Wednesday, May 21, 2014
How to Repair a Battery Side Post Terminal
Side post battery terminals are common in some car models, such as General Motors. When corrosion builds up on one or both of the terminals, it can cause interference in the flow of electricity to the vehicle. The result will be a car that wont start. You can prevent this from happening with the simple repair of removing the corrosion from the battery terminal post. Always be sure to follow any additional instructions provided by your vehicles manufacturer.
Instructions
- 1
Put on the safety glasses and gloves.
2Unscrew the battery cable clamps from the side battery posts terminal with the adjustable socket wrench. Start with the negative battery cable first, then the positive battery cable. Secure the cables out of the way so they will not flop back and come into contact with the terminal posts.
3Apply the detergent or a paste made from baking soda and water to each battery terminal post. Scrub with the wire brush to remove corrosion.
4Rinse with water, taking care not to get any water in the battery vents. Dry thoroughly with a clean, lint-free cloth.
5Apply a thin coat of petroleum jelly to each of the side battery terminal posts.
6Reattach the positive cable to the positive post, first with your hand and then with the socket wrench. Repeat to reattach the negative cable to the negative post.
Tuesday, May 20, 2014
The Battery Specifications for a 1991 Honda Accord Station Wagon Ex
The Honda Accord EX wagon was introduced in 1991. The EX was the upmarket version of the Accord wagon, with a 140-horsepower engine and four-wheel anti-lock disc brakes. Accord wagons are known for their reliability, but most owners will need to purchase at least one new battery during their cars lifetime.
About Batteries
Most cars require a 12-volt, six-cell, negative grounded, lead-acid battery. Batteries are produced by a number of manufacturers. Batteries differ in their cold-cranking amps and reserve capacity. BatteryFAQ.org recommends buying a battery with the maximum available reserve capacity and the maximum cold-cranking amps for your climate. Cold-cranking amps (CCA) can vary from 450 to 850. If you live in a colder climate, you should choose a battery rated with greater CCA.
Battery Size
Batteries are classified into "BCI group numbers," commonly erred to as "sizes." The numerical battery size, such as 24, 35 or 75, takes into account the physical dimensions of the battery, whether the terminals are on the top or side, and its polarity. The 1991 Honda Accord EX wagon requires battery size 24. Size-24 batteries are no larger than 10.25 inches in height, 6.8125 inches wide, and 8.875 inches long. Be caul not to buy a size-24F battery, which would have the terminals reversed.
Battery Freshness
Batteries are stamped with a manufacturing date. Since batteries are perishable, you should always select a battery produced within the last year. BatteryFAQ.com recommends only purchasing a battery manufactured in the last six months.
Monday, May 5, 2014
How to Remove the Battery From a Ford Edge
Removing the battery from your Ford Edge will allow you to test or replace the battery when it is not functioning properly. The battery is under the hood on the drivers side of the engine compartment. If you suspect your battery is malfunctioning, removing it will allow you to take it to an auto parts store or service center to load test and analyze the condition of the battery for you. Many auto parts stores offer this service free, if you bring the battery to them.
Instructions
- 1
Park the vehicle on a level surface and turn off the ignition. Open and secure the hood. Locate the negative battery cable end on the negative battery terminal. Loosen the retaining bolt on the cable end with a socket and ratchet, lift the cable off the battery and away from the terminal.
2Loosen the retaining bolt on the positive battery cable end with a ratchet and socket and lift the cable off the battery. Isolate the positive battery cable away from the battery.
3Locate the retaining bolt on the front of the battery, near the bottom. Remove the bolt and hold-down bracket from the battery with a socket, extension and ratchet.
4Lift the battery straight up and off the tray. Move the battery out of the battery compartment and set it aside in a safe place.
Saturday, March 15, 2014
How to Clean a Forklift Battery
You can use a forklift in a warehouse or a farm to transport large, heavy goods. Some forklifts operate solely on battery power, and others are gas-powered and use batteries to power lights and to assist with turning the combustion engines. You may have to clean the forklifts battery from time to time if it has overflowed or has gotten dirty from mud or oil spilling on it.
Instructions
- 1
Remove the battery from its case using a screwdriver. Place the forklift battery on a pallet or on the floor. Put on gloves and keep them on during the entire cleaning process.
2Check for damage or cracks in the battery. Check whether the battery acid has overspilled from inside the battery. The acid is highly corrosive and conductive, and it should never get on outside surfaces.
3Mix 5 oz. baking soda with 1 gallon water in a bucket. Add more baking soda if the battery is heavily polluted with acid. The baking soda will neutralize the acids on the battery. Rinse the battery with the baking soda mix immediately after noticing that it has overspilled. Use plenty of water to completely dilute and wash off the overspilled acid.
