Showing posts with label 1992. Show all posts
Showing posts with label 1992. Show all posts

Wednesday, April 30, 2014

How to Replace the Heater on a 1992 Mazda B2600

The heater in the 1992 Mazda B2600 is a radiator that uses hot coolant from the engine to heat the cab of the truck. The procedure for replacing the heater is the same for all Mazda trucks made from 1987 to 1993.

Instructions

    1

    Disconnect the negative battery cable with a socket wrench to ensure the engine doesnt start while replacing the heater. Put a drain pan under the radiator, and open the drain plug. Allow the coolant to drain from the radiator, and replace the drain plug.

    2

    Disconnect the shield for the water valve on the heaters left side with a socket wrench. Detach the coolant hoses from the heater, and remove the housing for the control cable from its mounting clip on the heater. Disconnect the cable wires from the heaters crank arms. Detach the electrical connector from the fan motor.

    3

    Remove the glove compartment with a socket wrench to provide clearance for the heater. Disconnect the retaining nuts for the heater that are inside the glove compartment. Detach the defroster ducts from the heater, and pull the heater from the dashboard.

    4

    Mount the new heater to the dashboard, and align the mounting studs on the heater with the corresponding holes in the dashboard. Fasten the mounting nuts for the heater, and attach the defroster ducts to the heater. Attach the control cable for the defrost door for the heater to the crank arm.

    5

    Turn the upper control lever to the heat position, and push the crank arm for the heater towards its mounting clip as far as possible. Attach the cable housing to the clip, and fasten the clip to the heater with a socket wrench.

    6

    Attach the control cable for the water valve to the lever for the water valve. Set the heaters control lever to the hot setting, and push the crank arm for the lever as far towards the mounting clip for the control cable as possible. Fasten the screw for the clip with a socket wrench.

    7

    Insert the control cable for the recirculation door into the doors crank arm. Bend the cable, and fasten it into place with the retaining screw. Move the center control lever to the REC setting, and push the crank arm for the recirculation door toward the mounting clip as far as possible.

    8

    Attach the housing for the recirculation door cable to its clip, and fasten the retaining screw for the clip with a socket wrench. Connect the electrical connector for the fan motor. Attach the coolant hoses to the tubes on the left side of the heater, and fasten the hose clamps. Connect the shield for the heaters water valve with the retaining screws, and install the glove compartment.

    9

    Replace the coolant in the radiator, and reconnect the cable to the negative battery terminal with a socket wrench. Check for coolant leaks, and ensure the heater is functioning properly.

Read More.. >

Monday, April 21, 2014

1992 Plymouth Neon Timing Belt Installation

Neon was first introduced in North America in the early 90s. It is a front-wheel drive compact car that was manufactured by Chrysler Corporations Plymouth and Dodge Brands. It was powered by an inline 4 cylinder 2.0L engine that had an output of 132 horsepower and 130 foot-pounds of torque. It is a small and reliable engine, but it still need periodic service if parts like the timing belt fail.

Instructions

    1

    Disconnect the negative cable of your battery before performing any maintenance work on your engine, to prevent electrical shock or accidental starting. Remove the nut from the negative post with a box-end wrench. Lift the cable from your battery, move it outside of the battery box and close the lid of the battery box.

    2

    Align the sprocket with the arrow on the oil pump housing and then set the crankshaft sprocket to the top dead center (TDC) position. Using a suitable wrench, move crankshaft to 1/2 notch before top dead center.

    3

    Place the camshaft timing marks by aligning the notches on sprockets. Install timing belt, starting at crankshaft, around water pump sprocket, idler pulley, camshaft pulleys and tensioner pulley. Move the crankshaft sprocket to TDC to take up belt slack.

    4

    Install belt tensioner to engine block but do not tighten fasteners. Using a suitable torque wrench on the tensioner pulley, torque the pulley to 28 foot-pounds. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and torque fasteners to 23 foot-pounds.

    5

    Pull the tensioner plunger pin. Pretension is proper when pin can be easily removed or installed. Rotate crankshaft two revolutions and inspect the alignment of the timing marks. If the alignment is improper, repeat the operation.

