Showing posts with label heater. Show all posts
Showing posts with label heater. Show all posts

Wednesday, April 30, 2014

How to Replace the Heater on a 1992 Mazda B2600

The heater in the 1992 Mazda B2600 is a radiator that uses hot coolant from the engine to heat the cab of the truck. The procedure for replacing the heater is the same for all Mazda trucks made from 1987 to 1993.

Instructions

    1

    Disconnect the negative battery cable with a socket wrench to ensure the engine doesnt start while replacing the heater. Put a drain pan under the radiator, and open the drain plug. Allow the coolant to drain from the radiator, and replace the drain plug.

    2

    Disconnect the shield for the water valve on the heaters left side with a socket wrench. Detach the coolant hoses from the heater, and remove the housing for the control cable from its mounting clip on the heater. Disconnect the cable wires from the heaters crank arms. Detach the electrical connector from the fan motor.

    3

    Remove the glove compartment with a socket wrench to provide clearance for the heater. Disconnect the retaining nuts for the heater that are inside the glove compartment. Detach the defroster ducts from the heater, and pull the heater from the dashboard.

    4

    Mount the new heater to the dashboard, and align the mounting studs on the heater with the corresponding holes in the dashboard. Fasten the mounting nuts for the heater, and attach the defroster ducts to the heater. Attach the control cable for the defrost door for the heater to the crank arm.

    5

    Turn the upper control lever to the heat position, and push the crank arm for the heater towards its mounting clip as far as possible. Attach the cable housing to the clip, and fasten the clip to the heater with a socket wrench.

    6

    Attach the control cable for the water valve to the lever for the water valve. Set the heaters control lever to the hot setting, and push the crank arm for the lever as far towards the mounting clip for the control cable as possible. Fasten the screw for the clip with a socket wrench.

    7

    Insert the control cable for the recirculation door into the doors crank arm. Bend the cable, and fasten it into place with the retaining screw. Move the center control lever to the REC setting, and push the crank arm for the recirculation door toward the mounting clip as far as possible.

    8

    Attach the housing for the recirculation door cable to its clip, and fasten the retaining screw for the clip with a socket wrench. Connect the electrical connector for the fan motor. Attach the coolant hoses to the tubes on the left side of the heater, and fasten the hose clamps. Connect the shield for the heaters water valve with the retaining screws, and install the glove compartment.

    9

    Replace the coolant in the radiator, and reconnect the cable to the negative battery terminal with a socket wrench. Check for coolant leaks, and ensure the heater is functioning properly.

Read More.. >

Wednesday, April 9, 2014

How to Repair a Heater Motor Resistor on a 1999 BMW Z3 2 5L

The heater motor resistor on a 1999 BMW Z3 2.5-liter roadster is integrated into heater motor itself. This resistor plugs into the front side of the motor assembly. The heater resistor is not repairable; it must be removed and replaced if it fails. This resistor allows the motor to spin at variable speeds, consequently allowing the ventilation system inside the roadster to blow hot or cold air at different speeds. A bad motor resistor will either allow too much or too little current in to the motor, severely limiting the variable fan speed function of the HVAC system.

Instructions

Removal

    1

    Pry off both wiper arm caps with a small flat-head screwdriver, then remove the wiper arm bolts with a ratchet and socket. Mark the position of the wiper arms in relation to the spindles with a small tube of white paint. Lift the wiper arm up so they are at a 90-degree angle to the windshield, then lift the arms off of the wiper spindle gears.

    2

    Disconnect the washer pump tubing from the air intake/heating grille. Open the hood, then pry out the plastic retaining clips on both ends of the air intake/heating grille with the flat-head screwdriver. Lift the air intake/heating grille up and away from the lower windshield area, detach the remaining washer pump hoses, and remove the grille completely.

    3

    Disconnect the wiper motors electrical harness connector. Remove the bolts holding the wiper motor and arm assembly to the inside cowl, using a ratchet and socket, then slide the entire assembly to the left in order to disengage it from the integrated hooks. Lift the assembly out of the vehicle and set it on the ground or on a workbench.

    4

    Disengage the clamps on the blower motor fan cover by pushing them to the left until the pop loose, then set the cover aside.

