Showing posts with label bmw. Show all posts
Showing posts with label bmw. Show all posts

Tuesday, April 29, 2014

How to Reset the Brake Light on a BMW 528i

How to Reset the Brake Light on a BMW 528i

The On-Board Diagnostics computer, or OBD, on your BMW 528i stores trouble codes that come from sensors positioned throughout the vehicle. These sensors keep track of the mechanical functions of your vehicle. When you see the ABS or Antilock Brake light flash on your instrument panel, you know there is a malfunction with your braking system. This needs to be looked at and repaired as soon as possible by a qualified mechanic. Once the repairs have been made, you need to reset the brake light to ensure the vehicles computer will continue to properly monitor the braking system.

Instructions

    1

    Locate the fuse panel cover on the drivers side dashboard, near the foot well. Use your fingers to pull down on it from the top.

    2

    Find a large port on the fuse panel. Plug the connective end of the OBD reset tool into this port.

    3

    Put the key into the ignition and turn it to the "on" position. Dont turn on the engine, though. This will power on the OBD reset tool automatically.

    4

    Wait for the codes to flash on the OBD reset tool screen. Use the arrow keys on the reset tool to find and select "Delete" on the menu screen. Some OBD reset tools have a "Delete" button on the face of the tool. Either way, select "Delete" and wait for the ABS light to blink and then turn off on the instrument panel.

    5

    Unplug the tool from the port and replace the fuse panel cover. Turn off the vehicle and wait 60 seconds. Turn the engine on and verify the ABS light is off.

Read More.. >

Sunday, April 27, 2014

BMW Alignment Specifications

BMW Alignment Specifications

BMW automobiles have a sterling reputation for durability and overall customer satisfaction, according to Pelican Parts. In addition to engine and electrical components, alignment specifications are important to keep your BMW physically balanced and safe to handle. If your steering wheel seems misaligned or your car veers to the left or right it may be time for an alignment adjustment. Standard BMWs may included "nonadjustable" alignment components, so see an automotive professional with questions or concerns.

BMW Camber

    Camber alignment specifications are included on the front and back end of a BMW. A zero camber design means tires sit perfectly upright on both the left and right side of the vehicle, making tire pressure evenly distributed. Negative camber indicates tires that tilt towards one another while positive camber ers to tires tilting outwards. BMWs may require various manipulations of camber, depending on the model. A BMW 3-Series, for example, best handles on standard street conditions and vehicle turns when the camber is slightly negative.

BMW Caster

    Caster relates to steering alignment. Zero caster ers to a steering axis that, when angled vertically, provides for straight driving. Positive caster indicates strut angling toward the back end of the vehicle, while negative caster means strut angling toward the front. BMW caster --- as with camber --- varies depending upon the model, although most models require 3-9 degrees of angle variety. Front-end and back-end caster can be analyzed independently.

BMW Toe

    Toe-in ers to tires where the front edges are angled closer together than back edges. Alternatively, toe-out means tires that angle into each other more on the back edge. Toe helps cars handle while making wide and sharp turns. Toe is adjusted by manipulating the tie rods. Minimal toe-out calibrations may be required for some BMW models, although tires with "neutral" toe are usually most reliable.

Read More.. >

Saturday, April 19, 2014

1989 BMW 535I Fuel Pump Replacement Instructions

The BMW 5 series is a mid-size car manufactured by BMW, and the 1989 BMW 535i belongs to the third generation in this series. It is a 4-door sedan with a 6-cylinder 3.4-liter engine that uses fuel injection. This requires an electric fuel pump to maintain the fuel system under high pressure. The fuel pump in a 1989 BMW 535I is on top of the fuel pump tank and is accessible from the rear trunk.

Instructions

    1

    Drain the fuel tank if it contains a high level of fuel. Place one and of a hose into the field tank and the other end into a container approved for gasoline. Siphon the fuel from the field tank into the container.

    2

    Remove the panels in the trunk. Loosen the mounting screws for the access cover in the right front corner of the trunk with a socket wrench and remove the access cover. Disconnect the fuel lines and electrical connector for the fuel pump.

