Showing posts with label level. Show all posts
Showing posts with label level. Show all posts

Thursday, January 30, 2014

How to Set the Float Level on a Weber Carburetor

How to Set the Float Level on a Weber Carburetor

Setting the float height on a Weber carburetor is important to the proper operation of the engine. Any time a new or rebuilt carburetor is used, the float height must be checked. A float level that is too high will cause the engine to run rich and may flood the carburetor with too much gas. A float that is too low will make the engine run lean and cause poor performance. Adjusting the float height is an easy task that does not require special tools or expertise.

Instructions

    1

    Remove the fuel line, choke thermostat wire and carburetor flange mounting bolts. Remove the throttle linkage and lift the carburetor off the vehicle. Place a clean shop rag over the exposed intake manifold to prevent dirt and debris from entering the engine.

    2

    Remove the six retaining screws on the top of the carburetor. Remove the clip holding on the choke linkage. Be caul not to damage the clip. Remove the top of the carburetor. The carburetor may have gasoline inside the float bowl; drain any residual gas into a fuel proof container and dispose of properly.

    3

    Hold the carburetor at approximately a 45-degree angle and allow the float to hang freely. Measure the bottom of the float to ensure both sides are parallel to the gasket surface of the carburetor body. Bend the float to correct any warpage between the two sides of the float.

    4

    Hold the carburetor upside down so that the float is resting on the float valve. Measure from the bottom surface of the float to the machined gasket surface of the carburetor body. Bend the float tab until the reading is 1.5 inches or 38.5 mm.

    5

    Install the top of the carburetor and tighten the six hold down screws. Attach the choke rod with the retaining clip. Remove the shop rag on the intake manifold and install the carburetor on the vehicle. Connect the fuel line, throttle linkage, choke wire and hold down bolts. Start the vehicle and check for leaks.

Read More.. >

Tuesday, November 5, 2013

How to Set a Carbs Float Level

How to Set a Carbs Float Level

In carbureted engines, a float bowl in the carburetor holds fuel prior to it being fed into the engine. Fuel is pumped from the fuel tank into the bowl of the carburetor; the amount of fuel held is closely controlled by the "float". The float is a simple buoyancy device that rises or falls as the fuel increases or decreases. It controls the amount of fuel allowed into the carburetor by opening or closing a valve, depending on its float height. Adjusting floats must be done very accurately to prevent overflow of fuel or stalling.

Instructions

    1

    Determine whether your float level is too high or too low. If too high, you will most likely have fuel run off through an overflow tube. If a glass sight window is present, the fuel level will be toward the upper side of the window. If your float level is too low, the vehicle will run out of fuel when driving at high speeds, or the window will show a fuel level toward the bottom of it. The fuel level should always be in the middle of the window and should not ever overflow.

    2

    Remove the carburetor or the float bowl. On motorcycles, the float bowl can often be removed while leaving the carburetor on the bike. On cars it depends on the model and location of the carburetor. Be careful not to drop or lose any small parts; the bowl and carburetor must be replaced exactly as removed.

    3

    Locate the hinge of the float and find the float needle, which will be a small metal or plastic rod that is pushed up by the bracket that holds the float. When the float is pushed up by the fuel, the float needle is pushed up, which closes off the fuel supply from the fuel tank. When the float goes down due to a lack of fuel, the needle drops, allowing more fuel in.

    4

    Push the tab that holds and pushes the float needle up 1/32 inch with a flat head screwdriver, if you have determined your carburetor float is too low. Pull it down the same distance, if you have determined your float is too high. Be very careful not to bend any other elements on the float assembly when doing this.

    5

    Replace the bowl or the carburetor, and replace the fuel line. Check the height of fuel through the window, or take a test drive and check the results. Readjust as necessary.

Read More.. >