Showing posts with label can. Show all posts
Showing posts with label can. Show all posts

Wednesday, January 29, 2014

Can Lean Fuel Mixture Cause Overheating

Can Lean Fuel Mixture Cause Overheating?

Modern engines use various checks and balances to adjust the fuel-to-air ratio inside the combustion chambers. If the engine manages this ratio poorly, many problems can arise---including permanent engine damage.

Ideal Ratio

    Under normal circumstances, an engine needs roughly 14 times as much air as gasoline to burn a fuel-air mixture completely. The combustion process occurs when the oxygen in the air combines with the carbon atoms in the fuel. As engine speed and load change, this ideal ratio will also vary slightly and will undergo adjustments based on momentary demands by the engine computer.

Rich Mixture

    The fuel-to-air ratio becomes "rich" when the mixture contains more fuel than ideal. While it may sound counterintuitive, this condition leads to sluggish engine performance and may harm the spark plugs over time. Naturally, it will also increase fuel consumption.

Lean Mixture

    A lean mixture contains an insufficient amount of fuel given the quantity of air. This condition leads to a rough idle and, in more extreme cases, stalling of the engine. It can also result in overheating because the spraying of fuel into the intake port or directly into combustion chambers has a cooling effect on the engine.

Read More.. >

Monday, September 23, 2013

How Can I Recharge a Dead Battery

How Can I Recharge a Dead Battery?

From time to time, drivers unintentionally leave the lights or radio running on the car and let the battery run dead. Automotive and outdoor recreation vehicle batteries are not cheap and most owners try to avoid replacing them any more often than necessary. One way to avoid early replacement is to recharge the battery and determine if it is dead or just in need of a recharge. Recharging the battery can take between a few and 30 hours. If you dont have a battery charger handy, you can let the cars alternator recharge the battery while the engine is running.

Instructions

Recharging After a Jump Start

    1

    Open the hood of your car and locate the battery. Most manufacturers place the battery in either the right-front or left-front of the engine compartment. Clean any corrosion from the battery posts using a stiff wire brush.

    2

    Pull the front of another car up next to the battery. Bring the battery of the other car as close to your battery as possible.

    3

    Turn off the engine of the running car. Providing that the other cars battery is fully charged, it will have enough power to start the car with your battery connected to it.

    4

    Connect a pair of battery cables between the two cars. The order that you connect the cables is important. Connect the red (positive) jumper cable ends to the two positive posts of the two batteries -- the one on the dead battery first. Connect the black (negative) jumper cable first to the negative post of the car with the functioning battery and then connect the other negative clamp to a piece of unpainted metal on the car with the dead battery -- as far from it as you can. This is to obviate the possibility of an explosion, even though this is not likely.

    5

    Start the engine of the other car and rev it up for a few minutes. After revving the cars engine, try to start your car. If you have trouble, check the cables and ensure you have attached the cables firmly to both vehicles.

    6

    Remove the jumper cables in the reverse order of the way you attached them. Allow the car to idle for 30 minutes or drive it, to recharge the battery. Then, take the battery to a battery charger to get a full recharge. If the battery fails to hold the charge after using the battery charger and you cant start your car, you need to purchase a new battery.

Charging with a Battery Charger

    7

    Take your battery charger near the front of the car with the hood opened. There is no need to remove the battery from the vehicle to use the battery charger to recharge your battery.

    8

    Turn the battery charger off and ensure that the plug is not in the wall socket. This minimizes the chance of an accidental shock when hooking up the battery.

    9

    Connect the positive lead of the charger to the positive post of the battery and the negative lead of the charger to the engine block or car frame. Most cars have a negative ground and you hook up the charger as outlined, but for cars that have a positive ground -- this is very uncommon -- hook the charger up in the reverse. For a positive-ground car, connect the negative lead of the charger to the negative pole of the battery and the positive lead to the car frame or engine block.

    10

    Set the controls of the charger, if present, to 12V, charging current value,;select between manual and automatic and set the time on the timer, if the charger has one.

    11

    Plug the charger into the wall socket. Ensure the plug and wall socket are equipped for grounded prongs.

    12

    Check the ammeter on the charger to check that the charger is charging the battery. Allow the charger to run until charging stops; depending on the charge level of the battery this may require at least 24 hours. Most chargers have a trickle charger that will keep the battery charged until it is disconnected. The trickle charging occurs at lower amperage than the normal mode.

    13

    Unplug the battery charger and move the switch selector to the "Off" position. Remove the charger clip attached to the car frame or engine block. Finally, unclip the lead attached to the battery post.

    14

    Use a voltmeter to test the voltage between the two posts on the battery. If the battery shows no charge, you will have to replace the battery.

Read More.. >

Saturday, September 21, 2013

Can a Heater Work in a Car Before It Is Warm

As the weather starts to cool, the dials on the temperature controls in your car will inevitably start to migrate toward the "red" end of the dial. As you furiously rub your hands together after hopping in your car and starting the engine on a cold morning, you wonder why the heater doesnt work until the car is warmed. Unfortunately, it cant.

Your Resting Car

    There is a typical temperature range within which the engines of most cars are designed to operate, usually around 200 degrees. When your car is at rest, the mechanical components and fluids are allowed to cool to ambient temperature.

Your Car as it Warms

    You turn the key in the ignition, and the belts begin to turn the pulleys on the engine. Coolant is stored and cooled in the radiator, where it is pulled out by the water pump and circulated through the engine. The coolant then passes through an opening in the firewall (the sheet metal panel separating the engine compartment from the cabin of the vehicle) into the heater core. Similar to the radiator, the heater core has small fins through which the heated coolant passes to dissipate heat. This heat is pulled away from the heater core, using fans, and blown into the cars interior.

Your Car After Reaching Operating Temperature

    When you have driven your car for a few minutes, the engine has reached normal temperature. The coolant from the radiator is keeping the extreme heat of the engine in check. The fluid circulates through the engine and through the heater core. The fans pull hot air from the heater core into the cabin, which heats your cars interior. Until the engine heats, the coolant remains cool. Until the coolant heats, your heater core remains cool. When your heater core heats, so does your cars interior.

Read More.. >