    3

    Attach tool 16 1 020 to a socket wrench and use this assembly to turn the mounting ring on the fuel pump assembly counterclockwise. Remove the mounting ring from the fuel pump assembly. Detach the fuel pump assembly from the fuel tank. Depress the mounting hooks to remove the fuel pump from the rest of the fuel pump assembly.

    4

    Disconnect the fuel lines and electrical connectors from the fuel pump. Remove the mounting screws for the fuel check valve and pressure damper with a socket wrench. Pull the fuel pump from its holder. Remove the mounting screw from the fuel filter, and detach the fuel filter from the fuel pump. Discard the O-ring for the fuel pump.

    5

    Place a new O-ring on the new fuel pump and install the fuel pump by reversing steps two through four. Tighten the mounting ring on the fuel pump assembly to between 27 and 31 foot-pounds with tool 16 1 020. Check for leaks in the fuel system and ill the fuel tank.

Read More.. >

Wednesday, April 9, 2014

How to Repair a Heater Motor Resistor on a 1999 BMW Z3 2 5L

The heater motor resistor on a 1999 BMW Z3 2.5-liter roadster is integrated into heater motor itself. This resistor plugs into the front side of the motor assembly. The heater resistor is not repairable; it must be removed and replaced if it fails. This resistor allows the motor to spin at variable speeds, consequently allowing the ventilation system inside the roadster to blow hot or cold air at different speeds. A bad motor resistor will either allow too much or too little current in to the motor, severely limiting the variable fan speed function of the HVAC system.

Instructions

Removal

    1

    Pry off both wiper arm caps with a small flat-head screwdriver, then remove the wiper arm bolts with a ratchet and socket. Mark the position of the wiper arms in relation to the spindles with a small tube of white paint. Lift the wiper arm up so they are at a 90-degree angle to the windshield, then lift the arms off of the wiper spindle gears.

    2

    Disconnect the washer pump tubing from the air intake/heating grille. Open the hood, then pry out the plastic retaining clips on both ends of the air intake/heating grille with the flat-head screwdriver. Lift the air intake/heating grille up and away from the lower windshield area, detach the remaining washer pump hoses, and remove the grille completely.

    3

    Disconnect the wiper motors electrical harness connector. Remove the bolts holding the wiper motor and arm assembly to the inside cowl, using a ratchet and socket, then slide the entire assembly to the left in order to disengage it from the integrated hooks. Lift the assembly out of the vehicle and set it on the ground or on a workbench.

    4

    Disengage the clamps on the blower motor fan cover by pushing them to the left until the pop loose, then set the cover aside.

    5

    Locate the heater motor resistor, directly below the motor body in the center of the assembly. Pry the resistor out of the fan assembly with a flat-head screwdriver. Discard the old resistor.

    6

    Press the new resistor into the fan motor assembly until its fully-seated.

    7

    Reinstall the heater motor cover and re-fasten the covers retaining clamps.

    8

    Position the wiper motor and wiper arm assembly inside the cowl section and slide it to the right to engage the locking tabs. Reinstall the retaining bolts for the wiper motor and wiper arm assembly.

    9

    Connect the washer pump hose to the underside of the air intake/heating grille assembly. Position the assembly over the cowl area and connect the top washer pump hose to the air intake/heating assembly.

    10

    Reinstall the plastic retaining pins on the corners of the air intake/heating grille assembly and press them down until they are fully-seated. Reinstall the wiper arms into their original position and then reinstall the wiper arm retaining bolts. Reinstall the wiper arm caps and test both systems to ensure proper operation.

Read More.. >

Thursday, March 6, 2014

How to Access Trouble Codes on a 1994 BMW 530i

How to Access Trouble Codes on a 1994 BMW 530i

You can access trouble codes on your 94 BMW 530i right from your home garage, saving yourself time and money. To access the codes you must purchase or borrow an OBD I code scanner. These small, computerized devices are available at your local auto parts retailer. The scanner reads trouble codes stored in the vehicles On-Board Diagnostics computer. Each code gives you specific information about the vehicle to help you diagnose the problem with your BMW.

Instructions

    1

    Locate a port on the drivers side dashboard near the steering column. This port is the same size and shape as the connector end on the OBD I code scanner. Plug the scanner into the port, taking care not to shove it in and bend the pins.

    2

    Put the key into the ignition and turn it to the "On" position, but dont crank the engine. This will power on most scanners. If not, look for an "on/off" button on the scanner and press it.

