Monday, November 17, 2014
How to Wire a Blower Motor Resistor
Most vehicles today have multiple fan speeds for the heat and A/C. These speeds are controlled by a blower motor resistor. The blower motor resistor is a small electrical device that controls the voltage to the fan motor. If the resistor becomes defective, you may only have one working speed on your fan control. If this problem occurs, the blower motor resistor will need to be replaced. It s a fairly inexpensive part and is available at most car part stores.
Instructions
- 1
Locate the heater blower resistor in your vehicle. It is typically mounted under the dash near the blower motor. You may need to check your vehicles repair guide, or your car dealership to help determine the resistors location. Parts of the dash may need to be removed depending on resistor location.
2Remove the wire connector from the blower motor resistor by lifting the tab on the connector and gently pulling the connector off the resistor. This may require working the connector back and forth a few times to free it from the resistor.
3Remove the two screws holding the resistor in place. These may be screws or small bolts depending on your vehicle. The resistor should now be able to be removed.
4Position the new resistor in place, and secure it with the two screws. Reconnect the wire connector by firmly pressing it onto the resistor. Replace and dash parts that were previously removed.
Friday, December 20, 2013
How to Install the Auto Volt Gauge Wire
A volt gauge for an automobile measures the voltage in your vehicless electrical system. It typically functions only while the ignition is on, and an auto volt gauge may include a warning light for when the voltage is outside the normal operating range. You must mount an auto volt gauge where you can see it while driving, usually under the dashboard. The kit for an auto volt gauge contains mounting hardware specific to that volt gauge.
Instructions
- 1
Find a fuse in your vehicles fuse box that does not receive any current unless your vehicles ignition is on. Common choices include the fuse for your stereo system or your power windows. Pull this fuse from its socket.
2Attach the mount for the volt gauge in a convenient location, according to the instructions. This will typically require you to drill holes in the dashboard with a drill, and fasten the volt gauge mount with screws.
3Cut two lengths of 14-gauge electrical wire that are several feet long. Strip inch of the insulation from one end of each wire. Connect the bare end of one of these wires to the positive terminal of the voltage gauge with electrical tape. Connect the bare end of the other wire to the negative terminal of the voltage gauge with electrical wire. Attach the volt gauge to its mount according to the instructions.
4Route the free end of the negative wire to a grounded screw on the dashboard. Cut off the excess wire and strip the insulation from the last half inch of the wire. Loosen the grounded screw, wrap the wire around it and tighten the screw.
5Route the free end of the positive wire to the fuse box. Cut off the excess wire and strip inch of the insulation from the end of the wire. Push the bare end of the positive wire into the empty fuse socket and replace the fuse. Secure the end of the positive wire with electrical tape.
Wednesday, October 9, 2013
How to Wire a Power Seat in a 2000 Infiniti I30
The Infiniti I30 was Nissans first serious entry into the luxury-car market. Hoping to emulate Toyotas success with the Lexus brand, Nissan up-contented their basic cars into luxury offerings. The I30 was essentially a re-badged Nissan Maxima with an upgraded interior and a more supple ride. Power seats were standard and allowed driver and passenger to change the position of their seats with the press of a button. However the motors in these seats can burn out and a replacement seats need to be wired into place.
Instructions
- 1
Drive the Infiniti I30 somewhere flat and with ample room to the drivers side. Car seats are bulkier than they look and having the flat ground helps keep the seat from sliding around on the rails. Put the Infiniti into "Park" and pull the emergency brake up before turning the car off. Pull the hood latch and go around to the front of the car. Open the trunk hood up and disconnect the black wire from the car battery.
2Turn the power button to off on the underside of the power seat. Push the seat forward and unbolt the two rear retaining bolts on each rail. Move the seat to the rear and unbolt each bolt on the front of the rails. Pull them up and off, but not out of the car. Disconnect the power wire from the bottom of the seat, then take the seat out. Pull the runner assembly off the rails and disconnect the power wire from the gear box.
3Pull the carpet flap off the bottom of the power seat and disconnect the wiring harness from each motor. Pull the carpet flap off of the new power seat and plug the wiring harness into the bottom of the seat. Slide the carpet flap back over so that only the single power port is left out at the rear.
4Slide the runners at the bottom of the seat onto the rails. Bolt in the retaining bolts at the rear and then at the front of the seat. Plug the power cord coming from the floor into the port coming from the wiring harness. Reconnect the black wire to the car battery, shut the hood and turn the car back on. Test the Infinitis power seat by moving it forward, back, and angle it forward and to the rear.
Tuesday, September 17, 2013
How to Wire the BCM in a 2002 Impala
The 2002 Impala was a mid-size four-door sedan manufactured by the Chevrolet division of General Motors. It is an eighth-generation Impala, which includes the 2000 to 2005 models. These models had anti-lock brakes as a standard feature, which provide better braking when the vehicle begins to lose traction. The brake control module, or BCM, is a microprocessor that reduces the braking force to a wheel that is spinning more slowly than the other wheels.
Instructions
- 1
Remove the cable from the negative battery terminal with a socket wrench. This ensures that an electrical discharge does not damage the BCM when you replace it.
2Locate the BCM. It is the black box to the left of the steering column and under the instrument panel.
3Push the pressure tabs on the BCM together to release the BCM, and detach the BCM from its bracket. Unplug the wiring harness from the BCM, and remove the BCM from the vehicle.
4Push the connector for the wiring harness into its slot on the new BCM. The connector makes an audible click when it is securely connected to the BCM.
5Install the BCM to its bracket on the vehicle. The pressure tabs on the BCM make an audible click when the BCM is securely fastened to its bracket.
6Attach the cable to the negative terminal of the battery with a socket wrench.