    5

    Locate the heater motor resistor, directly below the motor body in the center of the assembly. Pry the resistor out of the fan assembly with a flat-head screwdriver. Discard the old resistor.

    6

    Press the new resistor into the fan motor assembly until its fully-seated.

    7

    Reinstall the heater motor cover and re-fasten the covers retaining clamps.

    8

    Position the wiper motor and wiper arm assembly inside the cowl section and slide it to the right to engage the locking tabs. Reinstall the retaining bolts for the wiper motor and wiper arm assembly.

    9

    Connect the washer pump hose to the underside of the air intake/heating grille assembly. Position the assembly over the cowl area and connect the top washer pump hose to the air intake/heating assembly.

    10

    Reinstall the plastic retaining pins on the corners of the air intake/heating grille assembly and press them down until they are fully-seated. Reinstall the wiper arms into their original position and then reinstall the wiper arm retaining bolts. Reinstall the wiper arm caps and test both systems to ensure proper operation.

Read More.. >

Friday, January 10, 2014

How to Replace a 1997 Ford F 150 Heater Core

How to Replace a 1997 Ford F-150 Heater Core

The heater core in your 1997 Ford F-150 is a radiator-style unit used to heat the interior of your truck. Coolant flows from the lower radiator hose to and through the heater core. This fluid heats the unit, and a blower fan forces warm air through the core and into the cabin when the heater is turned on. A faulty or clogged heater core will leak coolant onto the inside floorboard on the front passengers side. Replacing the heater core can be a complicated and time-consuming repair because of its location behind the passengers side dashboard.

Instructions

    1

    Raise the hood and disconnect both battery cables using a crescent wrench. Slide the recycling container underneath the radiator drain plug.

    2

    Remove the radiator fill cap. Loosen the radiator drain plug using a socket wrench to drain the radiator coolant. Once drained, replace the plug and tighten. Keep the recycling container in place to capture the excess coolant in the lower radiator hose.

    3

    Disconnect the lower radiator hose where it attaches at the radiator by loosening the squeeze-type hose clamp. Allow the excess fluid to drain into the recycling container.

    4

    Locate the heater core intake and return hose lines that protrude through the passengers side firewall of the engine compartment. Disconnect the hoses from the core nipples by depressing the release clip with a flat-head screwdriver while turning the hose counterclockwise by hand.

    5

    Detach the Torx screws under the front dashboard that hold the dashboard soft cover in place. Reach under the dashboard and remove the mounting bolts attaching the dashboard frame to the interior firewall. This will allow the entire dashboard assembly to swing free and give you enough clearance to access the heater cover and core downward from the windshield.

    6

    Detach the interior heater core intake and return hoses from the core nipples by releasing the squeeze clamps using channel-lock pliers. Remove the hoses by twisting as you pull. Disconnect the heater core ground cable strap that attaches to the interior firewall with a single bolt.

    7

    Take out the four outer mounting bolts holding the heater core cover in place. Remove the four mounting bolts attaching the actual heater core to the interior firewall. Maneuver the old unit out and up toward the windshield. Be careful not to spill the coolant inside the heater core.

    8

    Install the replacement heater core in reverse, downward from the windshield and behind the dashboard. Re-mount the heater core, the core cover and the ground cable strap.

    9

    Reattach the intake and return hoses carefully to the core nipple on the firewall. The nipple hoses are different diameters to prevent you from incorrectly crossing the connection hoses.

    10

    Connect the dashboard frame and cover in reverse of the removal. Tighten all the mounting bolts. Be sure that the airbag remained connected during the repair. If it didnt, reconnect as necessary.

    11

    Reconnect the hoses located in the engine compartment at the firewall core nipple by snapping the hoses in place. Connect the lower radiator hose to the radiator and secure it in place using its squeeze-type hose clamp.

    12

    Refill the radiator with a 55/45 mixture of new anti-freeze and distilled water. Reconnect the battery and start the engine. Run the engine for several minutes to flush out any trapped air within the cooling system.

    13

    Test the replacement heater core by turning the heater on and off continually, observing the change in temperature. Check for leaks at all hose connections.