    3

    Select "Retrieve Codes" or other similar command on the scanner. Wait for the scanner to display the trouble codes. Write them down on a piece of paper. Look up the codes in the code scanners manual.

    4

    Unplug the scanner and have the vehicle serviced or repaired based on the diagnostic trouble codes.

Read More.. >

Thursday, February 13, 2014

How to Install a Cylinder Head on a BMW E28

How to Install a Cylinder Head on a BMW E28

The BMW E28 is one of the companys 5-Series line of cars. It was manufactured between 1981 and 1988, and came standard with a 24 valve cylinder head engine known as the S38. Like all vehicles, the E28 requires regular maintenance. If you find that one or more of your cylinder heads are beginning to wear out, it is advisable to replace them with new ones. If you dont like spending hundreds of dollars on a mechanics labor costs, it is possible to change the head yourself.

Instructions

    1

    Unscrew the exhaust pipes and remove them from the exhaust manifold.

    2

    Unscrew the coolant plug and drain the fluid into your oil pan.

    3

    Disconnect the throttle and cruise control cables.

    4

    Unscrew the vacuum hose and remove it from the air cleaner along with the sensor.

    5

    Disconnect the diagnosis and radiator hoses and remove the fuel lines.

    6

    Pull off the plugs on the fuel connectors and disconnect the ignition coil.

    7

    Disconnect the vent hose.

    8

    Remove the nuts from the cylinder head cover with your wrench and set them aside. Remove the cylinder head cover.

    9

    Remove the 14 exposed bolts of the cylinder head, moving from the middle of the head outward.

    10

    Remove and replace the cylinder head.

    11

    Replace the cylinder head bolts, cylinder head cover, vent hose, ignition coil, fuel lines, diagnosis and radiator hoses, air cleaner sensor, vacuum hoses, throttle and cruise control cables, coolant plug, and exhaust pipes in the reverse order that you removed them. Refill your coolant reservoir with the fluid in your oil pan to complete the process.

Read More.. >

Saturday, October 19, 2013

How to Replace the Fuel Pump on a 1991 525 BMW

The BMW 5 series of vehicles consists of midsize cars and has been in production since 1972. The 1991 BMW 525 has a BMW M50B25 engine, which is a 6-cylinder 2.5L engine generating 189 horsepower. This engine uses fuel injection, which requires the fuel pump to deliver fuel to the injectors under high pressure. The fuel pump in the BMW 525 is attached to the fuel sender, and is accessible from the trunk of the vehicle.

Instructions

    1

    Drain the fuel from the fuel tank, so that the tank is no more than 1/4 full. Remove the panels in the trunk to expose the access cover in the front right corner of the trunk. Unfasten the mounting screws for the access cover with a socket wrench, and remove the access cover. Disconnect the fuel lines and the electrical connector from the fuel sending unit.

    2

    Attach tool 16 1 020 to a socket wrench and use it to turn the large mounting ring on the fuel sending unit counterclockwise. Remove the mounting ring from the fuel sending unit. Discard the gasket on the fuel sending unit.

    3

    Pull the fuel sending unit from the fuel tank without spilling the fuel in the fuel sending unit. Squeeze the mounting hooks on the fuel pump to remove it from the fuel sending unit. Disconnect the fuel hoses and electrical wiring from the fuel pump. Turn the pressure damper on the fuel pump counterclockwise, and remove it from the fuel pump. Remove the fuel pump from its holder. Loosen the mounting screw for the fuel filter, and remove the fuel filter from the fuel pump.

    4

    Connect the fuel filter on the bottom of the new fuel pump, and place the fuel pump into its holder on the fuel sending unit. Connect the pressure damper to the fuel pump. Attach the fuel lines and electrical wiring to the fuel pump. Attach the fuel pump to the fuel sending unit by securing the fuel pump with the mounting hooks.

    5

    Install the new gasket for the fuel sending unit and mount it to the fuel tank. Attach the mounting ring to the fuel sending unit, and tighten the mounting ring to between 27 and 31 foot-pounds with tool 16 1 020. Connect the fuel lines and electrical wiring to the fuel sending unit. Replace the trunk access cover and trunk panels.

Read More.. >