Showing posts with label radiator. Show all posts
Showing posts with label radiator. Show all posts

Thursday, December 12, 2013

Radiator Fan Failure in a 1992 Oldsmobile

The radiator cooling fan is vital to the cooling system in a 1992 Oldsmobile. The fan will switch on whenever the coolant reaches a predetermined temperature (200 to 230 degrees F). A properly working fan should come on whenever the air conditioner is switched on, or when the car is in heavy stop-and-go traffic.

Faulty Fuses

    Faulty fuses might cause the fan to stop working. Oldsmobile Regency models have two fan fuses: a 10 amp and a 40 amp. The fuses are located in the covered fuse box under the hood. A diagram of the fuses is fixed to the underside of the cover. Check the fuses to make sure they are in good working order.

Faulty Relays

    Faulty fan relays might cause the radiator fan to stop working. The relays are located in a covered relay panel. The underside of the cover shows a diagram of which component is operated by the given relay. The relays are located on the drivers side of the radiator for the Oldsmobile 98 and 88 models.

Coolant Temperature Sensor

    A faulty coolant temperature sensor can cause the fan from spinning. Most properly functioning General Motors coolant sensors have a resistance of 1,000 ohms at 32 degree F. The sensors resistance will drop below 200 ohm when the engine coolant temperature reaches 200 degrees F. The sensor sends data to the on-board computer, which turns the fan on when conditions warrant extra cooling power.

Read More.. >

Wednesday, November 20, 2013

How to Replace the Radiator in a 1997 Silverado

Replacing the radiator in your 1997 Silverado is a basic automotive repair to perform. Your radiator plays an important role in the trucks overall cooling system. Its primary function is to keep the engine from overheating. As your engines temperature rises, a cooled mixture of coolant flows into the engine and reduces its temperature. Over time, the radiator becomes damaged resulting from objects hitting the front during operation. This damage can cause the water not to properly flow into the engine as necessary. Performing a routine inspection for damage can help prevent your radiator from falling and causing engine overheating.

Instructions

Removal

    1

    Park the truck on a level surface, and set the parking brake. Lift the front end using a floor jack, and carefully place it onto the jack stands. Brace the rear wheels using wheel chocks as an added safety measure.

    2

    Raise the hood, remove the radiator fill cap and disconnect the negative battery cable. Place the recycling container under the radiator drain plug.

    3

    Unscrew the drain plug bolt, and drain all of the antifreeze from the radiator. Securely seal the recycling container, and safety move it to the side.

    4

    Remove the radiator safety shield (shroud) mounted on the top of the radiator. The shroud is held in place using two bolts on either side.

    5

    Remove the main intake radiator hose that attaches to the thermostat housing cover. This hose is held in place by a squeeze-type hose clamp. Detach the hose that leads to the antifreeze reservoir tank.

    6

    Make note of the lower hose connections, which include the radiator hose leading to the water pump, and also the heater core hose line. Disconnect these lower hoses held in place by squeeze clamps.

    7

    Reach underneath the truck, and remove the lower radiator mounting bolts. Then, take out the upper mounting bolts from the engine compartment and lift out the radiator.

Installation

    8

    Carefully hold the replacement radiator in place, and screw in the upper mounting screws by hand. This will hold the radiator in place and allow you to install the lower bolts.

    9

    Install the lower bolts, and securely tighten all of the mounting bolts in place. Reconnect the lower radiator and heater core hoses, and secure them in place using the hose clamps.

    10

    Connect the upper radiator and reservoir hoses and secure them using the hose clamps. Re-mount the safety shield (shroud), and secure it in place using its mounting bolts.

    11

    Start the engine, and fill the radiator with a new 50/50 mixture of antifreeze and water. Let the engine idle for several minutes to bleed out trapped air within the cooling system. Replace the radiator fill cap, and inspect all the connections for leaks.

    12

    Safely raise the truck and remove the floor jacks and wheel chocks. Lower the truck to the ground.

Read More.. >

Thursday, September 19, 2013

How to Bleed Air From a 22RE Radiator

Anytime you open the cooling system, you run the risk of allowing air into the system, rendering it less efficient. This might be caused by a leak, draining and refilling the radiator or simply alowing the coolant level to drop. If you open the radiator cap and the coolant level doesnt reach the rim, there is air present in the Toyota 22RE cooling system and you need to properly remove it to ensure optimal performance.

Instructions

    1

    Ensure that the engine is cool. Remove the radiator cap and see the coolant level reaches the rim. If not, add coolant as specified by the owners manual. Add coolant to the overflow reservoir until it reaches the "Full-Cold" level.

    2

    Place a drain pan under the radiator drain valve, on the bottom passenger side of the radiator. Use your fingers, or a pair of pliers if necesary, to open the radiator drain valve and allow a small amount of coolant to drain out. Close the valve.

    3

    Refill the radiator. Slowly squeeze the upper radiator hose to ensure it has no air inside. Repeat this a few times and top off the radiator. Replace the radiator cap.

    4

    Start the vehicle and turn the heater control to "High." Allow the vehicle to warm up until the upper radiator hose is hot to the touch. This means the thermostat has opened and coolant is flowing through the system. Turn off the engine.

    5

    Check the radiator cap to see if it is cool enough to touch. Place a rag over the cap and slowly open it, releasing pressure a little at a time. Top off the radiator and the overflow reservoir, if necessary. The system is now fully primed with coolant and free of air.

Read More.. >