Read More.. >

Thursday, October 10, 2013

How to Access the Heater Blower in a 2001 Honda Accord

While it can be uncomfortable to get into your Accord and discover that your blower motor is not working, you can feel better knowing that its a simple repair that you can take on at home. When the blower motor stops working, no amount of manipulation of the system will make warm air come through the vents. Before rushing to replace the blower motor, you may be able to check the connections and see if that fixes the problem.

Instructions

    1

    Locate the blower motor under the dashboard of your Accord. The motor is located just to the right of center in the footwell of your car.

    2

    Remove the screws from the blower motor cover by turning them counterclockwise with the Phillips screwdriver. These screws are located on the bottom of the blower motor cover.

    3

    Pull down on the blower motor cover to gain access to the blower motor assembly.

Read More.. >

Saturday, September 21, 2013

Can a Heater Work in a Car Before It Is Warm

As the weather starts to cool, the dials on the temperature controls in your car will inevitably start to migrate toward the "red" end of the dial. As you furiously rub your hands together after hopping in your car and starting the engine on a cold morning, you wonder why the heater doesnt work until the car is warmed. Unfortunately, it cant.

Your Resting Car

    There is a typical temperature range within which the engines of most cars are designed to operate, usually around 200 degrees. When your car is at rest, the mechanical components and fluids are allowed to cool to ambient temperature.

Your Car as it Warms

    You turn the key in the ignition, and the belts begin to turn the pulleys on the engine. Coolant is stored and cooled in the radiator, where it is pulled out by the water pump and circulated through the engine. The coolant then passes through an opening in the firewall (the sheet metal panel separating the engine compartment from the cabin of the vehicle) into the heater core. Similar to the radiator, the heater core has small fins through which the heated coolant passes to dissipate heat. This heat is pulled away from the heater core, using fans, and blown into the cars interior.

Your Car After Reaching Operating Temperature

    When you have driven your car for a few minutes, the engine has reached normal temperature. The coolant from the radiator is keeping the extreme heat of the engine in check. The fluid circulates through the engine and through the heater core. The fans pull hot air from the heater core into the cabin, which heats your cars interior. Until the engine heats, the coolant remains cool. Until the coolant heats, your heater core remains cool. When your heater core heats, so does your cars interior.

Read More.. >

Monday, September 16, 2013

Heater Removal in a Subaru Legacy

The Subaru Legacy is a mid-size sedan that Subaru has manufactured since 1989. The heating unit in a car is a small radiator that contains hot coolant from the engine. The coolant circulates through the heater when the heater is turned on, warming the interior of the car. The procedure for removing the heater in a Subaru Legacy is generally the same for all models made since 1998.

Instructions

    1

    Remove the negative battery cable with a socket wrench to prevent the engine from starting. Wait 10 minutes for the the air bag system to deactivate before continuing with the heater removal procedure.

    2

    Place a clean container under the radiator drain, and open the drain plug with a socket wrench. Drain the coolant from the radiator into the container, and store it for later use. Detach the hoses from the heater below the center of the dashboard, and plug the open ends of the hoses with a clean shop cloth.

    3

    Remove the radio from the center console. Disconnect the retaining screws on the center console with a socket wrench, and remove the center console. Detach the covers from the mounting bolts on the instrument panel with a trim remover, and remove the mounting bolts.

    4

    Detach the trim from the lower part of the pillar in the center of the dash with a trim remover. Remove the covers for the instrument panel on both the driver and passenger sides. Disconnect the cable from the hood release lever. Disconnect the electrical wiring harness under the instrument panel.

    5

    Detach the instrument cluster and glove compartment from the vehicle. Remove the cables for the ventilation control and the electrical connector from the heater. Disconnect the vacuum line from the housing for the blower motor, and detach the feeder wire from the antenna.

    6

    Disconnect the electrical wiring harness from the fuse box. Detach the covers from the lower steering column, and disconnect the retaining bolts from the steering column with a socket wrench. Allow the steering column to hang freely.

    7

    Remove the retaining bolts for the instrument panel, and detach the instrument panel from the vehicle. Disconnect the control cables from the heater, and detach the electrical wiring harness from the blower motor. Remove the air duct between the blower motor and the heater. Lift the heater up and pull it out to remove it from the vehicle.

Read More.. >