Showing posts with label motor. Show all posts
Showing posts with label motor. Show all posts

Monday, November 17, 2014

How to Wire a Blower Motor Resistor

How to Wire a Blower Motor Resistor

Most vehicles today have multiple fan speeds for the heat and A/C. These speeds are controlled by a blower motor resistor. The blower motor resistor is a small electrical device that controls the voltage to the fan motor. If the resistor becomes defective, you may only have one working speed on your fan control. If this problem occurs, the blower motor resistor will need to be replaced. It s a fairly inexpensive part and is available at most car part stores.

Instructions

    1

    Locate the heater blower resistor in your vehicle. It is typically mounted under the dash near the blower motor. You may need to check your vehicles repair guide, or your car dealership to help determine the resistors location. Parts of the dash may need to be removed depending on resistor location.

    2

    Remove the wire connector from the blower motor resistor by lifting the tab on the connector and gently pulling the connector off the resistor. This may require working the connector back and forth a few times to free it from the resistor.

    3

    Remove the two screws holding the resistor in place. These may be screws or small bolts depending on your vehicle. The resistor should now be able to be removed.

    4

    Position the new resistor in place, and secure it with the two screws. Reconnect the wire connector by firmly pressing it onto the resistor. Replace and dash parts that were previously removed.

Read More.. >

Wednesday, April 9, 2014

How to Repair a Heater Motor Resistor on a 1999 BMW Z3 2 5L

The heater motor resistor on a 1999 BMW Z3 2.5-liter roadster is integrated into heater motor itself. This resistor plugs into the front side of the motor assembly. The heater resistor is not repairable; it must be removed and replaced if it fails. This resistor allows the motor to spin at variable speeds, consequently allowing the ventilation system inside the roadster to blow hot or cold air at different speeds. A bad motor resistor will either allow too much or too little current in to the motor, severely limiting the variable fan speed function of the HVAC system.

Instructions

Removal

    1

    Pry off both wiper arm caps with a small flat-head screwdriver, then remove the wiper arm bolts with a ratchet and socket. Mark the position of the wiper arms in relation to the spindles with a small tube of white paint. Lift the wiper arm up so they are at a 90-degree angle to the windshield, then lift the arms off of the wiper spindle gears.

    2

    Disconnect the washer pump tubing from the air intake/heating grille. Open the hood, then pry out the plastic retaining clips on both ends of the air intake/heating grille with the flat-head screwdriver. Lift the air intake/heating grille up and away from the lower windshield area, detach the remaining washer pump hoses, and remove the grille completely.

    3

    Disconnect the wiper motors electrical harness connector. Remove the bolts holding the wiper motor and arm assembly to the inside cowl, using a ratchet and socket, then slide the entire assembly to the left in order to disengage it from the integrated hooks. Lift the assembly out of the vehicle and set it on the ground or on a workbench.

    4

    Disengage the clamps on the blower motor fan cover by pushing them to the left until the pop loose, then set the cover aside.

    5

    Locate the heater motor resistor, directly below the motor body in the center of the assembly. Pry the resistor out of the fan assembly with a flat-head screwdriver. Discard the old resistor.

    6

    Press the new resistor into the fan motor assembly until its fully-seated.

    7

    Reinstall the heater motor cover and re-fasten the covers retaining clamps.

    8

    Position the wiper motor and wiper arm assembly inside the cowl section and slide it to the right to engage the locking tabs. Reinstall the retaining bolts for the wiper motor and wiper arm assembly.

    9

    Connect the washer pump hose to the underside of the air intake/heating grille assembly. Position the assembly over the cowl area and connect the top washer pump hose to the air intake/heating assembly.

    10

    Reinstall the plastic retaining pins on the corners of the air intake/heating grille assembly and press them down until they are fully-seated. Reinstall the wiper arms into their original position and then reinstall the wiper arm retaining bolts. Reinstall the wiper arm caps and test both systems to ensure proper operation.

Read More.. >

Sunday, January 12, 2014

What Happens If a Motor Mount Is Broken

What Happens If a Motor Mount Is Broken?

A motor mount does more than simply hold a motor in place. A motor mount utilizes a rubber bushing to hold a cars engine, which helps to dampen vibration and movement that can cause damage to the engine and surrounding components.

Noise and Vibration

    A broken motor mount will cause a significant increase in noise and vibration. As the motor moves within the broken mount, the engine often strikes the mount, creating a loud thump. The normal vibration of the motor that is dampened by the mount will often also be transferred to the entire vehicle, causing a noticeable shake.

Engine Component Damage

    As the motor moves, damage may also occur to the flexible hoses and wiring that run to the motor. While these parts are designed for flexibility, the sudden and longer movements of a motor that is not properly secured can pull wires and hoses loose as well as weaken them. A broken motor mount may also cause exhaust leaks.

Motor Mount Damage

    When a motor mount is broken, the motor is allowed to move more than intended. This causes additional stress to the other motor mounts, which will quickly wear and may break under the added strain.

Read More.. >