Showing posts with label seat. Show all posts
Showing posts with label seat. Show all posts

Friday, June 6, 2014

How to Turn Off the Seat Belt Warning on a Toyota Camry

How to Turn Off the Seat Belt Warning on a Toyota Camry

Newer Toyota Camrys are equipped with a bell that warns you to put on your seat belt before starting the car. Some people find it annoying and wish to turn off the chiming. There are instructions in the owners manual on how to do this. You dont need any special tools to turn off this seat belt warning and it will only take a few moments of your time.

Instructions

    1

    Put the key into the ignition and turn it to the on position, but do not start the engine.

    2

    Look for a tiny knob on the instrument panel and press it to toggle between the odometer reading and the trip odometer reading. Keep pressing the knob until you see "ODO." Turn off the vehicle.

    3

    Turn the ignition on but dont crank the engine. Pull the tiny knob out for 10 seconds. While still holding the knob out, put on your seat belt and keep holding the knob for another 5 seconds then release it. The instrument panel will now read "B off."

    4

    Repeat the above procedure to turn the seat belt warning chime back on.

Read More.. >

Monday, February 3, 2014

How to Remove the Back Seat on a 2005 Acura RL

How to Remove the Back Seat on a 2005 Acura RL

The Acura RL was introduced to replace the Acura Legend. Both cars are luxury models produced by Japanese automaker Honda. The RL designation stands for "Road Luxury." If you decide that you want to remove the back seat on your 2005 Acura RL, you can do so in your home garage and save yourself some time and money. Maybe youd like to have the carpet cleaned or you are reupholstering or replacing the seat. In any case, it will take you about 30 minutes to complete this task, and you will need only one tool that can be purchased from any auto parts or hardware store.

Instructions

    1

    Move the front seats as far forward as possible. Open all the doors.

    2

    Separate the crevice between the seat back and the seat cushion with your hands to locate the bolt that holds the seat cushions in place. Remove this bolt with a socket wrench.

    3

    Pull the latches under the seat cushion forward and remove the seat cushion.

    4

    Locate the three bolts under each seat back and remove with a socket wrench. Remove the two bolts under each headrest with a socket wrench.

    5

    Pull the seat back forward and lift it out of the side door of your Acura.

Read More.. >

Friday, November 8, 2013

How to Disarm a Passenger Seat Belt Alarm in a 2005 Toyota Camry

How to Disarm a Passenger Seat Belt Alarm in a 2005 Toyota Camry

You can disarm the passenger seat belt alarm in your 2005 Toyota Camry right from your home garage, saving yourself a trip to the mechanic. The instructions can be found in your vehicles owners manual. The chime is there to remind you to fasten your safety belt, but most people just find it annoying. Just remember that if you disable it, be sure to fasten your seat belt before driving because its the law in most states.

Instructions

    1

    Put the key into the ignition and turn it one click, taking care not to start the engine.

    2

    Push in the tiny knob several times on the instrument cluster to toggle between the trip odometer and the vehicles odometer reading. Eventually it will display "ODO" on the instrument panel. Turn off the vehicle.

    3

    Turn on the ignition and hold the tiny knob for about 10 to 15 seconds. While still holding the knob, put on your safety belt.

    4

    Release the knob and notice that your dashboard says "B off." The chime has been disabled.

Read More.. >

Sunday, October 27, 2013

Explorer Third Row Power Seat Problems

Explorer Third Row Power Seat Problems

The Explorer, a mid-size sports utility vehicle manufactured by the Ford Motor Company, has experienced a variety of issues related to its third-row seating. These problems vary from minor inconveniences to major issues that may pose safety concerns and necessitate the replacement of the entire seat.

Seat Wont Elevate

    Most Ford Explorers are equipped with power seating. Power seating allows the user to adjust the seat to meet their individual preferences through the push of a button, permitting the user to raise, lower or move their seat forward or backward. When the seat will not elevate, a common culprit is a bad motor gear. Over time, the motor that is responsible for allowing the seat raise or move forward or backward may become worn, causing failure of the motor to operate properly. When this occurs, it is oftentimes necessary for the motor to be replaced in order for the seat to operate properly.

Heated Seats

    The Ford Explorer also offered heated seats on both driver and passenger seats. While heated seats can be an added luxury, heated seats that fail to work properly can sometimes present a safety hazard. In order to operate the heat feature on the Ford Explorer, the user must push the heat activation button located on the instrument panel on the side of the seat. To turn the heat option off, the button should be pressed again. If the heat fails to shut off, this may indicate a wiring issue that is preventing the heat option from deactivating. Heated seats that fail to shut off on command can lead to serious burns and may need to be replaced in order to prevent harm.

Seats Wont Fold

    Another common problem with Ford Explorer third row seating is seats that will not fold down into the floor in order to create a cargo area. When this occurs, a common culprit is head rests that are not folded down enough to allow the seat to collapse. Pulling the black tab forward under both headrests should allow the headrest to fold down completely. From there, try to fold the seats down as usual. If the seats fail to fold after ensuring that your headrests are fully folded, this may indicate a problem with the release, which will need to be inspected by a certified mechanic to determine whether or not the seat is repairable or will need to be replaced.

Read More.. >

Wednesday, October 9, 2013

How to Wire a Power Seat in a 2000 Infiniti I30

The Infiniti I30 was Nissans first serious entry into the luxury-car market. Hoping to emulate Toyotas success with the Lexus brand, Nissan up-contented their basic cars into luxury offerings. The I30 was essentially a re-badged Nissan Maxima with an upgraded interior and a more supple ride. Power seats were standard and allowed driver and passenger to change the position of their seats with the press of a button. However the motors in these seats can burn out and a replacement seats need to be wired into place.

Instructions

    1

    Drive the Infiniti I30 somewhere flat and with ample room to the drivers side. Car seats are bulkier than they look and having the flat ground helps keep the seat from sliding around on the rails. Put the Infiniti into "Park" and pull the emergency brake up before turning the car off. Pull the hood latch and go around to the front of the car. Open the trunk hood up and disconnect the black wire from the car battery.

    2

    Turn the power button to off on the underside of the power seat. Push the seat forward and unbolt the two rear retaining bolts on each rail. Move the seat to the rear and unbolt each bolt on the front of the rails. Pull them up and off, but not out of the car. Disconnect the power wire from the bottom of the seat, then take the seat out. Pull the runner assembly off the rails and disconnect the power wire from the gear box.

    3

    Pull the carpet flap off the bottom of the power seat and disconnect the wiring harness from each motor. Pull the carpet flap off of the new power seat and plug the wiring harness into the bottom of the seat. Slide the carpet flap back over so that only the single power port is left out at the rear.

    4

    Slide the runners at the bottom of the seat onto the rails. Bolt in the retaining bolts at the rear and then at the front of the seat. Plug the power cord coming from the floor into the port coming from the wiring harness. Reconnect the black wire to the car battery, shut the hood and turn the car back on. Test the Infinitis power seat by moving it forward, back, and angle it forward and to the rear.

Read More.. >