Read More.. >

Monday, January 27, 2014

1992 Honda Civic Problems

The 1992 Honda Civic has had few complaints or problems over the years, but there have been 13 different recalls from the manufacturer primarily dealing with the exterior lighting, according to Car Complaints and Repair Pal. The other major recall on the 1992 Honda Civic has been on the transmission, but there have been some problems concerning other areas of the vehicle.

Warped Brake Rotors

    One of the biggest problems with the 1992 Honda Civic has been the warping of the brake rotors. A Civic owner can determine if this is the problem easily because the car will vibrate when the brake pedal is applied. This problem with the Honda Civic has not been attributed to any one defect other than standard wear from the brake pads being pressed against the brake rotors. The rotors wear over time and can be easily repaired by shaving down the rotors until the brake rotors are smooth again. Overheating is another cause for the brake rotors to warp along with a misalignment of new brake shoes.

Sun Roof Leaking

    Another common problem of the 1992 Honda Civic is that the sun roof begins to leak. The main cause of this leakage is from the drain plugs, which allow the water drain away from the sun roof, get clogged or plugged up from debris. A Civic owner easily can fix this problem by cleaning out the drain reservoirs located around the sun roof. The water begins to leak over the drivers side or front passenger side of the Civic and is not attributed to the seals around the sun roof.

Starting Problems

    The 1992 Honda Civic has problems starting, according to MSN autos. This starting problem has been attributed to the distributor that controls the signals to the spark plugs or the main relay, which is part of the ignition system. This problem is not part of the recall of the 1992 Honda Civic, but many owners have developed this problem during the ownership of the Civic. According to MSN autos, this starting problem is categorized under critical problems.

Read More.. >

Thursday, December 12, 2013

Radiator Fan Failure in a 1992 Oldsmobile

The radiator cooling fan is vital to the cooling system in a 1992 Oldsmobile. The fan will switch on whenever the coolant reaches a predetermined temperature (200 to 230 degrees F). A properly working fan should come on whenever the air conditioner is switched on, or when the car is in heavy stop-and-go traffic.

Faulty Fuses

    Faulty fuses might cause the fan to stop working. Oldsmobile Regency models have two fan fuses: a 10 amp and a 40 amp. The fuses are located in the covered fuse box under the hood. A diagram of the fuses is fixed to the underside of the cover. Check the fuses to make sure they are in good working order.

Faulty Relays

    Faulty fan relays might cause the radiator fan to stop working. The relays are located in a covered relay panel. The underside of the cover shows a diagram of which component is operated by the given relay. The relays are located on the drivers side of the radiator for the Oldsmobile 98 and 88 models.

Coolant Temperature Sensor

    A faulty coolant temperature sensor can cause the fan from spinning. Most properly functioning General Motors coolant sensors have a resistance of 1,000 ohms at 32 degree F. The sensors resistance will drop below 200 ohm when the engine coolant temperature reaches 200 degrees F. The sensor sends data to the on-board computer, which turns the fan on when conditions warrant extra cooling power.

Read More.. >

Thursday, December 5, 2013

How to Replace a Fuel Injector for a 1992 940 GL Volvo

The Volvo 900 series is a range of mid-size cars made by Volvo during the 1990s, and the 940 models were in production from 1991 to 1997. The 1992 940 GL had a four-cylinder 2.3-liter engine with electronic fuel injection. These fuel injectors deliver a precise ratio of fuel and air to the engine at high pressure. The fuel injectors on the 1992 Volvo 940 GL are on top of the engine and are accessible from the engine compartment.

Instructions

    1

    Remove the fuel pump relay under the dashboard and start the engine. Allow the engine to idle until it stalls to relieve the pressure in the fuel system. Turn the ignition off and replace the fuel pump relay.

    2

    Disconnect the negative battery cable with a socket wrench to prevent the accidental discharge of fuel. Detach the fuel lines and electrical connectors from the fuel injection manifold. Remove the vacuum hose from the fuel pressure regulator. Disconnect the fuel pressure regulator from the bracket of the fuel rail with a socket wrench.

