or the float bowl. On motorcycles, the float bowl can often be removed while leaving the carburetor on the bike. On cars it depends on the model and location of the carburetor. Be careful not to drop or lose any small parts; the bowl and carburetor must be replaced exactly as removed.
3Locate the hinge of the float and find the float needle, which will be a small metal or plastic rod that is pushed up by the bracket that holds the float. When the float is pushed up by the fuel, the float needle is pushed up, which closes off the fuel supply from the fuel tank. When the float goes down due to a lack of fuel, the needle drops, allowing more fuel in.
4Push the tab that holds and pushes the float needle up 1/32 inch with a flat head screwdriver, if you have determined your carburetor float is too low. Pull it down the same distance, if you have determined your float is too high. Be very careful not to bend any other elements on the float assembly when doing this.
5Replace the bowl or the carburetor, and replace the fuel line. Check the height of fuel through the window, or take a test drive and check the results. Readjust as necessary.