Monday, November 17, 2014
How to Wire a Blower Motor Resistor
Most vehicles today have multiple fan speeds for the heat and A/C. These speeds are controlled by a blower motor resistor. The blower motor resistor is a small electrical device that controls the voltage to the fan motor. If the resistor becomes defective, you may only have one working speed on your fan control. If this problem occurs, the blower motor resistor will need to be replaced. It s a fairly inexpensive part and is available at most car part stores.
Instructions
- 1
Locate the heater blower resistor in your vehicle. It is typically mounted under the dash near the blower motor. You may need to check your vehicles repair guide, or your car dealership to help determine the resistors location. Parts of the dash may need to be removed depending on resistor location.
2Remove the wire connector from the blower motor resistor by lifting the tab on the connector and gently pulling the connector off the resistor. This may require working the connector back and forth a few times to free it from the resistor.
3Remove the two screws holding the resistor in place. These may be screws or small bolts depending on your vehicle. The resistor should now be able to be removed.
4Position the new resistor in place, and secure it with the two screws. Reconnect the wire connector by firmly pressing it onto the resistor. Replace and dash parts that were previously removed.
Sunday, April 13, 2014
How to Know if an A C Blower Is Bad
There are many reasons that a cars air conditioner can malfunction. The blower is a major part that commonly fails on a cars air conditioning unit. While its not always easy to tell if this is the problem, there are several tests a person can run to test the blower and see if that is the problem.
Instructions
- 1
Turn on the cars air conditioner to full blast while the engine is running. Feel for any type of a breeze. If no breeze hits your hand, theres a good chance that the cars A/C blower is to blame. No wind at all means the A/C blower is not working at all.
2Hold your hand over the air conditioner vent while the air is on at full blast. After feeling the air, turn the vent down to half speed. If there is no change in fan speed, then this can mean that the A/C blower is the main problem.
3Turn off the engine and open the hood to look at the engine. Have the picture of your cars specific air conditioning system on hand.
4Check the connector to make sure its not loose. If the connector is loose, plug it in firmly and restart the car. Check the air conditioning vents to see if the same problems still exist.
5Check the plastic tube from the blower motor next. Look for tears, wear or even if the tube is disconnected. This is normally located on the lower left hand side of the motor, and must be in perfect working condition. Any damage to this part of the blower engine will prevent the cars A/C from fully working.
Thursday, October 10, 2013
How to Access the Heater Blower in a 2001 Honda Accord
While it can be uncomfortable to get into your Accord and discover that your blower motor is not working, you can feel better knowing that its a simple repair that you can take on at home. When the blower motor stops working, no amount of manipulation of the system will make warm air come through the vents. Before rushing to replace the blower motor, you may be able to check the connections and see if that fixes the problem.
Instructions
- 1
Locate the blower motor under the dashboard of your Accord. The motor is located just to the right of center in the footwell of your car.
2Remove the screws from the blower motor cover by turning them counterclockwise with the Phillips screwdriver. These screws are located on the bottom of the blower motor cover.
3Pull down on the blower motor cover to gain access to the blower motor assembly.
Saturday, September 28, 2013
How to Replace a Blower Fan in an Excursion
The Ford Excursion is a full-size sport utility vehicle that was in production from 2000 to 2005. The blower motor delivers hot and cold air into the cab of the vehicle for temperature-control purposes. The procedure for replacing the blower fan in an Excursion varies slightly according to the engine in the vehicle. The engine options for a Ford Excurion include 5.4-liter, 6.8-liter and 7.3-liter engines.
Instructions
- 1
Perform this step only if your vehicle has a 7.3-liter engine. Detach the electrical connector from the vacuum pump. Disconnect the bolts from the mounting bracket of the blower motor with a socket wrench. Remove the hose from the vacuum pump on the blower motor and disconnect the vacuum pump. Remove the mounting bracket from the vehicle.
2Perform this step only if your vehicle has a 5.4-liter or 6.8-liter engine. Remove the electrical connector from the speed control servo. Disconnect the mounting bolts from the servo with a socket wrench and remove the servo from the vehicle.
3Disconnect the electrical connector and ventilation tube from the blower motor. Remove the retaining screws from the blower motor with a socket wrench and remove the blower motor from the vehicle without damaging the blower motor wheel.
4Release the push clip on the blower motor wheel and disconnect the wheel from the blower motor.
5Install the blower motor wheel to the new blower motor and attach the retaining clip for the wheel. Mount the blower motor to the vehicle and tighten the retaining screws for the blower motor to between 18 and 31 inch-pounds with a torque wrench. Connect the ventilation tube and electrical connector for the blower motor.
6Install the components you removed in steps 1 or 2 to complete the installation of the new blower motor.