    3

    Remove the retaining bolts for the fuel injection manifold with a socket wrench. Detach the fuel injection manifold and fuel injectors from the engine as an assembly. Secure the fuel injection manifold in place on a work bench and disconnect the fuel injectors from the manifold.

    4

    Remove the O-rings from the fuel injectors and replace them if they show signs of wear. Apply a thin layer of petroleum jelly to the O-rings, and install them onto the new fuel injectors. Connect the fuel injector to the fuel injection manifold and install this assembly onto the engine. Tighten the retaining bolts for the fuel injection manifold with a socket wrench.

    5

    Connect the fuel pressure regulator to the fuel rail bracket and attach the vacuum hose to the fuel pressure regulator with a socket wrench. Connect the fuel lines and electrical connectors to the fuel injection manifold. Connect the cable to negative terminal of the battery. Start the engine and check for fuel leaks.

Read More.. >

Saturday, November 16, 2013

How to Troubleshoot Electrical in a 1992 Ford Explorer

How to Troubleshoot Electrical in a 1992 Ford Explorer

The 1992 Ford Explorer has an electrical system which consist of a power generating device, power distribution conductors, a power storage device, safety fuses and the various loads or devices that are powered by 12 volts DC electrical current. Electrical problems are one of the most common problems with cars. Knowing how to troubleshoot electrical problems with the 1992 Ford Explorer is a valuable skill and can provide significant cost savings as well.

Instructions

    1

    Start the Ford Explorer engine and listen to the sound generated by the engine. A slow cranking engine or an engine that wont crank is indicative of a problem with the car battery or starter motor.

    2

    Turn on the radio and listen to its sound. Press the horn button and listen to the intensity of the sound coming from the horn. Turn on the windshield wipers and then switch the wipers off after a few turns. Any noticeable decline in the performance of the above devices, or their failure to operate, indicates a problem with the battery or alternator, or a blown fuse.

    3

    Set the dial of the multimeter to 12 volts DC range. Place the tip of the red multimeter probe on top of the batterys positive (red) terminal. Place the tip of the black probe on top of the black (negative) terminal, and look at the multimeter. The multimeter should give a reading of 12.5 to 12.8 volts with the engine off. A lower reading indicates the battery has low charge and needs recharging.

    4

    Start the car engine and keep the engine idling. Hold the probes of the multimeter on each hand, and place the tip of the red probe on the batterys red (positive) terminal. Touch the tip of the black (negative) terminal with the black probe, and look at the multimeter. A multimeter reading of 13.6 to 14.3 volts is indicative of an alternator that is charging the battery sufficiently. A lower reading is indicative of a defective alternator.

    5

    Read the owners manual of the 1992 Explorer to know the ampere rating of its alternator. Ask a helper to step on the accelerator gently and increase the vehicles idle speed to 1,200 RPM. Hold the probes of the multimeter on each hand, and place the tip of the red probe on the batterys red (positive) terminal. Touch the tip of the black (negative) terminal with the black probe, and look at the multimeter. The multimeter should display a reading equivalent to the ampere rating stated in the Explorers owners manual. Have the alternator repaired in case the multimeter displays a different figure.

    6

    Open the hood of the car, turn off the engine, and inspect the battery terminals. Look for corrosion or a build-up of white substance on each terminal. Corrosion or acid build-up on the terminals will cause poor contact between the terminal and the battery cable, thus preventing power from running from the battery to the various electrical devices including the starter. Clean the battery terminals to ensure the battery operates properly.

    7

    Read the vehicle owners manual to know the location of the fuse box. The Explorers fuse box is typically found under the hood or under the dash. On the lid of the fuse box note the diagram that indicates the fuse position of each particular circuit. In case a particular device is not working, locate the position of the fuse inside the fuse box by reading the labels in the diagram. Replace the fuse with one of equal amperage If the wire in the fuse is broken or appears blackened.

Read More.. >