4Brush the battery with a wire brush to remove any other dirt from the batterys surface. Rinse the battery once again with plenty of water to wash off any remaining dirt.
5Replace the battery into its case.
Saturday, September 28, 2013
How to Install a Battery Terminal
A cars battery connects to the vehicle through the terminals, which are the sleeves that fit over the battery posts. Acid and rust degrade the terminals, which, if not monitored, will cause the terminals to fracture and break. The wiring to the terminals is typically covered with rubber, protecting it from exposure to acid and water. Replacing the terminal is similar to splicing a line and only requires a few tools to complete.
Instructions
- 1
Disconnect the terminals from the vehicles battery starting with the negative terminal. Use a ratchet to loosen the terminal then pull it free from the battery.
2Cut the damaged wire and terminal off with bolt or wire cutters. Cut the wire just behind the existing rubber sleeve to remove any corroded parts of the wire.
3Use a razor blade or utility knife to trim off 1 inch of rubber from the rubber sleeve. Slice the rubber along its length then slide the rubber around the circumference of the wire. Pull the rubber off to expose the clean wire.
4Place the wire into the new terminal retaining bolts. You have a few options for replacement terminals. The easiest to use will have the retaining bolts that tighten down onto the wire with a ratchet. The other types require specialized crimping tools to grab the wire. Tighten the retaining bolts until the wire cannot be pulled from the new terminal.
5Install the terminals back onto the battery, starting with the positive connection. Make sure the terminals are pushed all the way onto the battery posts. Tighten down the terminals until they are secure.
Monday, September 23, 2013
How Can I Recharge a Dead Battery
From time to time, drivers unintentionally leave the lights or radio running on the car and let the battery run dead. Automotive and outdoor recreation vehicle batteries are not cheap and most owners try to avoid replacing them any more often than necessary. One way to avoid early replacement is to recharge the battery and determine if it is dead or just in need of a recharge. Recharging the battery can take between a few and 30 hours. If you dont have a battery charger handy, you can let the cars alternator recharge the battery while the engine is running.
Instructions
Recharging After a Jump Start
- 1
Open the hood of your car and locate the battery. Most manufacturers place the battery in either the right-front or left-front of the engine compartment. Clean any corrosion from the battery posts using a stiff wire brush.
2Pull the front of another car up next to the battery. Bring the battery of the other car as close to your battery as possible.
3Turn off the engine of the running car. Providing that the other cars battery is fully charged, it will have enough power to start the car with your battery connected to it.
4Connect a pair of battery cables between the two cars. The order that you connect the cables is important. Connect the red (positive) jumper cable ends to the two positive posts of the two batteries -- the one on the dead battery first. Connect the black (negative) jumper cable first to the negative post of the car with the functioning battery and then connect the other negative clamp to a piece of unpainted metal on the car with the dead battery -- as far from it as you can. This is to obviate the possibility of an explosion, even though this is not likely.
5Start the engine of the other car and rev it up for a few minutes. After revving the cars engine, try to start your car. If you have trouble, check the cables and ensure you have attached the cables firmly to both vehicles.
6Remove the jumper cables in the reverse order of the way you attached them. Allow the car to idle for 30 minutes or drive it, to recharge the battery. Then, take the battery to a battery charger to get a full recharge. If the battery fails to hold the charge after using the battery charger and you cant start your car, you need to purchase a new battery.
Charging with a Battery Charger
- 7
Take your battery charger near the front of the car with the hood opened. There is no need to remove the battery from the vehicle to use the battery charger to recharge your battery.
8Turn the battery charger off and ensure that the plug is not in the wall socket. This minimizes the chance of an accidental shock when hooking up the battery.
9Connect the positive lead of the charger to the positive post of the battery and the negative lead of the charger to the engine block or car frame. Most cars have a negative ground and you hook up the charger as outlined, but for cars that have a positive ground -- this is very uncommon -- hook the charger up in the reverse. For a positive-ground car, connect the negative lead of the charger to the negative pole of the battery and the positive lead to the car frame or engine block.
10Set the controls of the charger, if present, to 12V, charging current value,;select between manual and automatic and set the time on the timer, if the charger has one.
11Plug the charger into the wall socket. Ensure the plug and wall socket are equipped for grounded prongs.
12Check the ammeter on the charger to check that the charger is charging the battery. Allow the charger to run until charging stops; depending on the charge level of the battery this may require at least 24 hours. Most chargers have a trickle charger that will keep the battery charged until it is disconnected. The trickle charging occurs at lower amperage than the normal mode.
13Unplug the battery charger and move the switch selector to the "Off" position. Remove the charger clip attached to the car frame or engine block. Finally, unclip the lead attached to the battery post.
14Use a voltmeter to test the voltage between the two posts on the battery. If the battery shows no charge, you will have to replace the battery.